CAR 571 Aircraft Maintenance Requirements Flashcards
CAR 571?
Aircraft Maintenance Requirements
Maintenance Performance rules:
_____ _____ recommendations shall be used.
aircraft manufacturer
Who is responsible recording of maintenance and elementary work?
person performing the work
Approved data includes:
-TCs, STCs, LSTCs, RDCs, including approved equivalent foreign documents
-other drawings and methods approved by the minister or a delegate in conformity with the act
no person shall perform maintenance, or install a part that has undergone maintenance on the foregoing aircraft, except where the maintenance on the aircraft or part is done through?
Properly rated AMO or foreign Equivalent
Major repair or major modification report in accordance with the specifications set out in?
571 Appendix L
Specified data includes:
manufacture’s repair manual
Criteria for classifications of modifications and repairs is found in?
CAR 571 Appendix A.
Airframe specialized maintenance:
aircraft skin subjected to pressurization loads, if the damage to the skin measures 15cm (6inches) in any direction.
The following tasks constitute the specialized maintenance referred to in Section 571.04 of these regulations.
CAR 571 Schedule II
Engine Specialized Maintenance:
-re-assembly of a multi-part engine crankshaft
-re-assembly of a crankcase of a reciprocating engine equipped with a supercharger or reduction gear
-overhaul of a reciprocating engine equipped with supercharger or integral turbo
-overhaul of turbine engine or turbine engine module
NDT Specialized Maintenance can be found under?
CAR 571 Appendix K
In the case of maintenance performed in an _____-______ aircraft, the person is the owner of the aircraft.
amateur-built
In the case of maintenance on an _____ _____, the person is authorized to sign by an AMO.
aircraft part
Maintenance release phrase on the Test Flights:
“subject to satisfactory test flight”
Outstanding task phrase:
“no doubt as to the scope of the work being certified”
Instances where maintenance release is not required:
-in the case of glider/baloon
-flight training unit’s or operator’s MCM
-private operator’s operations manual
What is a standard part?
published and established, and maintained by an organization setting consensus standards or by a government agency
What is a commercial part?
-not speceifically designed for use of an aeronautical product
-failure does not adversely affect take off and landing of an A/C
Notes on Authorized Release Certificate can be found under?
STD 571 Appendix J (Form one)
Authorized release certificate can be used both?
domestically and internationally
Used parts not requiring a MR:
-under a special C of A in the amateur-built or owner mtce classification
-part removed from ac to ac with ‘no intervening storage period’
MR still required for the actual WP
Installation and disposal of Life-Limited parts:
-part must have a “complete history of time in service” (no. of hrs, cycles, landings, calendar time)
TC issued Airworthiness Notice No. C010 _____ _____ ______ ______ to clarify m.tce procedures following work that disturbs engine or flight controls
Inspection of Control systems
Regardless of who signs the independent check or dual inspections, the ________ _________ specifies that the person signing the maintenance release assumes full responsibility for the satisfactory completion of the work.
AN(Airworthiness Notice)
Work is performed on an altimeter or pitot-static system, the leak check outlined in?
CAR 571 Appendix B
unpressurized aircraft - with the static system evacuated to give an altimeter reading of 1000ft above the aircraft elevation, the loss of indicated altitude must not exceed ________/minute.
100ft/min
Pressurized aircraft - with the static pressure system evacuated to the maximum cabin differential pressure for which the aircraft is certified, in one minute, the loss of indicated altitude must not exceed ____ of the altitude equivalent to the maximum permitted cabin differential pressure, or _____ feet, which ever is greater.
2%, 100ft
ELT testing is to be carried during the first ____ minutes of an hour for a duration of no more than five seconds.
5min
Weight and balance reports:
Any item not forming part of the type design shall be entered in an _____ _____ with it’s associated weight and moment. Also be certified by signing a ____ ____.
equipment list, Maintenance release
Which appendix is Criteria for the Classification of Modifications and Repairs
CAR 571 Appendix A
Which appendix Altimeter System Test and Inspection
CAR 571 Appendix B
Which appendix Aircraft and Weight and balance Control?
CAR 571 Appendix C
Which appendix Inspection of Aircraft Propellers?
Appendix D
Which appendix Inspection of Aircraft Wooden Components?
Appendix E
Which appendix ATC transponder test?
Appendix F
Which appendix Maintenance ELTs?
Appendix G
Which appendix Process to Evaluate Undocumented Aircraft Parts?
Appendix H
Which appendix is ‘Reserved’?
Appendix I
Which appendix Authorised Release Certificate (form 24-0078)?
Appendix J
Which appendix Training to perform Specific NDT Tasks?
Appendix K
Which appendix Conformity Certificate - Repair or Modification?
Appendix L
Which appendix On type Maintenance Training Courses?
Appendix M
How to determine who may sign a maintenance release?
“The Maintenance release must be signed by an appropriately rated AME who is authorized through the MPM of an AMO with a rating and category appropriate to the work performed.”
Specified data and Approved data conforms under AWM?
AWM Chapter 571
A major repair or a major modification shall be reported to the Minister by means of a Major Repair or Major Modification Report in accordance with the specifications set out in 571 Appendix ___ of this chapter.
L
the AN also states that for AMOs routinely performing heavy maintenance on large
aircraft, the procedures for controlling independent checks must be documented and reference in the ______?
MPM
a _____ ______ is to be signed in respect of the maintenance performed, when applicable.
maintenance release
