Brainscape's Knowledge GenomeTM

Browse over 1 million classes created by top students, professors, publishers, and experts.


See full index

A Level Physics > Section 6 - Electricity > Flashcards

Section 6 - Electricity Flashcards

You may prefer our related Brainscape-certified flashcards:
Physics 101 flashcards AP® Physics flashcards
1
Q

What is electric current?

A

Net flow of charged particles

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

What is the metal wire made up of?

A

A lattice of positive ions, surrounded by ‘free electrons’

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

How do ions move in a metal wire?

A

They vibrate about fixed positions

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

How do electrons move in a wire?

A

They are free to move from one ion to another

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

What happens to electrons when a battery is connected to a wire?

A

Free electrons are repelled by the negative terminal and attracted to the positive

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

What is drift velocity?

A

When a wire is connected to a battery and electrons move randomly, but in the same direction

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

At what point is there a current in a wire?

A

When electrons move in the same direction (electrons carry charge, current = flow of charge)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

How does electric current flow through liquids?

A
  • electrolyte (e.g. salt solution)

* when power supply connected, +ve ions move to -ve terminal and vice versa

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

The equation for current is found on the data sheet , what do the symbols stand for?
I= ▲Q / ▲T

A 
I= ▲Q / ▲T 
I= current (amps) 
▲Q= charge (coulombs) 
▲T= time (seconds)
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

How is the coulomb defined?

A

The quantity of electric charge that passes a point in a circuit in 1s when a current of 1A is present

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What direction does the current go in?

A

In the direction of positive charge

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

How is the ohm defined in words?

A

A conductor has resistance of 1Ω if a current of 1A flows across when a p.d. of 1V is applied

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

How is the ohm defined in an equation?

A

1Ω = 1V / 1A

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

What is Ohm’s Law?

A

provided physical conditions are constant the Current through a wire is proportional to the p.d. across it

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What are Ohmic conductors?

A

Materials that obey Ohm’s law

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

What are the charge carriers in metals?

A

Conduction electrons

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

What are the charge carriers in a salt solution?

A

Ions

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

What is the convention for the direction of a current in a circuit?

A

Positive to negative

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

What can materials be classified as in electrical terms?

A

Conductors, insulators or semiconductors

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

How is potential difference defined?

A

As the work done (or energy transfer) per unit charge

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

What is resistance caused by?

A

The repeated collisions between the charge carriers in the material with each other and with the fixed ions of the material

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

How is the resistance of any component defined?

A

The p.d. across the component / the current through it

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

How is an Ohmic conductor represented on an I-V graph?

A

A straight line through the origin

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
Q

How will an I-V graph show that a component is obeying Ohm’s Law?

A

Straight line through the origin

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
25
Q

Why does a straight line through the origin on an I-V show that Ohm’s Law is being obeyed?

A

Gradient is constant so resistance is constant - for both directions of current flow

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
26
Q

What is the I-V graph for a filament lamp?

A

A curve

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
27
Q

What does the curved graph for a filament lamp mean?

A

Resistance increases as current increases

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
28
Q

For a filament lamp, why does resistance increase as current increases?

A

The current has a heating effect

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
29
Q

What is the I-V graph for a semiconductor diode?

A

Reverse bias for a negative p.d. and forward biased p.d. of 0.6V needed before diode conducts in forward direction

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
30
Q

For which component’s graph showing I-V characteristics can the gradient be used for resistance for all values?

A

For ohmic conductors - for filament lamps and diodes, read values off the graph for R at a certain point

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
31
Q

what are diodes?

A

diodes only let current flow in one direction

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
32
Q

What is resistance proportional to, in terms of length and area?

A

Resistance of a uniform conductor is ∞ to length and 1/∞ to its cross sectional area

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
33
Q

The equation for resistivity is found on the data sheet, waht do the symbols stand for?

ρ = RA / L

A 
ρ = RA / L
ρ = resistivity (ohm meters)
R= resistance (ohms) 
A= cross sectional area (meters squared) 
L= length (m)
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
34
Q

How can resistivity be defined?

A

As numerically equal to the resistance of a sample of the material of unit length and unit cross-sectional area at a particular temperature

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
35
Q

Typical value of resistivity of copper at 20°C?

A

Good conductor - 1.7x10^-8 Ωm

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
36
Q

Typical value of resistivity of nichrome at 20°C?

A

Conductor - 1.1x10^-6 Ωm

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
37
Q

Typical value of resistivity of silicon at 20°C?

A

Semiconductor - 2.3x10^3 Ωm

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
38
Q

what is glass at 20°C?

A

Insulator - 1.0x10^12 Ωm

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
39
Q

A wire of uniform cross-section has a resistance of RΩ. What would be the resistance of a similar wire, made of the same material, but twice as long and twice the diameter?

A

1/2 RΩ

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
40
Q

A wire of uniform cross-section has a resistance of RΩ. It is drawn to three times the length, but the volume remains constant. What will be its resistance?

A

9 RΩ

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
41
Q

In general, how are resistivity and temperature of metals linked?

A

As temperature ↑, resistivity ↑

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
42
Q

What happens, in metals at high temperatures, to resistance as temperature increases?

A

Resistance increases linearly with temperature

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
43
Q

What does increased temperature mean for particles within a wire?

A

Ions vibrate faster, with greater amplitude, so it’s more difficult for the electrons to pass through the lattice (resistance ↑)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
44
Q

When can a metal become a superconductor?

A

Below its critical temperature

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
45
Q

What does it mean if a metal becomes a superconductor?

A

It loses all of its resistance

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
46
Q

Why do superconductor wires not become hot?

A

As electrons can flow through them without any transfer of energy

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
47
Q

What are the particles like in insulators at room temperature?

A

There are few free electrons available for conduction

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
48
Q

What are the particles like in insulators at high temperatures?

A

Some electrons have enough energy to ‘escape’ from their atoms and the insulator is able to conduct

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
49
Q

What happens to resistance in insulators as temperature increases?

A

Resistance decreases

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
50
Q

What is one of the best known semiconductor materials?

A

Silicon

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
51
Q

How are semiconductors at low temperatures?

A

Poor conductors

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
52
Q

What happens in semiconductors as temperature rises?

A

Electrons break free from their atoms and so it becomes a better conductor

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
53
Q

What happens when silicon reaches 150°C?

A

Breakdown occurs and it becomes permanently damaged

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
54
Q

When might a semiconductor material become permanently damaged?

A

When it reaches a certain temperature (e.g. when silicon reaches 150°C)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
55
Q

What is the relationship between temperature and resistance for semiconducting materials?

A

As temperature ↑, resistance ↓ (for many)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
56
Q

For materials where temperature ↑ as resistance ↓, what is a term that can be used to describe them?

A

They have a negative temperature coefficient of resistance (NTC)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
57
Q

What is an NTC?

A

A negative temperature coefficient of resistance so resistance decrease as temp increases.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
58
Q

What are semiconductor materials used to make?

A

Thermistors

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
59
Q

Is there a p.d. when a material is a superconductor?

A

No - as a current flows but resistance = 0

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
60
Q

When will a superconductor lose its superconductivity?

A

When it raises above its critical temperature

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
61
Q

What is electrical power?

A

The rate at which electrical energy is converted to other forms of energy

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
62
Q

What is the unit of power?

A

The watt

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
63
Q

What is 1J per second equivalent to?

A

1 W

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
64
Q

what is the equation for energy not found on the data sheet? hint it’s the easiest one

A

power = energy / time

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
65
Q

whats the equation for energy transfer?

A

energy= power X time

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
66
Q

The equations for power are found on the data sheet. what do the symbols stand for?

p=VI= I²R = V²/R

A 
p=VI= I²R = V²/R 
P= Watts 
V= voltage (volts) 
I= current ( amps) 
R= resistance (ohms)
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
67
Q

The equation for v is found on the data sheet. what do the symbols stand for?

V=W/Q

A

V=W/Q

voltage= work done (joules) / charge (coulombs)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
68
Q

What happens in terms of energy transfers when current flows through a resistor?

A

Electrical energy is transferred to heat

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
69
Q

In which direction is the conventional current?

A

The flow of positive charge

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
70
Q

In liquids, gases and semiconductors, which particles move in the direction of the conventional current?

A

Positive ions

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
71
Q

In liquids, gases and semiconductors, which way do charge carriers flow?

A

In the opposite direction to conventional charge

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
72
Q

In metals, what is the only type of charge that flows?

A

Negative - as the only charge carrier is the electrons

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
73
Q

How does the current behave in a series circuit?

A

It is the same at all points

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
74
Q

How does the current behave in a parallel circuit?

A

Current leaving and returning to the supply is the sum of the currents in the separate branches

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
75
Q

What is Kirchoff’s first law?

A

The sum of the currents flowing into any junction in a circuit is equal to the sum of currents flowing out of that junction i.e. charge is conserved

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
76
Q

What is Kirchoff’s second law?

A

Around any closed loop in a circuit, the sum of the emfs is equal to the sum of the p.d.s

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
77
Q

Explanation of Kirchoff’s second law?

A
  • we know that a coulomb gains electrical energy as it moves through each emf and loses electrical energy as it moves through each p.d.
  • after one loop of the circuit, the energy it has gained must be equal to the energy it has dissipated
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
78
Q

What does emf stand for?

A

Electromotive force

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
79
Q

If two identical lamps are connected in series, what is their brightness?

A

They are equally bright, but not as bright as if they were connected to the battery on its own

e.g. total p.d. across both = 6V, and shared between 2 = 3V each

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
80
Q

In a series circuit, what is the total p.d. equal to?

A

total p.d. across all components = sum of p.d.s across the separate components

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
81
Q

When two identical lamps are connected in parallel, what happens to their brightness?

A

Each lamp is as bright as if it were connected to the battery on its own

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
82
Q

What happens to p.d. in a parallel circuit?

A

It is the same across each branch

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
83
Q

What model of energy transfer is used to explain why p.d. is equal across all branches in parallel?

A
  • each coulomb transports all 6J of energy to the lamp
  • each lamp receives same energy as if it were connected to battery on its own
  • twice as many coulombs pass per second through the battery - so battery runs out more quickly
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
84
Q

How is electromotive force defined?

A

The energy (chemical, mechanical, thermal etc,) converted into electrical energy when unit charge (ie 1C) passes through it

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
85
Q

what are the equations for emf not found on the data sheet?

A

ϵ= I (r+R) found on data sheet

ϵ= V + v 
V = ϵ - Ir 
ϵ= e.m.f 
V= terminal pd 
v= lost volts 
I = current 
r= internal resistance
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
86
Q

What is emf and what is p.d. in any closed loop?

A

emf - supply of electrical energy

p.d. - conversion of electrical energy to other forms

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
87
Q

For cells in series, how is total emf of their combination calculated?

A

By adding their individual emfs

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
88
Q

For identical cells in parallel, how is total emf of their combination calculated?

A

Total emf is the same size as each of the cells individually

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
89
Q

how to find the e.m.f and internal resistance and emf of a cell with a current vs p.d?

A

start with V= ϵ - Ir equation
rearrange to V= -rI + ϵ
Y=mX+c
the gradient is -r and emf is the y intercept

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
90
Q

Why, for identical cells in parallel, is the total emf the same size as each of the cells individually?

A

Each charge only passes through one cell so gains energy from the single cell

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
91
Q

Why, for a combination of cells in series, is the total emf calculated by adding the individual emfs?

A

Each charge passes through each cell so gains energy from all three

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
92
Q

When resistors are in series, what is the current going through them and p.d. across them?

A

Current through each resistor is the same, and total p.d. across resistors is the sum of the p.ds across the separate resistors ie. V=V1+V2+V3

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
93
Q

The resistance in a series equation is given on the data sheet. what do the symbols stand for?

Rt=R1+R2+R3

A

Rt=R1+R2+R3
Rt= total resistance
Rnumber= resistance of that component

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
94
Q

When resistors are in parallel, what is the current going through them and p.d. across them?

A

Current in main circuit is the sum of the currents in each parallel branch, and p.d. across each resistor is the same

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
95
Q

The equation for resistors in parallel is given on the data sheet. what do the symbols stand for?
1/Rt= 1/R1 + 1/R2 + 1/R3

A 
1/Rt= 1/R1 + 1/R2 + 1/R3 
Rt= total resistance 
Rnumber= resistance of that component
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
96
Q

In a simple potential divider (two resistors in series), what happens to p.d. when resistors are identical?

A

Resistors share voltage equally

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
97
Q

In a simple potential divider (two resistors in series), one resistor has a value of 200Ω and the other 100Ω, and the emf is 6V. What is the p.d. through each resistor?

A

200Ω = 4V

100Ω = 2V

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
98
Q

Equation to calculate output and input voltage in a potential divider?

A

Vₒᵤₜ = Vᵢₙ (R₁ / R₁+R₂)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
99
Q

What components can be used as sensors in electronic circuits?

A

Thermistors and light dependant resistors

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
100
Q

As a thermistor cools, what happens to its resistance?

A

Resistance rises

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
101
Q

As an LDR receives less light, what happens to its resistance?

A

Resistance rises

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
102
Q

In a circuit diagram, what is a loop around a cell and a resistor showing?

A

They are one component; the resistor is the cells internal resistance

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
103
Q

What is emf equal to?

A

Terminal p.d. + lost volts

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
104
Q

What happens if a driver starts a car with the head-lamps on?

A

The current through the battery is so large that the ‘lost volts’ are high - even though the battery’s internal resistance is low. Terminal p.d. drops and headlights dim.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
105
Q

What is emf equal to when there is no current in a cell?

A

The terminal p.d.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
106
Q

What is terminal p.d. ?

A

The p.d. across the terminals of the cell

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
107
Q

What happens to p.d. as soon as current is drawn from the cell?

A

P.d. drops

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
108
Q

Why does p.d. drop as soon as current is drawn from the cell?

A

The cell has internal resistance

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
109
Q

What is an open circuit?

A

A circuit that is off, with no current

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
110
Q

What is the p.d. defined as?

A

The amount of electrical energy changed to other forms of energy per coulomb of charge flowing between them

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
111
Q

How can p.d. be defined using an equation?

A

p.d. = energy used by the component / charge passing

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
112
Q

What does W equal in terms of I, t and V?

A

W = ItV

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
113
Q

What is one volt?

A

The p.d. between 2 points in a circuit in which 1J of energy in converted to other forms when 1C of charge passes between them

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
114
Q

How is the unit of 1V defined?

A

1J / 1C

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
115
Q

Why is a loop drawn around E and r (battery and resistor)?

A

To show that they are one component

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
116
Q

the equation for R is given on the data sheet. what do the symbols stand for?

R=V/I

A

R=V/I
R= resistance (ohms)
V= voltage (volts)
I= current ( amps)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
117
Q

the equation for ℰ is found on the data sheet. what do the symbols stand for?

ℰ=E/Q ℰ=I(R+r)

A

ℰ=E/Q ℰ=I(R+r)
ℰ= emf (volts)
E= energy (joules)
Q= charge (coulombs)

I=current (amps)
R= circuits resistance (ohms)
r= internal resistance if the cell

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
118
Q

what three equations of emf are not found on the data sheet?

A

ℰ=V + v
ℰ=V= Ir

V=terminal pd
v= lost volts
I= current
r= internal resistance

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
119
Q

whats rms voltage and currente? whats the equation?

A

VRMS= Vmax/ root2
IRMS=Imax/root2

rms is the average felt in an ac circuit

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
120
Q

what are diodes?

A

diodes only let current flow in one direction

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
121
Q

What is current?

A

The rate of flow of charge in a circuit.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
122
Q

What are the conditions for current to pass through a circuit?

A
  • Circuit must be complete

* Source of p.d.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
123
Q

What is the unit for current?

A

Ampere (A)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
124
Q

What are charge carriers?

A

Charged particles that move around a circuit, allowing current to flow.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
125
Q

What are the charge carriers in metals?

A

Conduction electrons.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
126
Q

What are the charge carriers in a salt solution?

A

Ions.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
127
Q

What is the unit for charge?

A

Coulomb (C)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
128
Q

Which way does conventional current flow?

A

From + to - terminals.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
129
Q

Which way do electrons flow in a circuit?

A

From - to + terminals.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
130
Q

What must be remembered about the direction of current in a circuit?

A
  • Although electrons flow from - to + terminals, this is not used.
  • Conventional current is in fact considered, which flows from + to - terminals.
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
131
Q

What is the symbol for current?

A

I

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
132
Q

What is the symbol for charge?

A

Q

133
Q

What is an ampere defined by?

A

The magnetic force between two parallel wires when they carry the same current.

134
Q

What is a coulomb defined as?

A

The amount of charge that passes in 1 second if the current is 1 ampere.

135
Q

What is the equation relating charge, current and time?

A

Q = I x t

Where:
Q - Charge (C)
I - Current (A)
t - Time (s)

136
Q

What device is used to measure current and how must it be connected?

A
  • Ammeter

* Connected in series

137
Q

Why can’t current flow in an insulator?

A
  • Each electron is attached to an atom and can’t move away from the atom
  • Therefore, electrons can’t flow
138
Q

Why can current easily flow in a metallic conductor?

A
  • Most electrons are attached to an atom, but some are delocalised
  • These delocalised electrons act as charge carriers
139
Q

What is a semiconductor and why does it behave like this?

A
  • Number of charge carriers increases with temperature -> Resistance decreases and resistivity decreases.
  • This is because as temperature increases, electrons break free and act as charge carriers
140
Q

What is a pure semiconducting material called and why?

A

Intrinsic semiconductor (intrinsic means natural) -> Conduction is due to electrons that break free from atoms of the material

141
Q

What are the uses of semiconductors?

A

Sensors for detecting changes in the environment (e.g. thermistors and diodes).

142
Q

Give two examples of semiconductors.

A

Thermistors and diodes.

143
Q

What must be done in order to make electric charge flow through a conductor?

A

Do work on it.

144
Q

What is potential difference?

A

The work done (or energy transferred) per unit charge.

145
Q

What is the unit for potential difference?

A

Volt (V)

146
Q

What is the equation relating potential difference, work done and charge?

A

V = W / Q

Where:
V - Potential difference (V)
W - Work done (J)
Q - Charge (C)

147
Q

What is the symbol for potential difference?

A

V

148
Q

What device is used to measure potential difference and how must it be connected?

A
  • Voltmeter

* In parallel

149
Q

Describe the energy changes to an electron in a circuit.

A
  • A battery transfers chemical energy to the electrons
  • Each electron has to do work to pass through a component and transfers energy to it
  • The battery resupplies electrons with energy
150
Q

When a electron passes through a component, the work done by the electron is equal to…

A

The loss of energy.

151
Q

Describe what potential difference is in terms of a electrons passing through a component.

A
  • Each electrons has to do work to pass through a component (this is equal to the energy it loses)
  • The potential difference across a component is the work done per unit charge
152
Q

What is a volt?

A
  • The potential difference across a component is 1 volt when you convert 1 joule of energy moving 1 coulomb of charge through the component.
  • 1V = 1J/C
153
Q

Describe and explain the energy changes in an electrical heater.

A
  • Heater has high resistance
  • Charge carriers collide repeatedly with atoms in the device and transfer Ek to them
  • Atoms vibrate faster
  • Resistor heats up -> Transferred as thermal energy
154
Q

Describe and explain the energy changes in an electric motor.

A
  • Work done on motor = Energy transferred to the load and surroundings -> Constant speed
  • Electrons need to be forced through the wires of the spinning motor coil against the opposing force exerted by the magnetic field.
155
Q

Describe and explain the energy changes in a loudspeaker.

A
  • Work done is transferred as sound energy.
  • Electrons need to be forced through the wires of the speaker coil against the force on them due to the loudspeaker magnet.
156
Q

For a particular potential difference across a component, what determines the current?

A

The resistance of the component.

157
Q

What is resistance?

A

A measure of how difficult it is for current to pass through the component.

158
Q

What is the unit for resistance?

A

Ohms (Ω)

159
Q

What is the symbol for resistance?

A

R

160
Q

What equation relates potential difference, current and resistance?

A

V = I x R

Where:
V - Potential difference (V)
I - Current (A)
R - Resistance (Ω)

161
Q

What is an ohm?

A

A component has a resistance of 1Ω if a potential difference of 1V makes a current of 1A flow through it.

162
Q

What an the resistance of a voltmeter and ammeter be assumed to be?

A

Voltmeter - Infinite

Ammeter - Zero

163
Q

What is Ohm’s law?

A
  • Provided that the physical conditions (e.g. temperature) remain constant, the current through an ohmic conductor us directly proportional to the potential difference across it.
  • V = I x R
164
Q

What causes resistance?

A

Repeated collisions between the charge carriers in the material with each other and the fixed ions in the material.

165
Q

What is an ohmic conductor?

A
  • A material or component that obeys Ohm’s law.

* Has constant resistance, regardless of the current.

166
Q

Describe the I/V graph for an ohmic conductor.

A
  • Goes through the origin

* Straight line

167
Q

Name two physical factors that could affect Ohm’s law.

A
  • Light level

* Temperature

168
Q

What conditions must be met for Ohm’s law?

A
  • Ohmic conductor

* Constant physical conditions

169
Q

Why must light levels and temperature be kept constant in experiments on ohmic conductors?

A

They could affect the resistance of the conductor.

170
Q

Are most components ohmic conductors?

A

No, most are non-ohmic components and have their own I-V graph.

171
Q

What does the term “I/V characteristic” refer to?

A
  • A graph of I (y-axis) against V (x-axis)

* Shows how current through a component changes as the potential difference is increased.

172
Q

On an I/V graph, what is on the x-axis?

A

V

173
Q

On a V/I graph, what is on the x-axis?

A

I

174
Q

Describe the circuit that can be used to determine the I/V graph for a component.

A
  • Ammeter
  • Component
  • Voltmeter (across component)
  • Variable resistor
  • Battery
175
Q

How can you find the resistance at a certain point on a V/I or I/V graph?
How could you change voltage and current?

A
  • Look at the value for V and for I
  • R = V/I

Change resistance of variable resistor to change V and I.

176
Q

On an I/V graph for an ohmic conductor, what does a steep gradient signify?

A

Low resistance

177
Q

On an V/I graph for an ohmic conductor, what does a steep gradient signify?

A

High resistance

178
Q

Describe the I/V graph for a filament lamp.

This is ohmic :

A
  • Curve
  • Starts steep but gets shallower with voltage
  • Rotated around origin
179
Q

Why isn’t a filament bulb an ohmic conductor (in terms of pd and temperature and resistance)?

A

The wire heats up with current and potential difference, causing the resistance to increase.

180
Q

Explain how and why the resistance of a filament lamp changes as potential difference is increased.

A
  • As potential difference increases, so does current.
  • Increasing current means that some electrical energy is transferred into heat energy, increasing the metal’s temperature (due to electron-ion collisions).
  • Positive ions in metal vibrate more -> More difficult for charge carriers to pass -> Current can’t flow as easily -> Resistance increased
181
Q

Explain how and why the resistance of a filament lamp changes as current is increased.

A
  • Increasing current increases the temperature (due to electron-ion collisions)
  • Positive ions in metal vibrate more -> More difficult for charge carriers to pass -> Resistance increased.

IV graph levels off at high current for filament lamps.

182
Q

Compare the resistance of semiconductors and metals..

How does it vary with temperature?

A
  • Metals are better conductors (i.e. lower resistance)

* Resistance of metals increases with temperature, while resistance of semiconductors decreases with temperature

183
Q

At low temperatures, why are metals better conductors than semiconductors?

A

There are more charge carriers available.

semiconductors have electrons stuck to atoms and aren’t free moving

184
Q

What is a thermistor?

A

A resistor with a resistance that changes with temperature.

185
Q

What type of thermistor do you need to know about?

A

Negative Temperature Coefficient (NTC) - Resistance decreases as temperature increases

186
Q

How does the resistance of a thermistor change with temperature?

A

As temperature increases, resistance decreases.

187
Q

Describe the graph of resistance (y-axis) against temperature (x-axis) for a thermistor.

A
  • Downwards curve

* Gradient becomes less steep with temperature

188
Q

Describe the I/V graph for a thermistor.

A
  • Upwards curve
  • Curved upwards away from x-axis
  • Rotated around origin
189
Q

Explain the I/V graph for a thermistor.

A
  • As p.d. increases, current increases
  • This causes temperature to increase
  • More electrons have enough energy to escape from their atoms
  • More charge carriers -> Resistance decreases
  • More current can flow, so graph curves upwards
190
Q

How can you investigate the resistance of a thermistor?

A

Use water bath:

Put the thermistor into a beaker and pour boiling water into it, covering the thermistor.

Measure the temperature of the water using a digital thermometer.
Record the current through the circuit with the ammeter.

The potential difference needs to be kept constant throughout the experiment.

Keep recording current and temperature for every 5 degree drop.

From the values for current and potential difference, work out resistance for each temperature.
For NTC resistors, as temperature decreases, resistance increases (current will decrease).

191
Q

What is a diode?

A

A component that allows current to flow in one direction only
Made from semiconductors

192
Q

What is the forward bias of a diode?

A

The direction in which the current is allowed to flow.

193
Q

What does LED stand for?

A

Light emitting diode.

194
Q

Describe how the resistance of a diode changes with potential difference.

A
  • With a negative voltage (in reverse bias) the resistance is very high
  • Up to a threshold voltage (usually about 0.6V) the resistance remains high
  • After this voltage, the resistance falls rapidly
195
Q

What is the threshold voltage of most diodes?

A

About 0.6V in the forward direction before they conduct.

196
Q

What is an LED?

A

A diode that emits light when current flows through it.

197
Q

What does the triangle symbol represent on a diode?

A

triangle symbol indicates the direction the diode will let current flow.
E.g. a large current can flow left to right (forward bias):

198
Q

Describe the I/V graph for a diode.

A
  • At negative voltage -> Very small NEGATIVE current
  • At low positive voltage -> Small positive current
  • Above threshold voltage (0.6V) -> Current increases linearly (starts of curved)
199
Q

Name a use of a diode.

A

Protection of d.c. circuits.

200
Q

What is a cell?

A

A source of electrical energy.

201
Q

What is a LDR?

A
  • Light-depedent resistor

* Resistance decreases as temperature is increased.

202
Q

What is a positive temperature coefficient?

A

When resistance increases with increasing temperature.

203
Q

What is a negative temperature coefficient?

A

When resistance decreases with increasing temperature.

204
Q

Give an example of a material/component with a positive temperature coefficient.

A

Metals

205
Q

Give an example of a material/component with a negative temperature coefficient.

A

Thermistor

206
Q

What is the circuit symbol for a thermistor?

A

Rectangle with diagonal line across it, with a short line at the end.

207
Q

What is the circuit symbol for a diode?

A

Circle with a triangle and line in it.

208
Q

What is the circuit symbol for an LED?

A

Circle with a triangle and line in it. Two lines pointing away from it.

209
Q

What does the symbol for a diode in a circuit tell us?

A

Current can flow in the direction that the triangle points.

210
Q

What is the circuit symbol for a light bulb?

A

A circle with a cross in it.

211
Q

What is the circuit symbol for a resistor?

A

A rectangle.

212
Q

What is the circuit symbol for a variable resistor?

A

A rectangle with a diagonal arrow.

213
Q

What is the circuit symbol for a LDR?

A

A rectangle with two arrows pointing towards it.

214
Q

What is the circuit symbol for a heater?

A

A rectangle divided into 4 squares.

215
Q

What is the circuit symbol for an electric motor?

A

A circle with an “M” with a line under it that points down and up at either end.

216
Q

What is the resistivity of a material?

A

The resistance of a 1m length of the material of 1m2 cross-sectional area.

217
Q

What 3 factors affect the resistance of a piece of wire?

A

1) Length
2) Area (Cross-sectional)
3) Resistivity

218
Q

How does length of a wire affect its resistance?

A

The longer the wire, the higher the resistance (More difficult to make current flow through)

219
Q

How does the cross-sectional area of a wire affect its resistance?

A

The wider the wire, the lower the resistance. (Easier for electrons to pass through)

220
Q

What does resistivity measure?

A

How much a particular material resists current flow

221
Q

What factors affect the resistivity of a material?

A

Property of a material:

Structure of material and environmental factors (e.g. temperature and light intensity)

222
Q

What is the unit for resistivity?

A

Ohm-metre (Ωm)

223
Q

What is the symbol for resistivity?

A

p (Greek letter “rho”)

224
Q

What is the equation for resistivity?

A 
p = RA/L
Where:
p - Resistivity (Ωm)
R - Resistance (Ω)
A - Area (m2)
L - Length (m)
225
Q

Is the resistivity of a material a set quantity?

A
  • No, it depends on temperature.

* Resistivity is usually quoted at a set temperature (e.g. 25*)

226
Q

What is the size of a typical value for the resistivity of a conductor?
Is this good for conducting?

A

Very small - e.g. 1.72 x 10^-8 Ohm meters.

Lower resistivity = better at conducting electricity

227
Q

Describe how you can calculate the resistivity of a piece of wire.

A

Risk assessment first.

Calculate area:
1) Measure the diameter at at least 3 points along the wire using a micrometre -> Find average -> Divide by two to get radius
2) Area = πr^2
Calculate R/l:
1) Set up a circuit with an ammeter, wire and voltmeter.
2) Attach a test wire along a ruler -> Attach one end where the ruler reads 0cm
3) Move the crocodile clip at the other end to adjust the length of the wire
4) Record the length of the wire and the resistance (R = V/I)
5) Repeat this to find an average resistance for that length
6) Vary the length from 0.10 to 1.00m
7) Plot a graph of resistance (y) against length (x) + draw a line of best fit (should be straight line through origin)
Find the resistivity:
1) The gradient is R/l, so it can be subbed in to the equation p = RA/l by multiplying by the area.
2) Take note to maintain the temperature of the wire constant at all times (since resistivity depends on temperature).

228
Q

When calculating the resistivity of a piece of wire, what is it important to keep constant and how?

A
  • Temperature -> Resistivity depends on it

* Only have small currents flow through the wire

229
Q

What is the problem with most materials having some resistivity?

A

When current is passed through them, they heat up and energy is wasted as thermal energy.

230
Q

What is the easiest way to lower the resistivity of most materials?

A

Cool them down.

231
Q

What is a superconductor?

A

A wire or device made of a material that has 0 resistivity below a critical temperature, which depends on the material.

232
Q

Describe how the resistance of a superconductor changes with temperature.

A
  • Below critical temperature -> Zero resistance

* Above critical temperature -> Resistance increases

233
Q

What is the temperature below which a superconductor has no resistance called?

A

Threshold temperature / Critical temperature

234
Q

Describe how the resistance of these components varies with temperature:
• Metal
• Semiconductor
• Superconductor

A
  • Metal -> Resistance increases as temperature increases
  • Semiconductor -> Resistance decreases as temperature increases
  • Superconductor -> Non-zero resistance above critical temperature, zero resistance below it
235
Q

What are the positives of a superconductor and why?

A
  • With no resistance, there is no heating effect -> No energy lost
  • You could start a current using a magnet and it would flow forever
236
Q

What is the problem that makes the use of superconductors difficult?

A
  • Most have a transition temperature below 10 kelvin (263*C)

* It is hard and expensive to cool things that much

237
Q

What is a high-temperature superconductor?

A

A superconductor with a critical temperature above 77K (the boiling point of nitrogen).

238
Q

What is 77K the boiling point of?

A

The boiling point of nitrogen.

239
Q

Describe the graph of resistivity (y) against temperature (x) for a superconductor.

A
  • Line along the x-axis up to critical temperature
  • Vertical spike at the critical temperature
  • Straight line with upwards gradient after this
240
Q

What is the next development in terms of superconductors?

A

Room-temperature superconductors

241
Q

Give some current uses of superconductors.

A

High-power electromagnets used in:
• MRI scanners
• Particle accelerators

242
Q

Give some potential uses of superconductors.

A
  • Power cables that transmit energy without energy loss
  • Strong electromagnets without a constant power source -used in medicine and Maglev trains
  • Electronic circuits that work really fast since there’s no resistance to slow them down (therefore minimal energy loss)
243
Q

What is power?

A

The rate of transfer of energy.

244
Q

What is the symbol for power?

A

P

245
Q

What is the unit for power?

A

Watt (W)

246
Q

What is a watt?

A

1 joule transferred per second.

247
Q

What is the formula for power?

A

P = E/t

Where:
P - Power (W)
E - Energy transferred (J)
t - Time (s)

248
Q

What is the formula for power in terms of current and voltage?

A

P = I x V

249
Q

What is the formula for power in terms of resistance and voltage?

A

P = V²/R

250
Q

What is the formula for power in terms of current and resistance?

A

P = I² x R

251
Q

How can the different equations for power by derived?

A

Combining:
• P = I x V
• V = I x R

252
Q

What are the 4 equations for power?

A
  • P = E/t
  • P = I x V
  • P = V² /R
  • P = I² x R
253
Q

What is the equation for energy transferred in terms of power and time?

A

E = P x t

NOTE: Any of the equations for P can be subbed in here (e.g. E = V x I x t).

254
Q

What causes resistance?

A

Electrons colliding with atoms in the material and losing energy.

255
Q

What is internal resistance and what causes it?

A
  • The resistance of a battery itself.

* Caused by electrons colliding with the atoms in the battery.

256
Q

What causes cells and batteries to warm up when they are used?

A

Their internal resistances.

257
Q

What is the symbol for internal resistance?

A

r

258
Q

What is the name for the resistance of a cell?

A

Internal resistance

259
Q

What is load resistance?

A

The total resistance of all the components in a circuit except the battery.

260
Q

What is the symbol for load resistance?

A

R

261
Q

What is another name for load resistance?

A

External resistance

262
Q

What are the two types of resistance in a circuit?

A
  • Internal resistance (r)

* Load resistance (R)

263
Q

What does e.m.f. stand for?

A

Electromotive force

264
Q

What is e.m.f.?

A
  • The amount of electrical energy the battery produces and transfers for each coulomb of charge
  • i.e. It is the battery’s effective output voltage when no current flows through it
265
Q

What is the symbol for e.m.f.?

A

ε

266
Q

What are the units for e.m.f.?

A

Volts (V)

267
Q

What is the equation that defines e.m.f.?

A

ε = E/Q

268
Q

What is terminal p.d.?

A
  • The potential difference across the load resistance (R).

* i.e. The energy transferred per coulomb of charge flowing through the load resistance.

269
Q

What is the symbol for terminal p.d.?

A

V

270
Q

When is the terminal p.d. the same as e.m.f.?

Why is this uncommon?

A
  • If there is no internal resistance or no current flowing

* Usually energy is lost in overcoming the internal resistance

271
Q

What is the name for the energy wasted per coulomb in overcoming the internal resistance in a cell?

A

Lost volts

272
Q

What is the symbol for lost volts?

A

v

273
Q

What conservation of energy equation is used in e.m.f. calculations?

A

Energy per coulomb supplied by source (ε) = Energy per coulomb transferred in load resistance (V) + Energy per coulomb wasted in internal resistance (v)

ε = V + v

274
Q

Which e.m.f. equation are you given in the exam?

A

ε = I(R + r)

275
Q

In e.m.f. calculations, what are the different symbols?

A 
ε - emf of battery
V - Terminal pd 
v - Lost volts
R - Load resistance
r - Internal resistance 
I - Current
276
Q

Rearrange the “ε = I(R+r)” equation to give 3 more equations.

A
  • ε = I(R+r)
  • ε = V + v
  • V = ε - v
  • V = ε - Ir
277
Q

How can we find energy lost as heat (energy dissipated) when overcoming the internal resistance in a power supply?

A

P=I^2

278
Q

How can you work out the total e.m.f. of cells in series?

A
  • Add their individual e.m.f.s

* ε(total) = ε1 + ε2 + ε3 + …

279
Q

How can you work out the total e.m.f. of IDENTICAL cells in parallel?

A
  • Total e.m.f. is equal to each individual e.m.f.

* ε(total) = ε1 = ε2 = ε3 = …

280
Q

For identical cells in parallel, why is the total e.m.f of the combination of cells the same as the e.m.f of the individual cells?

A

The amount of charge flowing in the circuit doesn’t increase by adding cells in parallel.
The number of paths the charges can take does change.
The current will split equally between identical cells.
The charge only gains e.m.f from the cells it travels through - overall e.m.f in circuit doesn’t increase.

281
Q

Three identical cells with an e.m.f. of 2.0V and an internal resistance of 0.20Ω are connected in parallel. A current of 0.90A is flowing through the circuit. Calculate the total p.d. across the cells.

(See diagram of 83 of revision guide)

A 
Calculate the lost volts for 1 cell:
• I = 0.90 / 3 = 0.30A
• v = Ir = 0.30 x 0.20 = 0.06V
Find terminal pd across 1 cell:
• V = ε - v
• V = 2 - 0.06 = 1.94V
282
Q

Describe an experiment to calculate the e.m.f. and internal resistance of a cell.

A

1) Connect the cell in series with an ammeter and variable resistor + connect a voltmeter across the cell
2) Vary the current using the variable resistor - start at highest resistance (open the switch and close it again to get two more sets of I and V values and find mean)
3) Record the voltage at each current.
4) Plot a graph of voltage (y) against current (x).
5) y-intercept = ε
Gradient = -r
Make sure external factors are kept the constant like temperature.

283
Q

In the experiment to find the e.m.f. and internal resistance of a cell, how should the V and I values be plotted and why?

A 
• V = ε - Ir
Rearranges to:
• V = -rI + ε
• y = mx + c
Therefore:
• Plot V on the y and I on the x
• Gradient = -r
• y-intercept = ε
284
Q

What is an easy way to measure a cell’s e.m.f.?

A
  • Connect a high-resistance voltmeter across its terminals

* A small current flows through the voltmeter, so there are some lost volts, but this is negligible

285
Q

When connecting a high-resistance voltmeter across a cell to find its e.m.f., what is the error in the results?

A
  • Small amount of current flows through the voltmeter
  • So there are some lost volts
  • Measured value is very slightly less than the e.m.f.
  • But this is negligible
286
Q

Does charge get used up?

A

No

287
Q

What happens to charge and current at a junction?

A

They are conserved.

288
Q

What quantities are conserved at a junction?

A
  • Current

* Charge

289
Q

Is voltage conserved at a junction?

A

Not necessarily.

290
Q

What is Kirchhoff’s first law?

A

Total current entering junction = Total current leaving it

291
Q

Is energy in a circuit conserved?

A

Yes

292
Q

Energy transferred to a charge is…

A

e.m.f.

293
Q

Energy transferred from a charge is…

A

Potential difference.

294
Q

What is Kirchhoff’s second law?

A

Total e.m.f. around a series circuit = Sum of the p.d.s across each component

295
Q

Explain Kirchhoff’s second law.

A
  • e.m.f. is the energy transferred to a charge
  • p.d. is the energy transferred from a charge
  • Conservation of energy says that these two must be equal
  • Therefore: Total e.m.f. = Sum of p.d.s
296
Q

State both of Kirchhoff’s laws.

A

1) Total current entering a junction = Total current leaving it
2) Total e.m.f. around a series circuit = Sum of p.d.s across each component

297
Q

Describe current in a series circuit.

A

It is the same at all points.

298
Q

Describe e.m.f. in a series circuit.

A
  • e.m.f. is split between components

* ε = V1 + V2 + V3 + …

299
Q

Describe resistance in a series circuit.

A
  • Sum of the individual resistances gives total resistance

* R(total) = R1 + R2 + R3 + …

300
Q

Describe a series circuit in terms of:
• Current
• e.m.f.
• Resistance

A 
CURRENT:
• Same at all points
EMF:
• Shared between components
RESISTANCE:
• Total resistance is sum of the individual resistances
301
Q

Describe current in a parallel circuit.

A
  • Split between branches (at each junction)

* I(total) = I1 + I2 + I3 + …

302
Q

Describe e.m.f. in a parallel circuit.

A
  • Same p.d. on each branch
  • Within each branch, the sum of the p.d.s equals the e.m.f.
  • e.m.f. = Branch 1 = Branch 2 = Branch 3 = …
303
Q

Describe resistance in a parallel circuit.

A

1/R(total) = 1/R1 + 1/R2 + 1/R3 + …

304
Q

Describe a parallel circuit in terms of:
• Current
• e.m.f.
• Resistance

A

CURRENT:
• Split between branches (at each junction)
EMF:
• Same p.d. on each branch
• Within each branch, the sum of the p.d.s equals the e.m.f.
RESISTANCE:
• 1/R(total) = 1/R1 + 1/R2 + 1/R3 + …

305
Q

Remember to practice conservation of energy and charge questions.

A

See example pg 85 of revision guide.

306
Q

What is a potential divider?

A

A setup used to obtain an output voltage equal to a fraction of the source voltage.

307
Q

What is the simplest possible potential divider?

A

A voltage source with 2 resistors in series (with wires around one of the resistors).

308
Q

What range in potential difference can be provided by a potential divider?

A

From 0 to the source voltage.

309
Q

How is PD split in a potential divider?

A

Potential difference across the voltage source (e.g. a battery) is split across the resistors in the ratio of the resistances:
i.e. The higher the resistance, the higher the voltage across that resistor

310
Q

With a 2Ω and 3Ω resistor in series, what is the potential difference across each resistor?

A
  • 2Ω -> 2/5 of the source voltage

* 3Ω -> 3/5 of the source voltage

311
Q

What does a potential divider look like?

A
312
Q

For a source voltage, Vs, connected in series with resistors R1 and R2 (with output around R2), what equation gives the output voltage around R2?

A

V(out) = (R2 / (R1 + R2)) x Vs

i.e. Output voltage = (Output resistor voltage / Total load voltage) x Source voltage

313
Q

How do you get: V(out) = (R2 / (R1 + R2)) x Vs

A
314
Q

In potential divider diagrams, what is:
• Vs
• R1
• R2

A
  • Vs - Source voltage
  • R1 - Non-output resistor
  • R2 - Output resistor
315
Q

In a potential divider, if the source voltage is 9V and R1 is 100Ω, what must R2 be in order to get an output of 6V?

A

200Ω

316
Q

What is a simple potential divider used for?

A

Calibrating voltmeters, which have a high resistance.

317
Q

In a simple potential divider, what happens when you add a component with low resistance across R2 (the output resistor), what happens and why?

A
  • You now have two resistors in parallel, so the total resistance will be lower than R2.
  • This means that R2 will be lower than calculated.
318
Q

In a simple potential divider, what is the effect of replacing R1 (non-output resistor) with a variable resistor?

A

It allows the output voltage across R2 to be varied.

319
Q

In a simple potential divider with a variable resistor as R1, how does output voltage across R2 vary as the resistance R1 is increased?

A
  • When R1 = 0, V(out) = Vs

* As you increase R1, V(out) gets smaller

320
Q

How does the resistance of a light-dependent resistor vary?

A

Resistance decreases as light intensity increases:

LDR has very high resistance in the dark, lower resistance in the light.

321
Q

What is the circuit symbol for an LDR?

A
  • Circle with a rectangle inside it.
  • Wires reach to the rectangle, but not through it.
  • Arrows point to the circle.
322
Q

How does the resistance of a NTC thermistor vary?

A

Resistance decreases as temperature increases.

opposite to normal resistor, but much more

323
Q

How can a potential divider output be varied according to temperature or light intensity?

A

Using a thermistor or LDR as one of the resistors in the potential divider.

324
Q

When an LDR is connected as R1 in a potential divider, with the output across another resistor, R2, how will the output vary as light increasing increases and why?

A
  • Light gives the LDR a lower resistance.
  • So it uses less of the PD and more can go to the output.
  • Output voltage (V-out) increases as light intensity increases.
325
Q

What happens to V-out when temperature increases (R1 = thermistor)

A
326
Q

Give a use of LDRs and thermistors.

A

They can be included in circuits that control switches, e.g. to turn on a light or heating system.

327
Q

What is a potentiometer?

A

A type of potential divider that uses a single variable resistor instead of two fixed resistors to give a desired voltage output.

328
Q

How does a potentiometer divider work?

A
  • The slider can be moved along the variable resistor to change R1 and R2 as desired.
  • So V(out) can be varied from 0 to the source voltage
329
Q

When is a potentiometer useful?

A
  • When you need to change the voltage continuously

* e.g. The volume control of a stereo

A Level Physics (13 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2024 Bold Learning Solutions. Terms and Conditions