Building Automation II Flashcards
What type of device is used to measure the flow rate and/or total flow of fluid flowing through a pipe?
Select one:
a.
A flow meter
b.
A level switch
c.
A pressure gauge
d.
A pressure switch
A
What is used to lift wastewater to a sewer that is at a higher elevation than the lowest part of the building drain?
Select one:
a.
A drain pump
b.
A lift station
c.
A sump pump
d.
A waste pump
B
An end-of-line resistor (EOL) is a resistor installed at the far end of an initiating-device circuit (IDC) for the purpose of ? .
Select one:
a.
maintaining the proper voltage on the circuit
b.
monitoring for circuit integrity
c.
surge protection
d.
a. and b.
B
What type of security protection monitors specific points that might allow entry or exit from a secure area?
Select one:
a.
Barrier protection
b.
Point-of-entry
c.
Specific-area protection
d.
Spot protection
B
What type of security system does not require full-time surveillance or off-premise wiring?
Select one:
a.
Central station system
b.
Local security system
c.
Supervisory system
d.
Wireless system
B
What type of security system sensing device measures a weight load over a specific area?
Select one:
a.
Acoustic glass break detector
b.
Microwave detector
c.
Passive infrared detector
d.
Stress sensor
D
What access control function keeps a door unlocked for a certain amount of time after a valid authentication?
Select one:
a.
Delay period
b.
Momentary unlock
c.
Time interval
d.
Time zone
B
A(n) ? is a magnetic contact that indicates an abnormal condition for a door or barrier.
Select one:
a.
door position switch
b.
EOL
c.
piggyback
d.
SLC
A
What type of access control device is used to automatically authorize an exit from a secure area without needing credentials or causing an alarm condition?
Select one:
a.
A card reader
b.
A momentary release
c.
A request-to-exit device
d.
An electronic keypad
C
The signal gradually degrades until it is no longer useful. The limits depend on ? .
Select one:
a.
encoding
b.
the signal power
c.
the transmission medium
d.
all of the above
D
What type of networks does a VoIP system take advantage of?
Select one:
a.
BACNET®
b.
IP networks, such as the Internet and/or Intranets
c.
LonWorks®
d.
All of the above
B
CCTV systems are used primarily for ? .
Select one:
a.
in-house television programming
b.
remote process control
c.
robotics
d.
security and surveillance applications
D
What are the two types of paging systems?
I. Central-amplified system
II. High power-amplified system
III. Low power-amplified system
IV. Self-amplified system
Select one:
a.
I. and II.
b.
I. and IV.
c.
II. and III.
d.
II. and IV.
B
A(n) ? elevator is specifically intended to service a single floor or a specific group of floors.
Select one:
a.
dedicated
b.
express
c.
freight
d.
service
B
Geared traction elevators use a(n) ? , which allows for precise control of the elevator position.
Select one:
a.
drive sheave and motor
b.
emergency braking system
c.
governor
d.
worm and worm gear type reduction unit
D
What type of signal is generated by a fire alarm system?
Select one:
a.
Alarm
b.
Supervisory signal
c.
Trouble signal
d.
All of the above
D
What type of a signal indicates an abnormal condition in a fire suppression system?
Select one:
a.
Alarm signal
b.
Maintenance signal
c.
Supervisory signal
d.
Trouble signal
C
What type of signal indicates a wiring or power problem that could disable part or all of the system?
Select one:
a.
Alarm signal
b.
Maintenance signal
c.
Supervisory signal
d.
Trouble signal
D
Failure of a device to respond to a polling request or failure to send an expected update, due to an open circuit or ground fault, results in a(n) ? .
Select one:
a.
alarm signal
b.
maintenance signal
c.
supervisory signal
d.
trouble signal
D
Initiating devices can produce ? signals, depending on the type of device and how it is programmed or wired.
Select one:
a.
alarm
b.
supervisory
c.
trouble
d.
a. or b.
e.
a., b., or c.
D
Chillers, furnaces, and boilers all use a ? to operate.
Select One:
(A) Heat Exchanger
(B) Heat Source
(C) Heat
(D) Heat Pump
A
An electric ? does not use a heat exchanger.
Select One:
(A) Heat Exchanger
(B) Heat Source
(C) Heat
(D) Heat Pump
B
An air conditioner is designed to cool spaces by removing ?.
Select One:
(A) Heat Exchanger
(B) Heat Source
(C) Heat
(D) Heat Pump
C
A ? is like an air conditioner, but includes a reversing valve to allow the heat pump to either cool or heat spaces.
Select One:
(A) Heat Exchanger
(B) Heat Source
(C) Heat
(D) Heat Pump
D
? are the most energy efficient method to control fan airflow.
Select One:
(A) VFDs
(B) Notification Appliance Circuit(NAC)
(C) Signaling Line Circuit(SLC)
(D) Short Circuits
A
A ? is used to power horn and strobe devices in a fire alarm system.
Select One:
(A) VFDs
(B) Notification Appliance Circuit(NAC)
(C) Signaling Line Circuit(SLC)
(D) Short Circuits
B
A ? is used to communicate with addressable devices in a fire alarm system
Select One:
(A) VFDs
(B) Notification Appliance Circuit(NAC)
(C) Signaling Line Circuit(SLC)
(D) Short Circuits
C
Addressable and open-loop systems can both detect ?.
Select One:
(A) VFDs
(B) Notification Appliance Circuit(NAC)
(C) Signaling Line Circuit(SLC)
(D) Short Circuits
D
Non-supervised circuits cannot detect ?.
Select One:
(A) Short Circuit
(B) Motion Sensors
(C) Magnetic Contacts
(D) Close Circuit Television Systems(CCTV)
A
Cameras are not a common request to exit (REX) device. ? and pushbuttons are the most common REX device.
Select One:
(A) Short Circuit
(B) Motion Sensors
(C) Magnetic Contacts
(D) Close Circuit Television Systems(CCTV)
B
? are the most common sensor used to detect door position.
Select One:
(A) Short Circuit
(B) Motion Sensors
(C) Magnetic Contacts
(D) Close Circuit Television Systems(CCTV)
C
? are commonly used in buildings for security systems, television programming, remote process observation, and safety management. Fire monitoring is not a typical use for a CCTV system.
Select One:
(A) Short Circuit
(B) Motion Sensors
(C) Magnetic Contacts
(D) Close Circuit Television Systems(CCTV)
D
(Information about card readers and Magnetic Strips)
—–>
Some security systems use card readers. A common type of card is a magnetic stripe card. A magnetic stripe card requires insertion or swipe at the point of use. The magnetic stripe card can become damaged over time and need to be replaced.
(Information about airport security checkpoints, their purpose, and how they are set up_
—–>
Airport security checkpoints would not be considered an access control system. This is due to the large amount of human involvement in the process. Access control systems typically operate automatically. Examples of common uses for access control systems are building entry points, mass transit facilities, and secured areas.
