chapter 16 Flashcards

1
Q

Never paint the exterior canvas or linen sizing over pipe insulation

True
False
A

false

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

The expansion bend method of accommodating piping expansion and contraction is preferred for:

a)Pneumatic installations
b)Hot water installations
c)Low pressure installations
d)High pressure installations

A

d

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

The coefficient of thermal conductivity (k) of a material is:

a)A measure of the amount of heat that will be transmitted through it
b)A high value for a good insulating material
c)Is a measurement of a material’s resistance to heat flow
d)No longer used in thermal design

A

a

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

The allowance for expansion and contraction of a piping systems is necessary because

a)the piping system requires corrosion allowance
b)the piping system must be able to accommodate design changes
c)the piping material is subjected to temperature changes
d)The piping material is covered by insulation

A

c)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Considering pipe expansion methods, compare the expansion bend method with expansion joints:

a)expansion bends have higher friction losses over a lifetime of service
b)expansion bends are higher maintenance
c)expansion bends require regular re-packing
d)Expansion bends are limited to lower temperatures

A

a

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Piping support systems must both prevent excessive pipeline sagging and:

a)Anchor piping rigidly
b)Resist vertical movement
c)Allow free movement
d)Resist piping temperature change

A

c

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Piping support requirements are prescribed by an ASME code

True
False
A

true

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

One advantage of a bellows-type corrugated expansion joint over a slip-type expansion joint:

a)Requires only packing
b)Does not require packing
c)Allows for more movement
d)Requires less space

A

b

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Slip expansion joints:

a)Must be installed in pairs
b)Must be packed and lubricated
c)Must be lubricated only
d)Are maintenance free

A

b

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

The corrugated bellows expansion joint

a)Requires the most installation space, compared to other expansion joint styles
b)Requires the least amount of maintenance, compared to other expansion joint styles
c)Accommodates the most amount of movement, compared to other expansion joint styles
d)Can be used with in the highest temperature/pressure applications, compared with other expansion joint styles

A

b

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

if only one expansion joint is used on the pipeline, it should be placed in the

a. end of the line
b. middle of the line
c. beggining of the line
d. line adjacent to the isolation valve

A

b

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

vertical adjustment of a roller stand may be obtained by means of ___________ adjustment bolts that raise or lower the roller upoen which the pipe rests

a. four
b. five
c. three
d. two

A

a

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

which of the following is not a characteristic of materials suitable for use as insulation

a. long life
b. vermin proof
c. low insulating valve
d. ability to retain its shape and insulating value when wet

A

c

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

what is the temp limit of refractory fibre insulation

a. 1000c
b. 1200c
c. 2250c
d. 1650c

A

d

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

The bellows type corrugated expansion joint is suitable for pressures up to:

A.500 kPa (73 psi)
B.2000 kPa (290 psi)
C.100 kPa (15 psi)
D.1500 kPa (217 psi)
E.1000 kPa (145 psi)

A

b

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Which of the following is not a characteristic of materials suitable for use as insulation?

A.Vermin proof
B.Ability to retain its shape and insulating value when wet
C.High insulating value
D.Long life
E.Corrosive

A

e

17
Q

The service temperature limit of Foamed Plastic insulation is:

A.320°C (608°F)
B.150°C (302°F)
C.454°C (850°F)
D.104°C (219°F)
E.650°C (1200°F)

A

b

18
Q

The service temperature of Reflective Metal Insulation is above:

A.1040°C (1904°F)
B.1650°C (3000°F)
C.1200°C (2192°F)
D.2250°C (4082°F)
E.1000°C (1832°F)

A

a

19
Q

If only one expansion joint is used in the pipeline, it should be placed in the:

A.End of the line
B.Middle of the line
C.Line adjacent to the isolation valve
D.Perpendicular to the line
E.Beginning of the line

A

b

20
Q

The service temperature limit of Mineral Fibre (Rock and Slag Wool) insulation is:

A.454°C (850°F)
B.650°C (1200°F)
C.104°C (219°F)
D.1038°C (1900°F)
E.320°C (608°F)

A

d

21
Q

The slip expansion joint is suitable for:

A.Low and medium temperatures
B.Low and high pressures
C.Medium and high pressures
D.Medium and high temperatures
E.Low and medium pressures

A

e

22
Q

The service temperature limit of Magnesia (85%) pipe insulation is:

A.1038°C (1900°F)
B.454°C (850°F)
C.320°C (608°F)
D.104°C (219°F)
E.650°C (1200°F)

A

c

23
Q

The service temperature limit of Glass Fibre insulation is:

A.454°C (850°F)
B.320°C (608°F)
C.104°C (219°F)
D.650°C (1200°F)
E.1038°C (1900°F)

A

a

24
Q

Piping must be supported:

A.To carry the weight of the fluid contained within the pipe
B.To allow the pipe to sag freely
C.To prevent free movement of the pipe due to expansion or contraction
D.And does not have to carry the weight of the pipe, valves, fittings, and insulation
E.To allow its weight to be carried by the equipment to which it is attached

A

a