Tools Flashcards

1
Q

The proper wrench used to tighten a flat-edged fitting is called a:

A

Spud wrench.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

One major advantage of a compound leverage pipe wrench is:

A

Increased torque.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

When using a hacksaw, how many teeth should be in contact with the work piece?

A

Three teeth.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

With a power vise, the only safe reamer to use is a:

A

Fluted reamer.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

The type of die head used on a power threader that doesn’t require reversing in order to disengage the pipe is called:

A

Quick opening.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

A power vise:

A

Holds and turns the pipe.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

This tool would be used to center a vertical pipe rising out of the ground through a sleeve in the slab above it:

A

A plumb bob.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What substance must always be present in an acetylene cylinder?

A

Acetone

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

What is applied to the strap of a strap wrench to keep it from slipping on the work piece?

A

Powdered resin.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What wrench is best suited for turning chrome-plated pipe?

A

A friction wrench, aka a strap wrench.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What tool would you use to tighten a faucet down to the counter top behind an existing kitchen sink?

A

A basin wrench.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What is the safety device built into an acetylene cylinder?

A

A fusible link.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

The length of a standard pipe wrench is measured from where?

A

The inside of the hook jaw to the end of the handle, with the wrench fully open.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

When a plumber uses a toilet auger to clear a stoppage in a toilet bowl, what should be done first?

A

Pull the auger handle fully out of the sheath, then place the rubberized goose neck into the trap way opening.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What’s the purpose of the square hole in the reamer blade of a “Ridgid #15” pipe cutter?

A

To open or close a “B” tank valve.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

What’s the purpose of the wheels on the chain of a cast iron snap cutter?

A

They’re pressure points to break the cast iron pipe.

17
Q

Left hand threads on an acetylene fitting are usually recognizable by:

A

A line cast around the nut.

18
Q

What should you do when opening a cylinder connected to a regulator?

A

Never stand in front of the regulator.

19
Q

What type of cutter would you use to cut a vertical pipe just as it comes above the floor level?

A

An internal pipe cutter.

20
Q

If black iron pipe is to be installed in a small space, what type of wrench would you use?

A

A chain wrench.

21
Q

What tool would you use to cut 2 inch or smaller diameter carbon steel pipe?

A

Pipe cutters.

22
Q

What’s another name for T-Drilling?

A

Extracted tee.

23
Q

When using a drill press, what is the most important thing to consider?

A

The hardness of the material to determine the RPM.

24
Q

Which drawing would be referenced when exact equipment location is required?

A

Architectural drawings with the help of grid lines.

25
Q

What is the required torque and sequence for installing mechanical joint couplings?

A

Tighten evenly to 60” pounds.

26
Q

How do you replace the cutting dies on a threading machine?

A

In numerical order.