SDM Flashcards

1
Q

Which SDM command maximize routing on the switch?

A. sdm prefer routing
B. sdm prefer route-enabled
C. sdm prefer route-on
D. sdm prefer access-route

A

Answer: A

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Which two statements about GLBP are true? (Choose two)

A. Member devices send hello messages to multicast address 224.0.0.39.
B. Member devices must elect exactly one AVG.
C. Member device can elect one more AVGs.
D. The AVG assigns virtual MAC addresses to all group members.
E. It supports up to 32 groups on a single interface.

A

Answer: B D

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Which three features can be optimized by using SDM templates? (Choose three)

A. access
B. Port Security
C. VLAN
D. DHCP snooping
E. routing
F. Trunk
A

Answer: A C E

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Which statement about the use of SDM templates in a Cisco switch is true?

A. SDM templates are used to configure system resources in the switch to optimize support for specific features, depending on how the switch is used in the network.
B. SDM templates are used to create Layer 3 interfaces (switch virtual interfaces) to permit hosts in one VLAN to communicate with hosts in another VLAN.
C. SDM templates are used to configure ACLs that protect networks and specific hosts from unnecessary or unwanted traffic.
D. SDM templates are used to configure a set of ACLs that allows the users to manage the flow of traffic handled by the route processor.
E. SDM templates are configured by accessing the switch using the web interface.

A

Answer: A

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Which SDM template disables routing and supports the maximum number of unicast MAC addresses?

A. VLAN
B. access
C. default
D. routing

A

Answer: A

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Which SDM template is the most appropriate for a Layer 2 switch that provides connectivity to a large number of clients?

A. VLAN
B. default
C. access
D. routing

A

Answer: A

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

A network engineer deployed a switch that operates the LAN base feature set and decides to use the SDM VLAN template. The SDM template is causing the CPU of the switch to spike during peak working hours. What is the root cause of this issue?

A. The VLAN receives additional frames from neighboring switches.
B. The SDM VLAN template causes the MAC address-table to overflow.
C. The VLAN template disables routing in hardware.
D. The switch needs to be rebooted before the SDM template takes effect.

A

Answer: C

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Which two statements about SDM templates are true? (Choose two)

A. They are used to allocate system resources
B. Changing the SDM template will not disturb switch operation.
C. You can verify the SDM template that is in use with the show sdm prefer command
D. SDM templates are defined by the switch model and cannot be changed
E. SDM templates changes do not require switch to be rebooted

A

Answer: A C

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

In a switch stack where is the the SDM template stored?

A. All switches in stack
B. Master switch
C. Flash memory

A

Answer: B

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What types of SDM templates you can use in switch? (Choose four)

A. Access
B. Default
C. Routing
D. VLANs
E. ?
F. ?
A

Answer: A B C D

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Which three features can be optimized by using SDM templates? (Choose three)

A. port security
B. trunk
C. VLAN
D. access
E. DHCP snooping
F. routing
A

Answer: C D F

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

When SDM templates are configured, which action must be performed for the configuration to take effect?

A. reload
B. shutdown
C. write memory
D. backup config

A

Answer: A

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Which statement about the default Switch Database Management Template is true?

A. Template disables routing and supports the maximum number of unicast MAC addresses
B. Template maximizes system resources for access control lists
C. Template maximizes system resources for unicast routing
D. Template gives balance to all functions

A

Answer: D

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

A question about a Layer 2 switch has been moved over to a Layer 2 and Layer 3 environment but high CPU spike during work hours.

A. show sdm prefer vlan 
(config)# sdm prefer vlan
B. show sdm prefer routing 
(config)# sdm prefer routing
C. show sdm prefer
(config)# sdm prefer routing
D. show sdm prefer
(config)# sdm prefer default
A

Answer: D

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Which statement about the default Switch Database Management template is true?

A. The default template disables routing and supports the maximum number of unicast MAC addresses.
B. The default template gives balance to all functions.
C. The default template maximizes system resources for unicast routing.
D. The default template maximizes system resources for access control lists.

A

Answer: B

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Which SDM command will provide maximum usage for IPv4 and IPv6 routing, including IPv4 policy-based routing on a switch?

A. sdm prefer dual-ipv4-and-ipv6 routing
B. sdm prefer dual-ipv4-and-ipv6 default
C. sdm prefer dual-ipv4-and-ipv6 vlan
D. sdm prefer dual-ipv4-and-ipv6 access

A

Answer: A

17
Q

Which SDM command maximize routing on the switch?

A. sdm prefer routing
B. sdm prefer route-enabled
C. sdm prefer route-on
D. sdm prefer access-route

A

Answer: A