CDP & LLDP Flashcards
What is the default interval at which Cisco devices send Cisco Discovery Protocol advertisements?
A. 30 seconds
B. 60 seconds
C. 120 seconds
D. 300 seconds
Answer: B
Which statement about Cisco Discovery Protocol configuration on a Cisco switch is true?
A. CDP is enabled by default and can be disabled globally with the command
no cdp run.
B. CDP is disabled by default and can be enabled globally with the command
cdp enable.
C. CDP is enabled by default and can be disabled globally with the command
no cdp enable.
D. CDP is disabled by default and can be enabled globally with the command
cdp run.
Answer: A
A network engineer notices inconsistent Cisco Discovery Protocol neighbors according to the diagram that is provided. The engineer notices only a single neighbor that uses Cisco Discovery Protocol, but it has several routing neighbor relationships. What would cause the output to show only the single neighbor?
A. The routers are connected via a Layer 2 switch.
B. IP routing is disabled on neighboring devices.
C. Cisco Express Forwarding is enabled locally.
D. Cisco Discovery Protocol advertisements are inconsistent between the local and remote devices.
Answer: A
After the implementation of several different types of switches from different vendors, a network engineer notices that directly connected devices that use Cisco Discovery Protocol are not visible. Which vendor-neutral protocol could be used to resolve this issue?
A. Local Area Mobility
B. Link Layer Discovery Protocol
C. NetFlow
D. Directed Response Protocol
Answer: B
While doing network discovery using Cisco Discovery Protocol, it is found that rapid error tracking is not currently enabled. Which option must be enabled to allow for enhanced reporting mechanisms using Cisco Discovery Protocol?
A. Cisco Discovery Protocol version 2
B. Cisco IOS Embedded Event Manager
C. logging buffered
D. Cisco Discovery Protocol source interface
E. Cisco Discovery Protocol logging options
Answer: A
A network engineer has just deployed a non-Cisco device in the network and wants to get information about it from a connected device. Cisco Discovery Protocol is not supported, so the open standard protocol must be configured. Which protocol does the network engineer configure on both devices to accomplish this?
A. IRDP
B. LLDP
C. NDP
D. LLTD
Answer: B
Which statement about Cisco devices learning about each other through Cisco Discovery Protocol is true?
A. Each device sends periodic advertisements to multicast address 01:00:0C:CC:CC:CC.
B. Each device broadcasts periodic advertisements to all of its neighbors.
C. Each device sends periodic advertisements to a central device that builds the network topology.
D. Each device sends periodic advertisements to all IP addresses in its ARP table.
Answer: A
Which option lists the information that is contained in a Cisco Discovery Protocol advertisement?
A. native VLAN IDs, port-duplex, hardware platform
B. native VLAN IDs, port-duplex, memory errors
C. native VLAN IDs, memory errors, hardware platform
D. port-duplex, hardware platform, memory errors
Answer: A
Which statement about LLDP-MED is true?
A. LLDP-MED is an extension to LLDP that operates between endpoint devices and network devices.
B. LLDP-MED is an extension to LLDP that operates only between network devices.
C. LLDP-MED is an extension to LLDP that operates only between endpoint devices.
D. LLDP-MED is an extension to LLDP that operates between routers that run BGP.
Answer: A
Which option describes a limitation of LLDP?
A. LLDP cannot provide information about VTP.
B. LLDP does not support TLVs.
C. LLDP can discover only Windows servers.
D. LLDP can discover up to two devices per port.
Answer: A
Which statement about using native VLANs to carry untagged frames is true?
A. Cisco Discovery Protocol version 2 carries native VLAN information, but version 1 does not.
B. Cisco Discovery Protocol version 1 carries native VLAN information, but version 2 does not.
C. Cisco Discovery Protocol version 1 and version 2 carry native VLAN information.
D. Cisco Discovery Protocol version 3 carries native VLAN information, but versions 1 and 2 do not.
Answer: A