Traning Bulletins TOOLS

Question 1

T.B. Tools 9 2.3.2

What is the Proper fuel mixture recommended by Technical Service for the portable power saw?

Answer 1

1 1/2 small containers (4.8 fluid ounces of Partner Engine Oil) to be mixed with one gallon of fresh
gasoline.

Question 2

TB tools 9 2.3.1

the portable power saw fuel tank is sufficient for how long of continuous operation?

Answer 2

20 to 30 minutes

Question 3

TB Tools 9 4.4.1 B

What should be attached to the portable power saw carrying handle?

Answer 3

Goggles

Question 4

TB Tools 9 appB
True / False
The Sling Must Be Removed From The Saw Before Operating the Saw.

Answer 4

False

The Sling Must Be Removed From The Saw Before STARTING The Saw.

Question 5

TB Tools 27 3.3
True / False
Operators of TICs should remember to stay low and slowly scan the area. Operators
should begin at the ceiling and use a side-to-side scanning motion, slowly working their
way to the floor area. This will compensate for the narrow field of view of the TIC.

Answer 5

True

Question 6

TB tools 27 4.3

Can the TIC see through water?

Answer 6

NO

Thermal imaging will NOT see through water.

Question 7

TB Tools 27 4.4

What is the Average field of view of a TIC ?

Answer 7

Approximately 50 degrees.

Question 8

TB Tools 27, 4.5

What is the Focal point of a TIC ?

Answer 8

Approximately 3 feet from the camera lens. *Operators viewing objects within 3 feet are too close. As a result objects within 3 feet may be blurry, out of focus or featureless.

Question 9

TB Tools 27, 4.8

Are Thermal imaging cameras rated as intrinsically safe?

Answer 9

NO

Thermal imaging cameras are NOT rated as intrinsically safe.

Question 10

TB Tools 27, 5.1

When should the TIC be inspected?

Answer 10

Immediately after 0900 & 1800 roll call and after each use

Question 11

TB Tools 28, 2.

The cordless rebar cutter can be used to cut wrought iron fences up to what diameter?

Answer 11

5/8” in diameter.

It is not to be used to cut case hardened steel rods or locks.

Question 12

TB Tools 28ds1 , 3.7
The battery capacity indicator on the rebar cutter is composed of FIVE pilot lamps. When the battery is low,
the pilot lamp display will flash to alert the operator that the remaining battery capacity is
less than____ percent?

Answer 12

20%

Question 13

TB TOOLS 28 ds1, 3.8

A fully charged battery on the rebar cutter will last for approximately how many cuts?

Answer 13

Approx. 40 cuts

Question 14

TB Tools 28 ds1 , 4.1

1) The rebar cutter should be operated how often to check for defects?
2) When should the batteries be checked?

Answer 14

1)Weekly
2)Batteries should be checked at the start of each tour for charge status. A fully charged
battery should be in the tool and the spare battery kept with the charger. The charging unit pilot lamps will confirm battery status when inserted.

Question 15

TB Tools28 ds1, 4.4 , 5.1
The rebar cutter manufacturer recommends changing the hydraulic oil every ____ months. Units shall do this on ______and_____ of each year. The Tool Room will provide the
companies with the necessary hydraulic oil.

Answer 15

every 6 months on
January 1st and July 1st.
The Tool Room will provide the
companies with the necessary hydraulic oil.

Question 16

While returning from a box near 145th st. and Convent ave. you spot 2 white males walking and holding hands. How would you greet the 2 said males?

Answer 16

HEY MARTY!!!!!

Question 17

TB tools 2

On the KO curtain. How many ropes? What is the size of the ropes and How long are the ropes?

Answer 17

Four 3/8 inch diameter, 15 foot long fire-proof ropes. One at each corner of the curtain.

Question 18

TB tools 2

When is the KO curtain inspected ?

Answer 18

The KO Curtain shall be inspected weekly during MUD and after each use.
The inspection will include removing the curtain from the carrying sleeve and unfurling it. Inspect the deployment ropes, the 5 aluminum bars embedded in the curtain and all
stitching.

Question 19

TB Tools 19

What color are the “Sure Search Door Markers”?

Answer 19

DAY GLOW YELLOW

• The door markers will be issued to selected ladder COs and rescues.
• Each member shall be issued two large markers and two small markers. A reserve supply shall be carried on the apparatus.

Question 20

TB Tools 19, 3.1
The Sure Search Door Markers are placed on the outside door knob when a member or team enters an area. What does their placement indicate?

Answer 20

Their placement will indicate to others that a primary search is in progress or has been
completed in this area and that they should continue on to another area.