Compass E175 SIC Flows

Question 1

SIC preflight before being seated

Answer 1

1: Maint logbook- Check
2: Observer’s oxygen regulator and audio control panel
3: Check availability of emergency equipment

Question 2

SIC preflight after being seated

Answer 2

Overhead Panel
1: Electric panel- Set
2: Cockpit lights panel- As required
3: Engine 1 fire handle- Stowed
4: Fuel panel- Set
5: APU Control panel- As required
6: External lights- AS required 
7: Engine 2 fire handle- Stowed
8: Pressurization panel- Set
9: Windshield heating butttons- Auto (in)
10: Ice protection panel- Set
11: Air con/ Pneumatic panel- Set
12: Passenger oxygen panel- Set
----------------------------------------------
Side console
1: Flight deck window- Closed and locked
2: Oxygen quantity, mask, regulator and audio panel- Check
3: EFB- Setup
----------------------------------------------
Glareshield 
1: Glareshield light- As required
2: Display controller panel- Set
----------------------------------------------
Instrument panel
1: ADS probes heater (if installed)- off/ As required
2: Reversionary panel- Set
3: Flight instruments- Set/XCKD
4: Clock- Set
5: ELT- Armed, Red LED not flashing
6: GND PROX G/S INHIB- Check
7: LG WRN INHIB- Check
----------------------------------------------
Alternate gear extension handle- Check
----------------------------------------------
Center pedestal
1: GRND PROX FLAP OVRD- Check
2: Digital Audio control panel- Test/Volumes set
3: MCDU- Set

Question 3

SIC Before Start

Answer 3

1: Enter FOB in the ACARS loadsheet under perf/W&B
2: Send

Question 4

SIC After Start

Answer 4

1: Select Hydraulic Sys 1&2 Elec pump to Auto
2: Shutdown APU unless required to be on

Question 5

SIC Before Taxi

Answer 5

After start and prior to taxi
1: Display TAKEOFF DATA MESSAGE on MCDU #1 and ensure the passenger and cargo distribution is correct
2: Using MCDU #2 and the TAKEOFF DATA MESSAGE
- Update ZFW (Perf init 3/3)
- Enter TO DATASET (TRS page)
- Enter the takeoff flap selection (Takeoff 2/3)
-Enter the Vspeeds (TAKEOFF 3/3)
- Set the STAB trim
- Return to Takeoff flap selection page (takeoff 2/3) for PIC reference
———————————————-
After PIC announces “select flaps__, flight control check
1: Select appropriate flap setting and respond “Takeoff flaps__ Set”
2: Monitor the flight control MFD Synoptic page for control errors
3: Follow the PIC on the rudder pedals to check full range of motion

Question 6

SIC Before Takeoff

Answer 6

1: Verify APU off, or On if required
2: Check brake temps in the green range on the status page and select MAP on the MFD
3: Ensure the assigned code is set in the transponder, and set transponder to TA/RA
4: Press and test the T/O CONFIG button and listen for “Takeoff Okay” confirmation
5: Announce “flight attendants prepare for departure” using PA
6: Accept the call from the FA confirming cabin ready for departure

Question 7

SIC after landing/taxi in

Answer 7

1: Request taxi clearance
2: Set the flaps 0/2 as requested by PIC
3: Place the TACS/Transponder mode selector to ALT ON
4: Select the status page on the MFD
5: Set the pitch trim to 4
6: Set the approximate field elevation in the altitude select window
7: If icing conditions exist, select the ICE PROTECTION MODE switch to ON
8: When the Red X appears on the MFD vertical profile display announce “Cool down complete”

Question 8

SIC When parked at gate

Answer 8

1: Verify that the Ice protection mode is on AUTO
2: Push the APU bleed button IN
3: Reset clock
4: Place Transponder STBY
5: Send ACARS Post flight within 5 mins of Block-in