Brainscape's Knowledge GenomeTM

Browse over 1 million classes created by top students, professors, publishers, and experts.


See full index

Gas Level 3 HBA > Safety and Regulations Test > Flashcards

Safety and Regulations Test Flashcards

1
Q

What best describes a key list of sefety categories to be considers by a Gas Technician

A

Personal, Tools, Equipment, Others, Site, OSHA, and the Ontario Gas Utilization Code.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

How would a gas technician demonstate concern for the safety for others?

A

Demonstating the correct use of a new tool to a co-worker.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What should a gas technician do when a new piece of equipment is introduced for use?

A

Get a copy of the users manual and read it before using the equipment.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What does OSHA stand for?

A

Occupational Health & Safety Acts

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Whom regulates workplace safety, in Ontario?

A

The Province of Ontario

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

What should MSDS sheets be used for by a Technician?

A

To be aware of Flammable, Corrosive, or Explosive Substances.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

What does MSDS stand for?

A

Material Safety Data Sheet

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

When can you ignore a hazard?

A

Never, The Hazard is the responsibility of the person who is aware of it.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

When lifting a heavy object, how should you lift?

A

When lifting, it is best to lift by bending you knees and using your leg muscles.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Why should garbage and debris be removed from a job site?

A

To prevent slips,trips and falls.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

An employer is responsible for..?

A

Ensuring that safety instruction is provided to workers.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

True or False;
Workers have a right to refuse to wear safety clothing that an employer instructs them to wear.

A

False, Workers must follow safety protocols, and wear safety clothing that the employers instructs them to wear.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

The Workers Compensation Board Act, says that in all cases of injury or disease an EMPLOYER must?

A

Make sure there is a record of the first aid treatment/ or any advice given to the worker.

When you get an injury, you have to report it to your supervisor.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

According to the Workers Compensation Board Act, what is the workers obligation in all cases of injury/disease?

A

Notify the employer within eight hours.

Obviously seek medical attention first.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What are the classes of fire extinguisher, and how many are their?

A

5 Classes
A,B,C,D,K

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

What is a class A fire extinguisher used for?

A

Ordinary Combustibles

Wood,Paper,Cloth,ETC.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

What is a class B fire extinguisher used for?

A

Flammable Liquids

Grease, Oil, Paint, Solvent, Gasoline.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

What is a Class C fire extinguisher used for?

A

LIVE electrical equipment

Electrical Panel, Motor, A/C, Furnace, Wiring, ETC

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

What is a class D fire extinguisher used for?

A

Combustible Metals
Reactive Metals

Magnesium, Aluminum,ETC.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

What is Class K fire extinguisher used for?

A

Commercial Cooking Equipment

Cooking Oils, Animal Fats,Vegetable Oils

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

What are the KEY pieces of PPE for a technician.

A

Hard hat, gloves, ear plugs, dust mask, safety glasses, work boots, face shields

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

Shot for powder activated guns is stored?

Ramset blank shot for example.

A

In a dry, secure location.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

How should an electric drill be disconnected?

A

By pulling the plug at the outlet.

Pulling on the cord could damage the connection, causing a shock.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
Q

How often should a fire extinguisher be inspected?

A

Once a year

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
25
Q

Which organization is responsible for administering fuel regulations for the installation of gas and oil appliances in Ontario?

A

TSSA

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
26
Q

What does TSSA stand for?

A

Technical Standards and Safety Authority

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
27
Q

Which Organizations are able to certify gas appliances, equipment and accessories in Ontario?

A

Canadian Gas Association,
Underwriters Laboratories of Canada,
The Canadian Standards Association,
And the Technical Standards and Safety Authority.

28
Q

Who is the Ultimate Authority Under the TSSA as it applies to the installation of Gas and propane appliances and equipment?

A

The Ontario Government.

29
Q

Propane cylinders used in Ontario must be Manufactured and approved to the requirements established by?

A

Transport Canada

30
Q

Requalification of refillable propane cylinders used in Ontario must be done in accordance with the procedures for cylinders as established by?

A

Compressed Gas Association

31
Q

Which Organization registers certified Gas and Oil technicians in Ontario?

A

TSSA

32
Q

A steam boiler shall conform to the requirements of which agency or organization?

A

TSSA

33
Q

Propane cylinders manufactured after 1993 are to be built and marked to the specification of?

A

Transport Canada

34
Q

What does the B149.1 Installation code cover?

A

Installation of Appliances,
Installation of Venting,
Installation of Gas Piping,
Code Regulations

35
Q

A G1 Technician can work on?

A

An appliance with any input in a vapour phase

36
Q

A G2 Technician can work on?

A

An apllaince with inputs up to 400,000 BTU’s

37
Q

A G3 Technician is allowed to?

A

Reactivate existing installations of appliances up too 400,000 BTUhs

38
Q

What actions shall a person holding a gas Technician certification take if an installation does not meet code, but doesnt present an immidiate danger?

A

The person shall notify the distributor and the owner in writing of the condition.

B tag- On Appliance, In Customer hands, and sent to Distributor.

39
Q

What code expression is used to describe a structure used in connection with dirct trade or service to the public?

A

Commercial Building

40
Q

Which code expression describes a building used in connection with production or process work or with storage or warehousing?

A

Industrial Building

41
Q

Which code expression describes a building used by a gathering of persons for civic, political, travel, religious, social, educational, recreational, or like purposes or for the consumption of food and drink?

A

What is, an Assembly building

42
Q

What is the expression for a housekeeping unit, used or intended to be used as a domicile by one or more persons and usually contain cooking, living, sleeping, and sanitary facillities?

A

Dwelling unit

43
Q

When is a certification required in order to install or service a propane appliance?

A

When installing or servicing an appliance in other than ones own residence.

44
Q

Where an appliance cannot be installed in accordance with regulation, what is required to be done?

A

Prior to installation, a deviation from the regulations must be applied for and accepted by the TSSA

45
Q

To determine the specific purpose of an appliances use, you should?

A

Consult the instruction manual

46
Q

When referring to the appliance Manufacturer’s instruction manual, code requires?

A

It be left with the end user.

47
Q

When the installation of an appliance consitutes a conversion from another form of energy to gas, the installer must?

A

Advise the user in writing of the procedures to be followed in discontinuing the supply of the former form of energy.

48
Q

Where the heat exchanger of an appliance in a dwelling is found to be defective you must?

A

Replace the Heat exchanger.

49
Q

When an appliance is installed on a roof, the minimum clearance between the appliance and the edge shall be?

A

6 feet

50
Q

Instructin the user in the safe and correct operation of a newly installed appliance is the responsibility of?

A

The appliance installer

51
Q

Where premises are connected to a gas supply for the first time no person shall initialize an appliance until?

A

The fuel distributor has examined and accepted the installation.

52
Q

What establishes the minimum standards for the repair and servicing of gas appliances?

A

Natural gas and propane installation code.

The B149.1 Code book

53
Q

In a situation that constitutes an immediate hazard, a gas technician shall?

A

Shut off Gas supply and inform the gas distributor of the situation immediate.

‘A’ Tag it, shut off Gas, tag appliance, customer, and distributor.

54
Q

When handling asbestos on a boiler you must refer to…?

A

Occupational health and safety act and regulations

55
Q

Welded gas piping must comply with?

A

TSSA

56
Q

When manufacturing instructions do not state the required clearances between combustible material and the base of the factory built chimney the installer may refer to…?

A

Ontario Building Code

57
Q

When a new appliance is to be installed when work permits and inspections are required, whose responsibility is it secure the necessary permits and inspections?

A

The installer is responsible.

58
Q

The installation of a gas burning appliance in a MOBILE home shall be in accordance with?

A

CSA Standar Z240.4.1

59
Q

The installation of gas burning appliances in RECREATIONAL vehicles shall be in accordance with?

A

CSA Standard Z240.4.2

60
Q

When cylinders are being transprted, they shall be secured..?

A

In an upright postion, in a well ventilated location with a relief valve communicating with the vapour cspace only

61
Q

The Ontario Natural gas utilization code is used to determine..?

A

Regulations for installing gas appliances

62
Q

Equipment service bulletines are normally issued by the..?

A

Manufacturer

63
Q

Safety directives and bulletins are published by..?

A

TSSA

64
Q

Instructing the user in the safe and correct operation of a newly installed appliance is the responsiblity of the..?

A

Appliance installer

65
Q
A

Gas Level 3 HBA (4 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2024 Bold Learning Solutions. Terms and Conditions