Wiring Implementation

Question 1

Your connecting cat 5E cables to a 110 block. In what order should you connect the wires to follow standard wiring conventions?

– White/brown, brown, white/blue, blue, white/orange, orange, white/green, green
– White/green, green, white/orange, blue, white/blue, orange, white/brown, brown
–white/orange, orange, white/green, blue, white/blue, green, white/brown, brown
– White/blue, blue, white/orange, orange, white/green, green, white/brown, brown

Answer 1

– White/blue, blue, white/orange, orange, white/green, green, white/brown, brown

Question 2

Which of the following is used to terminate the individual wires from a 25 pair or 100 pair cable using female RJ-45 ports?

– 110 block
– Patch panel
– Horizontal cross connect
– 66 block

Answer 2

– Patch panel

Question 3

When using 110 blocks for connecting Cat5 and higher data cables, which recommendation should you follow?

– Use C – five connectors
– Keep why are pairs twisted up to within one half of an inch of the connector
– Connect wires using the T568B standard
– Connect wires using the T568A standard

Answer 3

– Keep why are pairs twisted up to within one half of an inch of the connector

Question 4

You want to use the T568A standard for adding connectors to your cat five cable. Starting with pin one, which border should you use for the wires with in the connector?

– White/brown, brown, white/blue, blue, white/orange, orange, white/green, green
– White/green, green, white/orange, blue, white/blue, orange, white/brown, brown
–white/orange, orange, white/green, blue, white/blue, green, white/brown, brown
– White/blue, blue, white/orange, orange, white/green, green, white/brown, brown

Answer 4

– White/green, green, white/orange, blue, white/blue, orange, white/brown, brown

Question 5

You are making ethernet drop cables using 5E cable and RJ-45 connectors. You need to remove the plastic coating or the cable to expose the individual wires.

What tool should use?

– Cable stripper
– Punch down tool
– Butt set
– Snips

Answer 5

Cable stripper

Question 6

Which pins in my RJ-45 connector are used to transmit data when used on a 100BaseT ethernet network? Select two answers.

– Pin one
– Pin two 
– Pin three
– Pin four
– Pin five
– Pin six
– Pin seven
– Pin eight

Answer 6

– Pin one

– Pin two

Question 7

You have a network that occupies all three floors of the building. Then WAN service provider has installed the line for the WAN service into the building in a wiring closet on the main floor.

You have a second wiring closet on the main floor. You need to connect to wiring clause. Which of the following are typically used to connect the two wiring closets? Select two answer.

– Horizontal crossconnect
– 25 pair
– Demarc extension
– smark Jack
– Vertical crossconnect

Answer 7

– Horizontal crossconnect

– 25 pair

Question 8

Which of the following uses metal clips placed over plastic slots for connecting individual copper wires?

– 110 block
– 66 block
– 25 pair
– 100 pair

Answer 8

– 110 block

Question 9

Have a network that occupies both floors of the building the WAN service provider has installed the line for the WAN service into the building in a wiring closet on the main floor.

You have a second wiring closet on the second floor directly above the wiring closet that holds the demark. Which of the following term describes the closet on the second floor?

– demarc extension
– MDF
– Horizontal crossconnect
– Vertical crossconnect
– IDF

Answer 9

– IDF – intermediate distribution frame

Question 10

Which of the following describes the point where the service providers responsibility ends and the customers responsibility begins for installing and maintaining wiring and equipment?

Answer 10

demarc

Question 11

You have a network that occupies the top floor of the three story building. The WAN service provider has installed the line on the WAN service into the building in a wiring closet on the main floor.

What would you use to relocate to WAN line into a wiring closet on your floor?

– Horizontal cross connect
– 66 block
– Smart jack
– demarc extension
– 110 block

Answer 11

– demarc extension

Question 12

What tool should be used to extend network services beyond the demarc?

– Media certifier
– tone generator
–punch down tool
– Crimper

Answer 12

Punch down tool

Question 13

Which of the following methods used to create a crossover cable?

– Use that T568A standard on one connector, and on the blog convention on the other connector.
– Use the T568A standard
– Use the T568B standard on one connector, and the blog convention on the other connector
–Use the T568A standard on one connector, and the team T568B standard on the other connector
– Use the T568B standard

Answer 13

–Use the T568A standard on one connector, and the team T568B standard on the other connector

Question 14

You’re building network cables and attaching RJ– 45 connectors to each end. Which tool do you need for this task?

– Needle nose pliers
– Punch down tool
– Vampire taps
– Crimping tool

Answer 14

– Crimping tool

Question 15

You want to use the T568B standard for adding connectors to your cat five cable. Starting with pin one, which orders should you use for the wires within the connector?

– White/brown, brown, white/blue, blue, white/orange, orange, white/green, green
– White/green, green, white/orange, blue, white/blue, orange, white/brown, brown
–white/orange, orange, white/green, blue, white/blue, green, white/brown, brown
– White/blue, blue, white/orange, orange, white/green, green, white/brown, brown

Answer 15

–white/orange, orange, white/green, blue, white/blue, green, white/brown, brown

Question 16

You are preparing to attract wires in a 110 block. To connect the wires and trim off the excess at the same time.

Which of the following should you do? Select two answers.

– Use a butt set with clips
– Point the cut side of the tool toward the wire end
– Point the cut side of the tool towards the connected and the wire
– Use a punch down tool with a Notch blade
– Use a punch down tool a straight blade
– Use a butt set with jack

Answer 16

– Point the cut side of the tool toward the wire end

– Use a punch down tool with a Notch blade

Question 17

You are working with 25 pair wires and 66 blocks. You push the wires onto the 66 blocks, but now need to cut off excess end of each wiring.

What tool should you use?

– Cable stripper
– Snips
– Butt set
– Punch down tool

Answer 17

– Punch down tool

Question 18

Which of the following terms identifies the wiring closet in the basement or a ground floor that typically includes the demarcation point?

– Horizontal crossconnect
– IDF
– MDF
– 110 block
– Smart jack

Answer 18

MDF - main distribution frame

Question 19

You have a network that occupies all three floors of the building. The WAN service provider has installed the line for the WAN service into the building in a wiring closet on the main floor. You have a wiring closet on the two remaining floors directly above the wiring closet on the main floor.

What when you used to connect the wiring closet together?

– Vertical cross connect
– demarc extension
– Horizontal cross connect
– Smart jack

Answer 19

– Vertical cross connect