CCNA 1 v7.0 Final Exam

Question 1

Refer to the exhibit. What will router R1 do with a packet that has a destination IPv6 address of 2001:db8:cafe:5::1?

forward the packet out GigabitEthernet0/0
drop the packet
forward the packet out GigabitEthernet0/1
forward the packet out Serial0/0/0

Answer 1

forward the packet out Serial0/0/0

Question 2

Refer to the exhibit. Currently router R1 uses an EIGRP route learned from Branch2 to reach the 10.10.0.0/16 network. Which floating static route would create a backup route to the 10.10.0.0/16 network in the event that the link between R1 and Branch2 goes down?

ip route 10.10.0.0 255.255.0.0 Serial 0/0/0 100
ip route 10.10.0.0 255.255.0.0 209.165.200.226 100
ip route 10.10.0.0 255.255.0.0 209.165.200.225 100
ip route 10.10.0.0 255.255.0.0 209.165.200.225 50

Answer 2

ip route 10.10.0.0 255.255.0.0 209.165.200.225 100

Question 3

Refer to the exhibit. R1 was configured with the static route command ip route 209.165.200.224 255.255.255.224 S0/0/0 and consequently users on network 172.16.0.0/16 are unable to reach resources on the Internet. How should this static route be changed to allow user traffic from the LAN to reach the Internet?

Add an administrative distance of 254.
Change the destination network and mask to 0.0.0.0 0.0.0.0
Change the exit interface to S0/0/1.
Add the next-hop neighbor address of 209.165.200.226.

Answer 3

Change the destination network and mask to 0.0.0.0 0.0.0.0

Question 4

Which option shows a correctly configured IPv4 default static route?

ip route 0.0.0.0 255.255.255.0 S0/0/0
ip route 0.0.0.0 0.0.0.0 S0/0/0
ip route 0.0.0.0 255.255.255.255 S0/0/0
ip route 0.0.0.0 255.0.0.0 S0/0/0

Answer 4

ip route 0.0.0.0 0.0.0.0 S0/0/0

Question 5

Refer to the exhibit. Which static route command can be entered on R1 to forward traffic to the LAN connected to R2?

ipv6 route 2001:db8:12:10::/64 S0/0/0
ipv6 route 2001:db8:12:10::/64 S0/0/1 fe80::2
ipv6 route 2001:db8:12:10::/64 S0/0/0 fe80::2
ipv6 route 2001:db8:12:10::/64 S0/0/1 2001:db8:12:10::1

Answer 5

ipv6 route 2001:db8:12:10::/64 S0/0/1 fe80::2

Question 6

What is a method to launch a VLAN hopping attack?

introducing a rogue switch and enabling trunking
sending spoofed native VLAN information
sending spoofed IP addresses from the attacking host
flooding the switch with MAC addresses

Answer 6

introducing a rogue switch and enabling trunking

Question 7

A cybersecurity analyst is using the macof tool to evaluate configurations of switches deployed in the backbone network of an organization. Which type of LAN attack is the analyst targeting during this evaluation?

VLAN hopping
DHCP spoofing
MAC address table overflow
VLAN double-tagging

Answer 7

MAC address table overflow

Question 8

Refer to the exhibit. A network administrator is configuring a router as a DHCPv6 server. The administrator issues a show ipv6 dhcp pool command to verify the configuration. Which statement explains the reason that the number of active clients is 0?
CCNA 2 v7.0 Final Exam Answers Full - Switching, Routing and Wireless Essentials 2

The default gateway address is not provided in the pool.
No clients have communicated with the DHCPv6 server yet.
The IPv6 DHCP pool configuration has no IPv6 address range specified.
The state is not maintained by the DHCPv6 server under stateless DHCPv6 operation.

Answer 8

The state is not maintained by the DHCPv6 server under stateless DHCPv6 operation.

Question 9

Refer to the exhibit. A network administrator configured routers R1 and R2 as part of HSRP group 1. After the routers have been reloaded, a user on Host1 complained of lack of connectivity to the Internet The network administrator issued the show standby brief command on both routers to verify the HSRP operations. In addition, the administrator observed the ARP table on Host1. Which entry should be seen in the ARP table on Host1 in order to gain connectivity to the Internet?

the virtual IP address and the virtual MAC address for the HSRP group 1
the virtual IP address of the HSRP group 1 and the MAC address of R1
the virtual IP address of the HSRP group 1 and the MAC address of R2
the IP address and the MAC address of R1

Answer 9

the virtual IP address and the virtual MAC address for the HSRP group 1

Question 10

Match the forwarding characteristic to its type. (Not all options are used.)

appropriate for high performance computing
applications

error checking before forwarding

forwarding process can begin after receiving the
destination address

forwarding process only begins after receiving the
entire frame

may forward invalid frames

only forwards valid frames

cut-through:

store-and-forward:

Answer 10

cut-through:
- appropriate for high performance computing
applications
- forwarding process can begin after receiving the
destination address
- may forward invalid frames

store-and-forward:
- error checking before forwarding
- forwarding process only begins after receiving the
entire frame
- only forwards valid frames

Question 11

Which statement is correct about how a Layer 2 switch determines how to forward frames?

Frame forwarding decisions are based on MAC address and port mappings in the CAM table.
Only frames with a broadcast destination address are forwarded out all active switch ports.
Unicast frames are always forwarded regardless of the destination MAC address.
Cut-through frame forwarding ensures that invalid frames are always dropped.

Answer 11

Frame forwarding decisions are based on MAC address and port mappings in the CAM table.

Question 12

Which statement describes a result after multiple Cisco LAN switches are interconnected?

The broadcast domain expands to all switches.
One collision domain exists per switch.
There is one broadcast domain and one collision domain per switch.
Frame collisions increase on the segments connecting the switches.
Unicast frames are always forwarded regardless of the destination MAC address.

Answer 12

The broadcast domain expands to all switches.

Question 13

Match the link state to the interface and protocol status. (Not all options are used.)

disabled

Layer 1 problem

Layer 2 problem

operational

administratively down

down/down

up/disabled

up/down

up/up

Answer 13

disabled - administratively down

Layer 1 problem - down/down

Layer 2 problem - up/down

operational - up/up

Question 14

Refer to the exhibit. How is a frame sent from PCA forwarded to PCC if the MAC address table on switch SW1 is empty?

SW1 forwards the frame directly to SW2. SW2 floods the frame to all ports connected to SW2, excluding the port through which the frame entered the switch.
SW1 floods the frame on all ports on the switch, excluding the interconnected port to switch SW2 and the port through which the frame entered the switch.
SW1 floods the frame on all ports on SW1, excluding the port through which the frame entered the switch.
SW1 drops the frame because it does not know the destination MAC address.

Answer 14

SW1 floods the frame on all ports on SW1, excluding the port through which the frame entered the switch.

Question 15

An administrator is trying to remove configurations from a switch. After using the command erase startup-config and reloading the switch, the administrator finds that VLANs 10 and 100 still exist on the switch. Why were these VLANs not removed?

Because these VLANs are stored in a file that is called vlan.dat that is located in flash memory, this file must be manually deleted.
These VLANs cannot be deleted unless the switch is in VTP client mode.
These VLANs are default VLANs that cannot be removed.
These VLANs can only be removed from the switch by using the no vlan 10 and no vlan 100 commands.

Answer 15

Because these VLANs are stored in a file that is called vlan.dat that is located in flash memory, this file must be manually deleted.

Question 16

Match the description to the correct VLAN type. (Not all options are used.)

default VLAN

management VLAN

data VLANs

native VLAN

Answer 16

configured to carry user generated traffic

all switch ports are assigned to this VLAN after initial bootup of the switch

carries untagged traffic

an IP address and subnet mask are assigned to this VLAN, allowing the switch to be accessed by HTTP, Telnet, SSH, or SNMP

only accessible by the network administrator

Question 17

Refer to the exhibit. A network administrator has connected two switches together using EtherChannel technology. If STP is running, what will be the end result?

STP will block one of the redundant links.
The switches will load balance and utilize both EtherChannels to forward packets.
The resulting loop will create a broadcast storm.
Both port channels will shutdown.

Answer 17

STP will block one of the redundant links.

Question 18

What is a secure configuration option for remote access to a network device?

Configure an ACL and apply it to the VTY lines.
Configure 802.1x.
Configure SSH.
Configure Telnet.

Answer 18

Configure SSH.

Question 19

Which wireless encryption method is the most secure?

WPA2 with AES
WPA2 with TKIP
WEP
WPA

Answer 19

WPA2 with AES

Question 20

After attaching four PCs to the switch ports, configuring the SSID and setting authentication properties for a small office network, a technician successfully tests the connectivity of all PCs that are connected to the switch and WLAN. A firewall is then configured on the device prior to connecting it to the Internet. What type of network device includes all of the described features?

firewall appliance
wireless router
switch
standalone wireless access point

Answer 20

wireless router

Question 21

Refer to the exhibit. Host A has sent a packet to host B. What will be the source MAC and IP addresses on the packet when it arrives at host B?

Source MAC: 00E0.FE91.7799
Source IP: 10.1.1.10
Source MAC: 00E0.FE10.17A3
Source IP: 10.1.1.10
Source MAC: 00E0.FE10.17A3
Source IP: 192.168.1.1
Source MAC: 00E0.FE91.7799
Source IP: 10.1.1.1
Source MAC: 00E0.FE91.7799
Source IP: 192.168.1.1

Answer 21

Source MAC: 00E0.FE91.7799
Source IP: 10.1.1.10

Question 22

Refer to the exhibit. In addition to static routes directing traffic to networks 10.10.0.0/16 and 10.20.0.0/16, Router HQ is also configured with the following command:

ip route 0.0.0.0 0.0.0.0 serial 0/1/1

What is the purpose of this command?

Packets that are received from the Internet will be forwarded to one of the LANs connected to R1 or R2.
Packets with a destination network that is not 10.10.0.0/16 or is not 10.20.0.0/16 or is not a directly connected network will be forwarded to the Internet.
Packets from the 10.10.0.0/16 network will be forwarded to network 10.20.0.0/16, and packets from the 10.20.0.0/16 network will be forwarded to network 10.10.0.0/16.
Packets that are destined for networks that are not in the routing table of HQ will be dropped.

Answer 22

Packets with a destination network that is not 10.10.0.0/16 or is not 10.20.0.0/16 or is not a directly connected network will be forwarded to the Internet.

Question 23

What protocol or technology disables redundant paths to eliminate Layer 2 loops?

VTP
STP
EtherChannel
DTP

Answer 23

STP

Question 24

Refer to the exhibit. Based on the exhibited configuration and output, why is VLAN 99 missing?

because VLAN 99 is not a valid management VLAN
because there is a cabling problem on VLAN 99
because VLAN 1 is up and there can only be one management VLAN on the switch
because VLAN 99 has not yet been created

Answer 24

because VLAN 99 has not yet been created

Question 25

Which two VTP modes allow for the creation, modification, and deletion of VLANs on the local switch? (Choose two.)

client
master
distribution
slave
server
transparent

Answer 25

server
transparent

Question 26

Which three steps should be taken before moving a Cisco switch to a new VTP management domain? (Choose three.)

Configure the switch with the name of the new management domain.
Reset the VTP counters to allow the switch to synchronize with the other switches in the domain.
Configure the VTP server in the domain to recognize the BID of the new switch.
Download the VTP database from the VTP server in the new domain.
Select the correct VTP mode and version.
Reboot the switch.

Answer 26

Configure the switch with the name of the new management domain.
Select the correct VTP mode and version.
Reboot the switch.

Question 27

A network administrator is preparing the implementation of Rapid PVST+ on a production network. How are the Rapid PVST+ link types determined on the switch interfaces?

Link types can only be configured on access ports configured with a single VLAN.
Link types can only be determined if PortFast has been configured.
Link types are determined automatically.
Link types must be configured with specific port configuration commands.

Answer 27

Link types are determined automatically.

Question 28

Refer to the exhibit. All the displayed switches are Cisco 2960 switches with the same default priority and operating at the same bandwidth. Which three ports will be STP designated ports? (Choose three.)

fa0/9
fa0/13
fa0/10
fa0/20
fa0/21
fa0/11

Answer 28

fa0/13
fa0/10
fa0/21

Question 29

How will a router handle static routing differently if Cisco Express Forwarding is disabled?

It will not perform recursive lookups.
Ethernet multiaccess interfaces will require fully specified static routes to avoid routing inconsistencies.
Static routes that use an exit interface will be unnecessary.
Serial point-to-point interfaces will require fully specified static routes to avoid routing inconsistencies.

Answer 29

Ethernet multiaccess interfaces will require fully specified static routes to avoid routing inconsistencies.

Question 30

Compared with dynamic routes, what are two advantages of using static routes on a router? (Choose two.)

They improve netw​ork security.
They take less time to converge when the network topology changes.
They improve the efficiency of discovering neighboring networks.
They use fewer router resources.

Answer 30

They improve netw​ork security.
They use fewer router resources.

Question 31

Refer to the exhibit. Which route was configured as a static route to a specific network using the next-hop address?

S 10.17.2.0/24 [1/0] via 10.16.2.2
S 0.0.0.0/0 [1/0] via 10.16.2.2
S 10.17.2.0/24 is directly connected, Serial 0/0/0
C 10.16.2.0/24 is directly connected, Serial0/0/0

Answer 31

S 10.17.2.0/24 [1/0] via 10.16.2.2

Question 32

What is the effect of entering the spanning-tree portfast configuration command on a switch?

It disables an unused port.
It disables all trunk ports.
It enables portfast on a specific switch interface.
It checks the source L2 address in the Ethernet header against the sender L2 address in the ARP body.

Answer 32

It enables portfast on a specific switch interface.

Question 33

What is the IPv6 prefix that is used for link-local addresses?

FF01::/8
2001::/3
FC00::/7
FE80::/10

Answer 33

FE80::/10

Question 34

Which two statements are characteristics of routed ports on a multilayer switch? (Choose two.)​

In a switched network, they are mostly configured between switches at the core and distribution layers.
The interface vlan command has to be entered to create a VLAN on routed ports.
They support subinterfaces, like interfaces on the Cisco IOS routers.
They are used for point-to-multipoint links.
They are not associated with a particular VLAN.

Answer 34

In a switched network, they are mostly configured between switches at the core and distribution layers.
They are not associated with a particular VLAN.

Question 35

Successful inter-VLAN routing has been operating on a network with multiple VLANs across multiple switches for some time. When an inter-switch trunk link fails and Spanning Tree Protocol brings up a backup trunk link, it is reported that hosts on two VLANs can access some, but not all the network resources that could be accessed previously. Hosts on all other VLANS do not have this problem. What is the most likely cause of this problem?

The protected edge port function on the backup trunk interfaces has been disabled.
The allowed VLANs on the backup link were not configured correctly.
Dynamic Trunking Protocol on the link has failed.
Inter-VLAN routing also failed when the trunk link failed.

Answer 35

The protected edge port function on the backup trunk interfaces has been disabled.

Question 36

Which command will start the process to bundle two physical interfaces to create an EtherChannel group via LACP?

interface port-channel 2
channel-group 1 mode desirable
interface range GigabitEthernet 0/4 – 5
channel-group 2 mode auto

Answer 36

interface range GigabitEthernet 0/4 – 5

Question 37

What action takes place when a frame entering a switch has a multicast destination MAC address?

The switch will forward the frame out all ports except the incoming port.
The switch forwards the frame out of the specified port.
The switch adds a MAC address table entry mapping for the destination MAC address and the ingress port.
The switch replaces the old entry and uses the more current port.

Answer 37

The switch will forward the frame out all ports except the incoming port.

Question 38

A junior technician was adding a route to a LAN router. A traceroute to a device on the new network revealed a wrong path and unreachable status. What should be done or checked?

Verify that there is not a default route in any of the edge router routing tables.
Check the configuration on the floating static route and adjust the AD.
Create a floating static route to that network.
Check the configuration of the exit interface on the new static route.

Answer 38

Check the configuration of the exit interface on the new static route.

Question 39

Select the three PAgP channel establishment modes. (Choose three.)

auto
default
passive
desirable
extended
on

Answer 39

auto
desirable
on

Question 40

A static route has been configured on a router. However, the destination network no longer exists. What should an administrator do to remove the static route from the routing table?

Remove the route using the no ip route command.
Change the administrative distance for that route.
Change the routing metric for that route.
Nothing. The static route will go away on its own.

Answer 40

Remove the route using the no ip route command.

Question 41

Refer to the exhibit. What can be concluded about the configuration shown on R1?

R1 is configured as a DHCPv4 relay agent.
R1 is operating as a DHCPv4 server.
R1 will broadcast DHCPv4 requests on behalf of local DHCPv4 clients.
R1 will send a message to a local DHCPv4 client to contact a DHCPv4 server at 10.10.10.8.

Answer 41

R1 is configured as a DHCPv4 relay agent.

Question 42

Match the step to each switch boot sequence description. (Not all options are used.)

step 1

step 2

step 3

step 4

step 5

step 6

perform low-level CPU initialization

enter global configuration mode

execute POST

flash file system initialization

load the boot loader from ROM

load the IOS

transfer switch control to the IOS

Answer 42

perform low-level CPU initialization - step 3

execute POST - step 1

flash file system initialization - step 4

load the boot loader from ROM - step 2

load the IOS - step 5

transfer switch control to the IOS - step 6

Question 43

Refer to the exhibit. R1 has been configured as shown. However, PC1 is not able to receive an IPv4 address. What is the problem?​

The ip helper-address command was applied on the wrong interface.
R1 is not configured as a DHCPv4 server.​
A DHCP server must be installed on the same LAN as the host that is receiving the IP address.
The ip address dhcp command was not issued on the interface Gi0/1.

Answer 43

The ip helper-address command was applied on the wrong interface.

Question 44

What two default wireless router settings can affect network security? (Choose two.)

The SSID is broadcast.
MAC address filtering is enabled.
WEP encryption is enabled.
The wireless channel is automatically selected.
A well-known administrator password is set.

Answer 44

The SSID is broadcast.
A well-known administrator password is set.

Question 45

What is the common term given to SNMP log messages that are generated by network devices and sent to the SNMP server?

traps
acknowledgments
auditing
warnings

Answer 45

traps

Question 46

A network administrator is adding a new WLAN on a Cisco 3500 series WLC. Which tab should the administrator use to create a new VLAN interface to be used for the new WLAN?

WIRELESS
MANAGEMENT
CONTROLLER
WLANs

Answer 46

CONTROLLER

Question 47

A network administrator is configuring a WLAN. Why would the administrator change the default DHCP IPv4 addresses on an AP?

to restrict access to the WLAN by authorized, authenticated users only
to monitor the operation of the wireless network
to reduce outsiders intercepting data or accessing the wireless network by using a well-known address range
to reduce the risk of interference by external devices such as microwave ovens

Answer 47

to reduce outsiders intercepting data or accessing the wireless network by using a well-known address range

Question 48

Which two functions are performed by a WLC when using split media access control (MAC)? (Choose two.)

packet acknowledgments and retransmissions
frame queuing and packet prioritization
beacons and probe responses
frame translation to other protocols
association and re-association of roaming clients

Answer 48

frame translation to other protocols
association and re-association of roaming clients

Question 49

On what switch ports should BPDU guard be enabled to enhance STP stability?

all PortFast-enabled ports
only ports that are elected as designated ports
only ports that attach to a neighboring switch
all trunk ports that are not root ports

Answer 49

all PortFast-enabled ports

Question 50

Which network attack is mitigated by enabling BPDU guard?

rogue switches on a network
CAM table overflow attacks
MAC address spoofing
rogue DHCP servers on a network

Answer 50

rogue switches on a network

Question 51

Why is DHCP snooping required when using the Dynamic ARP Inspection feature?

It relies on the settings of trusted and untrusted ports set by DHCP snooping.
It uses the MAC address table to verify the default gateway IP address.
It redirects ARP requests to the DHCP server for verification.
It uses the MAC-address-to-IP-address binding database to validate an ARP packet.

Answer 51

It uses the MAC-address-to-IP-address binding database to validate an ARP packet.

Question 52

Refer to the exhibit. Router R1 has an OSPF neighbor relationship with the ISP router over the 192.168.0.32 network. The 192.168.0.36 network link should serve as a backup when the OSPF link goes down. The floating static route command ip route 0.0.0.0 0.0.0.0 S0/0/1 100 was issued on R1 and now traffic is using the backup link even when the OSPF link is up and functioning. Which change should be made to the static route command so that traffic will only use the OSPF link when it is up?​

Change the administrative distance to 120.
Add the next hop neighbor address of 192.168.0.36.
Change the destination network to 192.168.0.34.
Change the administrative distance to 1.

Answer 52

Change the administrative distance to 120.

Question 53

Refer to the exhibit. What is the metric to forward a data packet with the IPv6 destination address 2001:DB8:ACAD:E:240:BFF:FED4:9DD2?

90
128
2170112
2681856
2682112
3193856

Answer 53

2682112

Question 54

A network administrator is configuring a new Cisco switch for remote management access. Which three items must be configured on the switch for the task? (Choose three.)

IP address
VTP domain
vty lines
default VLAN
default gateway
loopback address

Answer 54

IP address
vty lines
default gateway

Question 55

Refer to the exhibit. Which statement shown in the output allows router R1 to respond to stateless DHCPv6 requests?

ipv6 nd other-config-flag​
prefix-delegation 2001:DB8:8::/48 00030001000E84244E70​
ipv6 dhcp server LAN1​
ipv6 unicast-routing
dns-server 2001:DB8:8::8​

Answer 55

ipv6 nd other-config-flag​

Question 56

Refer to the exhibit. A Layer 3 switch routes for three VLANs and connects to a router for Internet connectivity. Which two configurations would be applied to the switch? (Choose two.)

(config)# interface gigabitethernet1/1
(config-if)# switchport mode trunk

(config)# interface gigabitethernet 1/1
(config-if)# no switchport
(config-if)# ip address 192.168.1.2 255.255.255.252

(config)# interface vlan 1
(config-if)# ip address 192.168.1.2 255.255.255.0
(config-if)# no shutdown

(config)# ip routing

(config)# interface fastethernet0/4
(config-if)# switchport mode trunk

Answer 56

(config)# interface gigabitethernet 1/1
(config-if)# no switchport
(config-if)# ip address 192.168.1.2 255.255.255.252

(config)# ip routing

Question 57

A technician is troubleshooting a slow WLAN and decides to use the split-the-traffic approach. Which two parameters would have to be configured to do this? (Choose two.)

Configure the 5 GHz band for streaming multimedia and time sensitive traffic.
Configure the security mode to WPA Personal TKIP/AES for one network and WPA2 Personal AES for the other network
Configure the 2.4 GHz band for basic internet traffic that is not time sensitive.
Configure the security mode to WPA Personal TKIP/AES for both networks.
Configure a common SSID for both split networks.

Answer 57

Configure the 5 GHz band for streaming multimedia and time sensitive traffic.

Configure the 2.4 GHz band for basic internet traffic that is not time sensitive.

Question 58

A company has just switched to a new ISP. The ISP has completed and checked the connection from its site to the company. However, employees at the company are not able to access the internet. What should be done or checked?

Verify that the static route to the server is present in the routing table.
Check the configuration on the floating static route and adjust the AD.
Ensure that the old default route has been removed from the company edge routers.
Create a floating static route to that network.

Answer 58

Ensure that the old default route has been removed from the company edge routers.

Question 59

Which information does a switch use to populate the MAC address table?

the destination MAC address and the incoming port
the destination MAC address and the outgoing port
the source and destination MAC addresses and the incoming port
the source and destination MAC addresses and the outgoing port
the source MAC address and the incoming port
the source MAC address and the outgoing port

Answer 59

the source MAC address and the incoming port

Question 60

Refer to the exhibit. A network administrator is reviewing the configuration of switch S1. Which protocol has been implemented to group multiple physical ports into one logical link?

PAgP
DTP
LACP
STP

Answer 60

PAgP

Question 61

Which type of static route is configured with a greater administrative distance to provide a backup route to a route learned from a dynamic routing protocol?

floating static route
default static route
summary static route
standard static route

Answer 61

floating static route

Question 62

What action takes place when a frame entering a switch has a unicast destination MAC address appearing in the MAC address table?

The switch updates the refresh timer for the entry.
The switch forwards the frame out of the specified port.
The switch purges the entire MAC address table.
The switch replaces the old entry and uses the more current port.

Answer 62

The switch forwards the frame out of the specified port.

Question 63

The exhibit shows two PCs called PC A and PC B, two routes called R1 and R2, and two switches. PC A has the address 172.16.1.1/24 and is connected to a switch and into an interface on R1 that has the IP address 172.16.1.254. PC B has the address 172.16.2.1/24 and is connected to a switch that is connected to another interface on R1 with the IP address 172.16.2.254. The serial interface on R1 has the address 172.16.3.1 and is connected to the serial interface on R2 that has the address 172.16.3.2/24. R2 is connected to the internet cloud. Which command will create a static route on R2 in order to reach PC B?

R2(config)# ip route 172.16.2.1 255.255.255.0 172.16.3.1
R2(config)# ip route 172.16.2.0 255.255.255.0 172.16.2.254
R2(config)# ip route 172.16.2.0 255.255.255.0 172.16.3.1
R2(config)# ip route 172.16.3.0 255.255.255.0 172.16.2.254

Answer 63

R2(config)# ip route 172.16.2.0 255.255.255.0 172.16.3.1

Question 64

What protocol or technology allows data to transmit over redundant switch links?

EtherChannel
DTP
STP
VTP

Answer 64

EtherChannel

Question 65

Refer to the exhibit. Which three hosts will receive ARP requests from host A, assuming that port Fa0/4 on both switches is configured to carry traffic for multiple VLANs? (Choose three.)

host B
host C
host D
host E
host F
host G

Answer 65

host C
host D
host F

Question 66

Refer to the exhibit. The network administrator configures both switches as displayed. However, host C is unable to ping host D and host E is unable to ping host F. What action should the administrator take to enable this communication?

Associate hosts A and B with VLAN 10 instead of VLAN 1.
Configure either trunk port in the dynamic desirable mode.
Include a router in the topology.
Remove the native VLAN from the trunk.
Add the switchport nonegotiate command to the configuration of SW2.

Answer 66

Configure either trunk port in the dynamic desirable mode.

Question 67

What is the effect of entering the shutdown configuration command on a switch?

It enables BPDU guard on a specific port.
It disables an unused port.
It enables portfast on a specific switch interface.
It disables DTP on a non-trunking interface.

Answer 67

It disables an unused port.

Question 68

What would be the primary reason an attacker would launch a MAC address overflow attack?

so that the switch stops forwarding traffic
so that legitimate hosts cannot obtain a MAC address
so that the attacker can see frames that are destined for other hosts
so that the attacker can execute arbitrary code on the switch

Answer 68

so that the attacker can see frames that are destined for other hosts

Question 69

During the AAA process, when will authorization be implemented?

Immediately after successful authentication against an AAA data source
Immediately after AAA accounting and auditing receives detailed reports
Immediately after an AAA client sends authentication information to a centralized server
Immediately after the determination of which resources a user can access

Answer 69

Immediately after successful authentication against an AAA data source

Question 70

A company security policy requires that all MAC addressing be dynamically learned and added to both the MAC address table and the running configuration on each switch. Which port security configuration will accomplish this?

auto secure MAC addresses
dynamic secure MAC addresses
static secure MAC addresses
sticky secure MAC addresses

Answer 70

sticky secure MAC addresses

Question 71

Which three Wi-Fi standards operate in the 2.4GHz range of frequencies? (Choose three.)

802.11a
802.11b
802.11g
802.11n
802.11ac

Answer 71

802.11b
802.11g
802.11n

Question 72

To obtain an overview of the spanning tree status of a switched network, a network engineer issues the show spanning-tree command on a switch. Which two items of information will this command display? (Choose two.)

The root bridge BID.
The role of the ports in all VLANs.
The status of native VLAN ports.
The number of broadcasts received on each root port.
The IP address of the management VLAN interface.

Answer 72

The root bridge BID.
The role of the ports in all VLANs.

Question 73

Refer to the exhibit. Which trunk link will not forward any traffic after the root bridge election process is complete?

Trunk1
Trunk2
Trunk3
Trunk4

Answer 73

Trunk2

Question 74

Which method of IPv6 prefix assignment relies on the prefix contained in RA messages?

EUI-64
SLAAC
static
stateful DHCPv6

Answer 74

SLAAC

Question 75

Which two protocols are used to provide server-based AAA authentication? (Choose two.)

802.1x
SSH
SNMP
TACACS+
RADIUS

Answer 75

TACACS+
RADIUS

Question 76

A network administrator is configuring a WLAN. Why would the administrator disable the broadcast feature for the SSID?

to eliminate outsiders scanning for available SSIDs in the area
to reduce the risk of interference by external devices such as microwave ovens
to reduce the risk of unauthorized APs being added to the network
to provide privacy and integrity to wireless traffic by using encryption

Answer 76

to eliminate outsiders scanning for available SSIDs in the area

Question 77

Which mitigation technique would prevent rogue servers from providing false IP configuration parameters to clients?

implementing port security
turning on DHCP snooping
disabling CDP on edge ports
implementing port-security on edge ports

Answer 77

turning on DHCP snooping

Question 78

A network administrator configures the port security feature on a switch. The security policy specifies that each access port should allow up to two MAC addresses. When the maximum number of MAC addresses is reached, a frame with the unknown source MAC address is dropped and a notification is sent to the syslog server. Which security violation mode should be configured for each access port?

shutdown
restrict
warning
protect

Answer 78

restrict

Question 79

What protocol or technology defines a group of routers, one of them defined as active and another one as standby?

EtherChannel
VTP
HSRP
DTP

Answer 79

HSRP

Question 80

Refer to the exhibit. After attempting to enter the configuration that is shown in router RTA, an administrator receives an error and users on VLAN 20 report that they are unable to reach users on VLAN 30. What is causing the problem?

There is no address on Fa0/0 to use as a default gateway.
RTA is using the same subnet for VLAN 20 and VLAN 30.
Dot1q does not support subinterfaces.
The no shutdown command should have been issued on Fa0/0.20 and Fa0/0.30.

Answer 80

RTA is using the same subnet for VLAN 20 and VLAN 30.

Question 81

Which three pairs of trunking modes will establish a functional trunk link between two Cisco switches? (Choose three.)

dynamic auto - dynamic auto
access - trunk
dynamic desirable - trunk
access - dynamic auto
dynamic desirable - dynamic desirable
dynamic desirable - dynamic auto

Answer 81

dynamic desirable - trunk
dynamic desirable - dynamic desirable
dynamic desirable - dynamic auto

Question 82

A technician is configuring a router for a small company with multiple WLANs and doesn’t need the complexity of a dynamic routing protocol. What should be done or checked?

Verify that there is not a default route in any of the edge router routing tables.
Create static routes to all internal networks and a default route to the internet.
Create extra static routes to the same location with an AD of 1.
Check the statistics on the default route for oversaturation.

Answer 82

Create static routes to all internal networks and a default route to the internet.

Question 83

A company is deploying a wireless network in the distribution facility in a Boston suburb. The warehouse is quite large and it requires multiple access points to be used. Because some of the company devices still operate at 2.4GHz, the network administrator decides to deploy the 802.11g standard. Which channel assignments on the multiple access points will make sure that the wireless channels are not overlapping?

channels 1, 5, and 9
channels 1, 6, and 11
channels 1, 7, and 13
channels 2, 6, and 10

Answer 83

channels 1, 6, and 11

Question 84

A network administrator of a small advertising company is configuring WLAN security by using the WPA2 PSK method. Which credential do office users need in order to connect their laptops to the WLAN?

the company username and password through Active Directory service
a key that matches the key on the AP
a user passphrase
a username and password configured on the AP

Answer 84

a key that matches the key on the AP

Question 85

Refer to the exhibit. What are the possible port roles for ports A, B, C, and D in this RSTP-enabled network?

alternate, designated, root, root
designated, alternate, root, root
alternate, root, designated, root
designated, root, alternate, root

Answer 85

alternate, designated, root, root

Question 86

Refer to the exhibit. Which static route would an IT technician enter to create a backup route to the 172.16.1.0 network that is only used if the primary RIP learned route fails?

ip route 172.16.1.0 255.255.255.0 s0/0/0
ip route 172.16.1.0 255.255.255.0 s0/0/0 121
ip route 172.16.1.0 255.255.255.0 s0/0/0 111
ip route 172.16.1.0 255.255.255.0 s0/0/0 91

Answer 86

ip route 172.16.1.0 255.255.255.0 s0/0/0 121

Question 87

What mitigation plan is best for thwarting a DoS attack that is creating a MAC address table overflow?

Disable DTP.
Disable STP.
Enable port security.
Place unused ports in an unused VLAN.

Answer 87

Enable port security.

Question 88

A network engineer is troubleshooting a newly deployed wireless network that is using the latest 802.11 standards. When users access high bandwidth services such as streaming video, the wireless network performance is poor. To improve performance the network engineer decides to configure a 5 Ghz frequency band SSID and train users to use that SSID for streaming media services. Why might this solution improve the wireless network performance for that type of service?

Requiring the users to switch to the 5 GHz band for streaming media is inconvenient and will result in fewer users accessing these services.
The 5 GHz band has more channels and is less crowded than the 2.4 GHz band, which makes it more suited to streaming multimedia.
The 5 GHz band has a greater range and is therefore likely to be interference-free.
The only users that can switch to the 5 GHz band will be those with the latest wireless NICs, which will reduce usage.

Answer 88

The 5 GHz band has more channels and is less crowded than the 2.4 GHz band, which makes it more suited to streaming multimedia.

Question 89

Which DHCPv4 message will a client send to accept an IPv4 address that is offered by a DHCP server?

broadcast DHCPACK
broadcast DHCPREQUEST
unicast DHCPACK
unicast DHCPREQUEST

Answer 89

broadcast DHCPREQUEST

Question 90

Refer to the exhibit. Which destination MAC address is used when frames are sent from the workstation to the default gateway?

MAC address of the virtual router
MAC address of the standby router
MAC addresses of both the forwarding and standby routers
MAC address of the forwarding router

Answer 90

MAC address of the virtual router

Question 91

After a host has generated an IPv6 address by using the DHCPv6 or SLAAC process, how does the host verify that the address is unique and therefore usable?

The host sends an ICMPv6 echo request message to the DHCPv6 or SLAAC-learned address and if no reply is returned, the address is considered unique.
The host sends an ICMPv6 neighbor solicitation message to the DHCP or SLAAC-learned address and if no neighbor advertisement is returned, the address is considered unique.
The host checks the local neighbor cache for the learned address and if the address is not cached, it it considered unique.
The host sends an ARP broadcast to the local link and if no hosts send a reply, the address is considered unique.

Answer 91

The host sends an ICMPv6 neighbor solicitation message to the DHCP or SLAAC-learned address and if no neighbor advertisement is returned, the address is considered unique.

Question 92

Match the purpose with its DHCP message type. (Not all options are used.)

a message that is used to locate any available DHCP server on a network

a message that is used to identify the explicit server and lease offer to accept

a message that is used to acknowledge that the lease is successful

a message that is used to suggest a lease to client

DHCPREQUEST

DHCPDISCOVER

DHCPNAK

DHCPOFFER

DHCPACK

Answer 92

a message that is used to identify the explicit server and lease offer to accept - DHCPREQUEST

a message that is used to locate any available DHCP server on a network - DHCPDISCOVER

a message that is used to suggest a lease to client - DHCPOFFER

a message that is used to acknowledge that the lease is successful - DHCPACK

Question 93

Which protocol adds security to remote connections?

FTP
HTTP
NetBEUI
POP
SSH

Answer 93

SSH

Question 94

Refer to the exhibit. A network administrator is verifying the configuration of inter-VLAN routing. Users complain that PC2 cannot communicate with PC1. Based on the output, what is the possible cause of the problem?

Gi0/0 is not configured as a trunk port.
The command interface GigabitEthernet0/0.5 was entered incorrectly.
There is no IP address configured on the interface Gi0/0.
The no shutdown command is not entered on subinterfaces.
The encapsulation dot1Q 5 command contains the wrong VLAN.

Answer 94

The encapsulation dot1Q 5 command contains the wrong VLAN.

Question 95

Refer to the exhibit. A network administrator is configuring inter-VLAN routing on a network. For now, only one VLAN is being used, but more will be added soon. What is the missing parameter that is shown as the highlighted question mark in the graphic?

It identifies the subinterface.
It identifies the VLAN number.
It identifies the native VLAN number.
It identifies the type of encapsulation that is used.
It identifies the number of hosts that are allowed on the interface.

Answer 95

It identifies the VLAN number.

Question 96

Match each DHCP message type with its description. (Not all options are used.)

DHCPACK

DHCPREQUEST

DHCPNACK

DHCPDISCOVER

DHCPOFFER

a client initiating a message to find a DHCP server

a DHCP server responding to the initial request by a client

the client accepting the IP address provided by the DHCP server

the DHCP server confirming that the address lease has been accepted

Answer 96

a client initiating a message to find a DHCP server - DHCPDISCOVER

a DHCP server responding to the initial request by a client - DHCPOFFER

the client accepting the IP address provided by the DHCP server - DHCPREQUEST

the DHCP server confirming that the address lease has been accepted - DHCPACK

Question 97

What network attack seeks to create a DoS for clients by preventing them from being able to obtain a DHCP lease?

IP address spoofing
DHCP starvation
CAM table attack
DHCP spoofing

Answer 97

DHCP starvation

Question 98

Refer to the exhibit. If the IP addresses of the default gateway router and the DNS server are correct, what is the configuration problem?

The DNS server and the default gateway router should be in the same subnet.
The IP address of the default gateway router is not contained in the excluded address list.
The default-router and dns-server commands need to be configured with subnet masks.
The IP address of the DNS server is not contained in the excluded address list.

Answer 98

The IP address of the default gateway router is not contained in the excluded address list.

Question 99

Refer to the exhibit. A network administrator has added a new subnet to the network and needs hosts on that subnet to receive IPv4 addresses from the DHCPv4 server.
What two commands will allow hosts on the new subnet to receive addresses from the DHCP4 server? (Choose two.)

R1(config-if)# ip helper-address 10.2.0.250
R1(config)# interface G0/1
R1(config)# interface G0/0
R2(config-if)# ip helper-address 10.2.0.250
R2(config)# interface G0/0
R1(config-if)# ip helper-address 10.1.0.254

Answer 99

R1(config-if)# ip helper-address 10.2.0.250
R1(config)# interface G0/0

Question 100

What protocol or technology uses source IP to destination IP as a load-balancing mechanism?

VTP
EtherChannel
DTP
STP

Answer 100

EtherChannel

Question 101

What protocol should be disabled to help mitigate VLAN attacks?

CDP
ARP
STP
DTP

Answer 101

DTP

Question 102

What protocol or technology requires switches to be in server mode or client mode?

EtherChannel
STP
VTP
DTP

Answer 102

VTP

Question 103

What are two reasons a network administrator would segment a network with a Layer 2 switch? (Choose two.)

to create fewer collision domains
to enhance user bandwidth
to create more broadcast domains
to eliminate virtual circuits
to isolate traffic between segments
to isolate ARP request messages from the rest of the network

Answer 103

to enhance user bandwidth
to isolate traffic between segments

Question 104

What command will enable a router to begin sending messages that allow it to configure a link-local address without using an IPv6 DHCP server?

a static route
the ipv6 route ::/0 command
the ipv6 unicast-routing command
the ip routing command

Answer 104

the ipv6 unicast-routing command

Question 105

A network administrator is using the router-on-a-stick model to configure a switch and a router for inter-VLAN routing. What configuration should be made on the switch port that connects to the router?

Configure it as a trunk port and allow only untagged traffic.
Configure the port as an access port and a member of VLAN1.
Configure the port as an 802.1q trunk port.
Configure the port as a trunk port and assign it to VLAN1.

Answer 105

Configure the port as an 802.1q trunk port.

Question 106

What are three techniques for mitigating VLAN attacks? (Choose three.)

Use private VLANs.
Enable BPDU guard.
Enable trunking manually
Enable Source Guard.
Disable DTP.
Set the native VLAN to an unused VLAN.

Answer 106

Enable trunking manually
Disable DTP.
Set the native VLAN to an unused VLAN.

Question 107

Match the DHCP message types to the order of the DHCPv4 process. (Not all options are used.)

Step 1

Step 2

Step 3

Step 4

DHCPACK

DHCPREQUEST

DHCPDISCOVER

DHCPREPLY

DHCPINFORMATION-REQUEST

DHCPOFFER

Answer 107

DHCPACK - Step 4

DHCPREQUEST - Step 3

DHCPDISCOVER - Step 1

DHCPOFFER - Step 2

Question 108

In which situation would a technician use the show interfaces switch command?

to determine if remote access is enabled
when packets are being dropped from a particular directly attached host
when an end device can reach local devices, but not remote devices
to determine the MAC address of a directly attached network device on a particular interface

Answer 108

when packets are being dropped from a particular directly attached host

Question 109

What is a drawback of the local database method of securing device access that can be solved by using AAA with centralized servers?

There is no ability to provide accountability.
User accounts must be configured locally on each device, which is an unscalable authentication solution.
It is very susceptible to brute-force attacks because there is no username.
The passwords can only be stored in plain text in the running configuration.

Answer 109

User accounts must be configured locally on each device, which is an unscalable authentication solution.

Question 110

What action does a DHCPv4 client take if it receives more than one DHCPOFFER from multiple DHCP servers?

It sends a DHCPREQUEST that identifies which lease offer the client is accepting.
It sends a DHCPNAK and begins the DHCP process over again.
It discards both offers and sends a new DHCPDISCOVER.
It accepts both DHCPOFFER messages and sends a DHCPACK.

Answer 110

It sends a DHCPREQUEST that identifies which lease offer the client is accepting.

Question 111

Refer to the exhibit. The network administrator is configuring the port security feature on switch SWC. The administrator issued the command show port-security interface fa 0/2 to verify the configuration. What can be concluded from the output that is shown? (Choose three.)

Three security violations have been detected on this interface.
This port is currently up.
The port is configured as a trunk link.
Security violations will cause this port to shut down immediately.
There is no device currently connected to this port.
The switch port mode for this interface is access mode.

Answer 111

This port is currently up.
Security violations will cause this port to shut down immediately.
The switch port mode for this interface is access mode.

Question 112

What method of wireless authentication is dependent on a RADIUS authentication server?

WEP
WPA Personal
WPA2 Personal
WPA2 Enterprise

Answer 112

WPA2 Enterprise

Question 113

A network administrator has found a user sending a double-tagged 802.1Q frame to a switch. What is the best solution to prevent this type of attack?

The native VLAN number used on any trunk should be one of the active data VLANs.
The VLANs for user access ports should be different VLANs than any native VLANs used on trunk ports.
Trunk ports should be configured with port security.
Trunk ports should use the default VLAN as the native VLAN number.

Answer 113

The VLANs for user access ports should be different VLANs than any native VLANs used on trunk ports.

Question 114

Refer to the exhibit. Which two conclusions can be drawn from the output? (Choose two.)

The EtherChannel is down.
The port channel ID is 2.
The port channel is a Layer 3 channel.
The bundle is fully operational.
The load-balancing method used is source port to destination port.

Answer 114

The EtherChannel is down.
The port channel ID is 2.

Question 115

Match the step number to the sequence of stages that occur during the HSRP failover process. (Not all options are used.)

Step 1

Step 2

Step 3

The standby router assumes the role of the forwarding router using both the IP and MAC addresses of the virtual router.

The standby router stops seeing hello messages from the forwarding router.

The forwarding router fails.

The host initiates an ARP request for the MAC address of the new forwarding router.

Answer 115

The standby router assumes the role of the forwarding router using both the IP and MAC addresses of the virtual router. - Step 3

The standby router stops seeing hello messages from the forwarding router. - Step 2

The forwarding router fails. - Step 1

Question 116

On a Cisco 3504 WLC Summary page ( Advanced > Summary ), which tab allows a network administrator to configure a particular WLAN with a WPA2 policy?

WLANs
SECURITY
WIRELESS
MANAGEMENT

Answer 116

WLANs

Question 117

Refer to the exhibit. A network engineer is configuring IPv6 routing on the network. Which command issued on router HQ will configure a default route to the Internet to forward packets to an IPv6 destination network that is not listed in the routing table?​

ipv6 route ::/0 serial 0/0/0
ip route 0.0.0.0 0.0.0.0 serial 0/1/1
ipv6 route ::1/0 serial 0/1/1
ipv6 route ::/0 serial 0/1/1

Answer 117

ipv6 route ::/0 serial 0/1/1

Question 118

Users are complaining of sporadic access to the internet every afternoon. What should be done or checked?

Create static routes to all internal networks and a default route to the internet.
Verify that there is not a default route in any of the edge router routing tables.
Create a floating static route to that network.
Check the statistics on the default route for oversaturation.

Answer 118

Check the statistics on the default route for oversaturation.

Question 119

What action takes place when the source MAC address of a frame entering a switch appears in the MAC address table associated with a different port?

The switch purges the entire MAC address table.
The switch replaces the old entry and uses the more current port.
The switch updates the refresh timer for the entry.
The switch forwards the frame out of the specified port.

Answer 119

The switch replaces the old entry and uses the more current port.

Question 120

A network administrator is configuring a WLAN. Why would the administrator use a WLAN controller?

to centralize management of multiple WLANs
to provide privacy and integrity to wireless traffic by using encryption
to facilitate group configuration and management of multiple WLANs through a WLC
to provide prioritized service for time-sensitive applications

Answer 120

to facilitate group configuration and management of multiple WLANs through a WLC

Question 121

A new Layer 3 switch is connected to a router and is being configured for interVLAN routing. What are three of the five steps required for the configuration? (Choose three.)
Case 7 (NEW):

creating SVI interfaces
adjusting the route metric
enabling IP routing
assigning ports to VLANs
deleting the default VLAN
assigning the ports to the native VLAN
modifying the default VLAN

Answer 121

creating SVI interfaces
enabling IP routing
assigning ports to VLANs

Question 122

Which three statements accurately describe duplex and speed settings on Cisco 2960 switches? (Choose three.)

An autonegotiation failure can result in connectivity issues.
When the speed is set to 1000 Mb/s, the switch ports will operate in full-duplex mode.
The duplex and speed settings of each switch port can be manually configured.
Enabling autonegotiation on a hub will prevent mismatched port speeds when connecting the hub to the switch.
By default, the speed is set to 100 Mb/s and the duplex mode is set to autonegotiation.
By default, the autonegotiation feature is disabled.

Answer 122

An autonegotiation failure can result in connectivity issues.
When the speed is set to 1000 Mb/s, the switch ports will operate in full-duplex mode.
The duplex and speed settings of each switch port can be manually configured.

Question 123

Refer to the exhibit. A network administrator configures R1 for inter-VLAN routing between VLAN 10 and VLAN 20. However, the devices in VLAN 10 and VLAN 20 cannot communicate. Based on the configuration in the exhibit, what is a possible cause for the problem?

A. The port Gi0/0 should be configured as trunk port.
B. The encapsulation is misconfigured on a subinterface.
C. A no shutdown command should be added in each subinterface configuration.
D. The command interface gigabitEthernet 0/0.1 is wrong.

Answer 123

B. The encapsulation is misconfigured on a subinterface.

Question 124

A network administrator uses the spanning-tree portfast bpduguard default global configuration command to enable BPDU guard on a switch. However, BPDU guard is not activated on all access ports. What is the cause of the issue?

BPDU guard needs to be activated in the interface configuration command mode.
Access ports configured with root guard cannot be configured with BPDU guard.
Access ports belong to different VLANs.
PortFast is not configured on all access ports.

Answer 124

PortFast is not configured on all access ports.

Question 125

Which two types of spanning tree protocols can cause suboptimal traffic flows because they assume only one spanning-tree instance for the entire bridged network? (Choose two.)

MSTP
RSTP
Rapid PVST+
PVST+
STP

Answer 125

RSTP
STP

Question 126

Refer to the exhibit. A network administrator is configuring the router R1 for IPv6 address assignment. Based on the partial configuration, which IPv6 global unicast address assignment scheme does the administrator intend to implement?

stateful
stateless
manual configuration
SLAAC

Answer 126

stateful

Question 127

A WLAN engineer deploys a WLC and five wireless APs using the CAPWAP protocol with the DTLS feature to secure the control plane of the network devices. While testing the wireless network, the WLAN engineer notices that data traffic is being exchanged between the WLC and the APs in plain-text and is not being encrypted. What is the most likely reason for this?

DTLS only provides data security through authentication and does not provide encryption for data moving between a wireless LAN controller (WLC) and an access point (AP).
Although DTLS is enabled by default to secure the CAPWAP control channel, it is disabled by default for the data channel.
DTLS is a protocol that only provides security between the access point (AP) and the wireless client.
Data encryption requires a DTLS license to be installed on each access point (AP) prior to being enabled on the wireless LAN controller (WLC).

Answer 127

Although DTLS is enabled by default to secure the CAPWAP control channel, it is disabled by default for the data channel.

Question 128

A new switch is to be added to an existing network in a remote office. The network administrator does not want the technicians in the remote office to be able to add new VLANs to the switch, but the switch should receive VLAN updates from the VTP domain. Which two steps must be performed to configure VTP on the new switch to meet these conditions? (Choose two.)

Configure the new switch as a VTP client.
Configure the existing VTP domain name on the new switch.
Configure an IP address on the new switch.
Configure all ports of both switches to access mode.
Enable VTP pruning.

Answer 128

Configure the new switch as a VTP client.
Configure the existing VTP domain name on the new switch.

Question 129

Refer to the exhibit. Consider that the main power has just been restored. PC3 issues a broadcast IPv4 DHCP request. To which port will SW1 forward this request?​

to Fa0/1, Fa0/2, and Fa0/3 only
to Fa0/1, Fa0/2, Fa0/3, and Fa0/4
to Fa0/1 only​
to Fa0/1, Fa0/2, and Fa0/4 only​
to Fa0/1 and Fa0/2 only

Answer 129

to Fa0/1, Fa0/2, and Fa0/3 only

Question 130

What action takes place when the source MAC address of a frame entering a switch is not in the MAC address table?

The switch forwards the frame out of the specified port.
The switch will forward the frame out all ports except the incoming port.
The switch adds the MAC address and incoming port number to the table.
The switch adds a MAC address table entry mapping for the destination MAC address and the ingress port.

Answer 130

The switch adds the MAC address and incoming port number to the table.

Question 131

Employees are unable to connect to servers on one of the internal networks. What should be done or checked?

Use the “show ip interface brief” command to see if an interface is down.
Verify that there is not a default route in any of the edge router routing tables.
Create static routes to all internal networks and a default route to the internet.
Check the statistics on the default route for oversaturation.

Answer 131

Use the “show ip interface brief” command to see if an interface is down.

Question 132

What is the effect of entering the ip dhcp snooping configuration command on a switch?

It enables DHCP snooping globally on a switch.
It enables PortFast globally on a switch.
It disables DTP negotiations on trunking ports.
It manually enables a trunk link.

Answer 132

It enables DHCP snooping globally on a switch.

Question 133

An administrator notices that large numbers of packets are being dropped on one of the branch routers. What should be done or checked?

Create static routes to all internal networks and a default route to the internet.
Create extra static routes to the same location with an AD of 1.
Check the statistics on the default route for oversaturation.
Check the routing table for a missing static route.

Answer 133

Check the routing table for a missing static route.

Question 134

What are two switch characteristics that could help alleviate network congestion? (Choose two.)

fast internal switching
large frame buffers
store-and-forward switching
low port density
frame check sequence (FCS) check

Answer 134

fast internal switching
large frame buffers

Question 135

What is a result of connecting two or more switches together?

The number of broadcast domains is increased.
The size of the broadcast domain is increased.
The number of collision domains is reduced.
The size of the collision domain is increased.

Answer 135

The size of the broadcast domain is increased.

Question 136

Branch users were able to access a site in the morning but have had no connectivity with the site since lunch time. What should be done or checked?

Verify that the static route to the server is present in the routing table.
Use the “show ip interface brief” command to see if an interface is down.
Check the configuration on the floating static route and adjust the AD.
Create a floating static route to that network.

Answer 136

Use the “show ip interface brief” command to see if an interface is down.

Question 137

What is the effect of entering the switchport port-security configuration command on a switch?

It dynamically learns the L2 address and copies it to the running configuration.
It enables port security on an interface.
It enables port security globally on the switch.
It restricts the number of discovery messages, per second, to be received on the interface.

Answer 137

It enables port security on an interface.

Question 138

A network administrator is configuring a WLAN. Why would the administrator use multiple lightweight APs?

to centralize management of multiple WLANs
to monitor the operation of the wireless network
to provide prioritized service for time-sensitive applications
to facilitate group configuration and management of multiple WLANs through a WLC

Answer 138

to facilitate group configuration and management of multiple WLANs through a WLC

Question 139

Refer to the exhibit. PC-A and PC-B are both in VLAN 60. PC-A is unable to communicate with PC-B. What is the problem?

The native VLAN should be VLAN 60.
The native VLAN is being pruned from the link.
The trunk has been configured with the switchport nonegotiate command.
The VLAN that is used by PC-A is not in the list of allowed VLANs on the trunk.

Answer 139

The VLAN that is used by PC-A is not in the list of allowed VLANs on the trunk.

Question 140

A network administrator is configuring a WLAN. Why would the administrator use RADIUS servers on the network?

to centralize management of multiple WLANs
to restrict access to the WLAN by authorized, authenticated users only
to facilitate group configuration and management of multiple WLANs through a WLC
to monitor the operation of the wireless network

Answer 140

to restrict access to the WLAN by authorized, authenticated users only

Question 141

What is the effect of entering the switchport mode access configuration command on a switch?

It enables BPDU guard on a specific port.
It manually enables a trunk link.
It disables an unused port.
It disables DTP on a non-trunking interface.

Answer 141

It disables DTP on a non-trunking interface.

Question 142

A network administrator has configured a router for stateless DHCPv6 operation. However, users report that workstations are not receiving DNS server information. Which two router configuration lines should be verified to ensure that stateless DHCPv6 service is properly configured? (Choose two.)

The domain-name line is included in the ipv6 dhcp pool section.
The dns-server line is included in the ipv6 dhcp pool section.
The ipv6 nd other-config-flag is entered for the interface that faces the LAN segment.
The address prefix line is included in the ipv6 dhcp pool section.
The ipv6 nd managed-config-flag is entered for the interface that faces the LAN segment.

Answer 142

The dns-server line is included in the ipv6 dhcp pool section.
The ipv6 nd other-config-flag is entered for the interface that faces the LAN segment.

Question 143

A network administrator is configuring a WLAN. Why would the administrator disable the broadcast feature for the SSID?

to eliminate outsiders scanning for available SSIDs in the area
to centralize management of multiple WLANs
to facilitate group configuration and management of multiple WLANs through a WLC
to provide prioritized service for time-sensitive applications

Answer 143

to eliminate outsiders scanning for available SSIDs in the area

Question 143

Refer to the exhibit. An administrator is attempting to install an IPv6 static route on router R1 to reach the network attached to router R2. After the static route command is entered, connectivity to the network is still failing. What error has been made in the static route configuration?

The next hop address is incorrect.
The interface is incorrect.
The destination network is incorrect.
The network prefix is incorrect.

Answer 143

The interface is incorrect.

Question 143

What action takes place when a frame entering a switch has a unicast destination MAC address that is not in the MAC address table?

The switch updates the refresh timer for the entry.
The switch resets the refresh timer on all MAC address table entries.
The switch replaces the old entry and uses the more current port.
The switch will forward the frame out all ports except the incoming port.

Answer 143

The switch will forward the frame out all ports except the incoming port.

Question 143

A junior technician was adding a route to a LAN router. A traceroute to a device on the new network revealed a wrong path and unreachable status. What should be done or checked?

Create a floating static route to that network.
Check the configuration on the floating static route and adjust the AD.
Check the configuration of the exit interface on the new static route.
Verify that the static route to the server is present in the routing table.

Answer 143

Check the configuration of the exit interface on the new static route.

Question 144

What is the effect of entering the ip arp inspection vlan 10 configuration command on a switch?

It specifies the maximum number of L2 addresses allowed on a port.
It enables DAI on specific switch interfaces previously configured with DHCP snooping.
It enables DHCP snooping globally on a switch.
It globally enables BPDU guard on all PortFast-enabled ports.

Answer 144

It enables DAI on specific switch interfaces previously configured with DHCP snooping.

Question 145

What protocol or technology manages trunk negotiations between switches?

VTP
EtherChannel
DTP
STP

Answer 145

DTP

Question 146

A network administrator is configuring a WLAN. Why would the administrator apply WPA2 with AES to the WLAN?

to reduce the risk of unauthorized APs being added to the network
to centralize management of multiple WLANs
to provide prioritized service for time-sensitive applications
to provide privacy and integrity to wireless traffic by using encryption

Answer 146

to provide privacy and integrity to wireless traffic by using encryption

Question 147

Users on a LAN are unable to get to a company web server but are able to get elsewhere. What should be done or checked?

Ensure that the old default route has been removed from the company edge routers.
Verify that the static route to the server is present in the routing table.
Check the configuration on the floating static route and adjust the AD.
Create a floating static route to that network.

Answer 147

Verify that the static route to the server is present in the routing table.

Question 148

What IPv6 prefix is designed for link-local communication?

2001::/3
ff00::/8
fc::/07
fe80::/10

Answer 148

fe80::/10

Question 149

What is the effect of entering the ip dhcp snooping limit rate 6 configuration command on a switch?

It displays the IP-to-MAC address associations for switch interfaces.
It enables port security globally on the switch.
It restricts the number of discovery messages, per second, to be received on the interface.
It dynamically learns the L2 address and copies it to the running configuration.

Answer 149

It restricts the number of discovery messages, per second, to be received on the interface.

Question 150

A network administrator is configuring a WLAN. Why would the administrator change the default DHCP IPv4 addresses on an AP?

to eliminate outsiders scanning for available SSIDs in the area
to reduce the risk of unauthorized APs being added to the network
to reduce outsiders intercepting data or accessing the wireless network by using a well-known address range
to reduce the risk of interference by external devices such as microwave ovens

Answer 150

to reduce outsiders intercepting data or accessing the wireless network by using a well-known address range

Question 151

What is the effect of entering the ip arp inspection validate src-mac configuration command on a switch?

It checks the source L2 address in the Ethernet header against the sender L2 address in the ARP body.
It disables all trunk ports.
It displays the IP-to-MAC address associations for switch interfaces.
It enables portfast on a specific switch interface.

Answer 151

It checks the source L2 address in the Ethernet header against the sender L2 address in the ARP body.

Question 152

What protocol or technology is a Cisco proprietary protocol that is automatically enabled on 2960 switches?

DTP
STP
VTP
EtherChannel

Answer 152

DTP

Question 153

What address and prefix length is used when configuring an IPv6 default static route?

::/0
FF02::1/8
0.0.0.0/0
::1/128

Answer 153

::/0

Question 154

What are two characteristics of Cisco Express Forwarding (CEF)? (Choose two.)

When a packet arrives on a router interface, it is forwarded to the control plane where the CPU matches the destination address with a matching routing table entry.
This is the fastest forwarding mechanism on Cisco routers and multilayer switches.
With this switching method, flow information for a packet is stored in the fast-switching cache to forward future packets to the same destination without CPU intervention.
Packets are forwarded based on information in the FIB and an adjacency table.
When a packet arrives on a router interface, it is forwarded to the control plane where the CPU searches for a match in the fast-switching cache.

Answer 154

This is the fastest forwarding mechanism on Cisco routers and multilayer switches.
Packets are forwarded based on information in the FIB and an adjacency table.

Question 155

Which term describes the role of a Cisco switch in the 802.1X port-based access control?

agent
supplicant
authenticator
authentication server

Answer 155

authenticator

Question 156

Which Cisco solution helps prevent ARP spoofing and ARP poisoning attacks?

Dynamic ARP Inspection
IP Source Guard
DHCP Snooping
Port Security

Answer 156

Dynamic ARP Inspection

Question 157

What is an advantage of PVST+?

PVST+ optimizes performance on the network through autoselection of the root bridge.
PVST+ reduces bandwidth consumption compared to traditional implementations of STP that use CST.
PVST+ requires fewer CPU cycles for all the switches in the network.
PVST+ optimizes performance on the network through load sharing.

Answer 157

PVST+ optimizes performance on the network through load sharing.

Question 158

What protocol or technology uses a standby router to assume packet-forwarding responsibility if the active router fails?

EtherChannel
DTP
HSRP
VTP

Answer 158

HSRP

Question 159

What is the effect of entering the show ip dhcp snooping binding configuration command on a switch?

It switches a trunk port to access mode.
It checks the source L2 address in the Ethernet header against the sender L2 address in the ARP body.
It restricts the number of discovery messages, per second, to be received on the interface.
It displays the IP-to-MAC address associations for switch interfaces.

Answer 159

It displays the IP-to-MAC address associations for switch interfaces.

Question 160

What action takes place when the source MAC address of a frame entering a switch is in the MAC address table?

The switch forwards the frame out of the specified port.
The switch updates the refresh timer for the entry.
The switch replaces the old entry and uses the more current port.
The switch adds a MAC address table entry for the destination MAC address and the egress port.

Answer 160

The switch updates the refresh timer for the entry.

Question 161

A small publishing company has a network design such that when a broadcast is sent on the LAN, 200 devices receive the transmitted broadcast. How can the network administrator reduce the number of devices that receive broadcast traffic?

Add more switches so that fewer devices are on a particular switch.
Replace the switches with switches that have more ports per switch. This will allow more devices on a particular switch.
Segment the LAN into smaller LANs and route between them.*
Replace at least half of the switches with hubs to reduce the size of the broadcast domain.

Answer 161

Segment the LAN into smaller LANs and route between them.

Question 162

What defines a host route on a Cisco router?

The link-local address is added automatically to the routing table as an IPv6 host route.
An IPv4 static host route configuration uses a destination IP address of a specific device and a /32 subnet mask.
A host route is designated with a C in the routing table.
A static IPv6 host route must include the interface type and the interface number of the next hop router.

Answer 162

An IPv4 static host route configuration uses a destination IP address of a specific device and a /32 subnet mask.

Question 163

What else is required when configuring an IPv6 static route using a next-hop link-local address?

administrative distance
ip address of the neighbor router
network number and subnet mask on the interface of the neighbor router
interface number and type

Answer 163

interface number and type

Question 164

A technician is configuring a wireless network for a small business using a SOHO wireless router. Which two authentication methods are used, if the router is configured with WPA2? (Choose two.)

personal
AES
TKIP
WEP
enterprise

Answer 164

personal
enterprise

Question 165

Which mitigation technique would prevent rogue servers from providing false IPv6 configuration parameters to clients?

enabling DHCPv6 Guard
enabling RA Guard
implementing port security on edge ports
disabling CDP on edge ports

Answer 165

enabling DHCPv6 Guard

Question 166

A PC has sent an RS message to an IPv6 router attached to the same network. Which two pieces of information will the router send to the client? (Choose two.)

prefix length
subnet mask in dotted decimal notation
domain name
administrative distance
prefix
DNS server IP address

Answer 166

prefix length
prefix

Question 167

While attending a conference, participants are using laptops for network connectivity. When a guest speaker attempts to connect to the network, the laptop fails to display any available wireless networks. The access point must be operating in which mode?

mixed
passive
active
open

Answer 167

active

Question 168

Which three components are combined to form a bridge ID?

extended system ID
cost
IP address
bridge priority
MAC address
port ID

Answer 168

extended system ID
bridge priority
MAC address