Welding Inspection And Certification Ch 1 Flashcards
Why is there an increasing nood for weld quality?
A safety
B economics
C less conservative design
D government regulations
E all of the above
E.All of the above
What AWS document describes the rules for the CWI certification program?
a. AWS 5.5
b. AWSDI.1
C. AWS QC-1
d. AWS 5.1
e. AWS 14.1
C. AWS QC-1
Weld quality control should begin after welding has been initiated.
A.True
B.False
B. False
What are the three welding inspector certifications covered in AWS QCI?
a. CAWI, CWI, BWI
b. CWI, CAWI, SCWI
c.SCWI, CWI, ACWI
d. Levels I, II, and III
e. None of the above
b. CWI, CAWI, SCWI
What is generally considered to be the most important quality of a welding inspector?.
a. graduation from a welding vocational program
b. an engineering degree
c. an associate degree
d. professional attitude
e. hold a certified welder certificate
D.Professional attitude
The vision requirements for a CWI are:
a. Jaeger J2 at not less than 24 in
b. Jaeger J2 at not less than 12 in
c. Jaeger J2 at not less than 12 in, with or without corrective lenses
d.the inspector cannot wear glasses
e. 20/20 vision
c. Jaeger J2 at not less than 12 in, with or without corrective lenses
The acronym “KASH” stands for:
a. knowledge, attitude, skills and habits
b. knowledge, application, skills and habits
c. knowledge, attitude, skills and honesty
d. knowledge, application, skills and honesty
e. knowledge, attitude, sincerity and honesty
a. knowledge, attitude, skills and habits
The welding inspector should have a basic understanding of:
a. welding processes
b. nondestructive testing methods
c. a and b above
d. codes and standards
e. all of the above
e. all of the above
The term used to describe a delay in the production schedule to permit inspection is:
a. NDE
b. hold point
c. pre-inspection
d. reference point
e. arc strike
b. hold point
Inspection report corrections should be made by:
a. rewriting the entire report
b. reporting the correction to the welding foreman
c. telling the welder what was done
d. ignoring the original error
e. single-line out the error, correct the error, date and initial
e. single-line out the error, correct the error, date and initial
A simple definition of ‘ethics” is:
a. using common sense and honesty
b. living by the rules
c. being fair and impartial
d. basing decisions on facts
e. all of the above
e. all of the above
For communications to be effective, it should form a ‘continuous loop’.
a. true
b. false
a. true
The welding inspector must often communicate with:
a. welders
b. supervisors
c. welding engineers
d. members of management
e. all of the above
e. all of the above
NDE personnel (other than CWIs) are typically certified to what document?
a. QC-I
b. D1.1
c. API 1104
d. SNT-TC-1A
e. certification is not needed
d. ASNT SNT-TC-1A
You must have a high school diploma to become a CWI.
a. true
b. false
b. false
The CWI exam has several parts; these are:
a. fundamentals, practical, code
b. fundamentals, basic, code
c. basic, vision test, fundamental
d. code, vision test, practical
e. none of the above
a. fundamentals, practical, code
The CWI exam requires that the Dl .1 Code be used for the open book Code test.
a. true
b. false
b. false
The CWI exam contains three parts, each two hours long.
a. true
b. false
a. true
The title of the AWS Standard, ‘A3.0’ is:
a. Filler Metal Specifications
b. Standard Welding Terms and Definitions
c. Guide to CWI Certificatioin
d. Requirements for CWI Certification
e. none of the above
b. Standard Welding Terms and Definitions
API Standard 1 104 covers the fabrication of cross-country bridges.
a. true
b. false
b. false
Some of the approved codedstandards for the open book portion of the CWI exam are AWS
Dl . I , API 1104, AWS D15 , and AWS D15.1. ?
a. true
b. false
a. true
Prior to starting a job assignment, the welding inspector should determine:
a. what code, standard, or specification applies
b. what inspections should be conducted
c. when inspections should be conducted
d. where records are maintained
e. all of the above
e. all of the above
