Rigs Flashcards
1
Q
Becker Height
A
10’1”
2
Q
Becker Weight
A
42,000 lbs
3
Q
Becker Width
A
8’8”/9’8” with mirrors
4
Q
Becker Length
A
32’9”
5
Q
Becker Foam Tank Size
A
30 Gallons
6
Q
Becker Oil amount
A
38 qts
7
Q
Becker Transmission Fluid
A
47 qts
8
Q
Becker Fuel
A
50 gallons diesel
9
Q
Becker Turning Radius
A
71’10”
10
Q
Becker: What is the req’d air pressure for the low air pressure light and buzzer to turn off?
A
60psi front and rear
11
Q
Becker: Crank Engine ____ sec. then wait ____sec. to attempt again.
A
15 seconds; 60 seconds
12
Q
Becker: How many speeds?
A
5 Forward and 1 Reverse
13
Q
Becker: How do you attain 5th gear?
A
Mode button
14
Q
Becker: What lights turn off when rig is parked?
A
White flashing lights
15
Q
Becker: Load Manage Sequence ___ to ___.
A
1 to 8
16
Q
Becker: After ___ minutes, electrical loads will shed.
A
1 minute
17
Q
Becker: Loads will remain off for ____ min and until unshed voltage is achieved for ___ min.
A
5 minutes; 1 minute
18
Q
Becker: What has to be set for the loads to shed?
A
Parking Brake
19
Q
Becker: Don’t run the primer longer than ___sec. The pump should prime within ___ to ___ sec.
A
60 seconds; 15-45 seconds
20
Q
Becker: Where can you view the oil level for the primer pump?
A
Passenger Pump Panel
21
Q
Becker: List the two modes of operation for the Electronic Fire Commander.
A
RPM and Pressure
22
Q
Becker: How do you enter the programming menu?
A
Hold ‘mode’ and ‘menu’ simultaneously.
23
Q
Becker: _____ exits and saves changes. ____ exits without saving changes.
A
Idle; Mode
24
Q
Becker: RPM increase and decrease in ____ increments. Whereas Pressure mode increases and decreases in ____ increments.
A
25 RPM; 4 psi
25
E1 Cyclone: Height
9'
26
E1 Cyclone: Weight
38,600 lbs
27
E1 Cyclone: Width
8'
28
E1 Cyclone: Length
30'6"
29
E1 Cyclone: Oil Capacity
32 qts of 30W
30
E1 Cyclone: Trans Fluid Capacity
33qts of Dex
31
E1 Cyclone: Fuel Consumption
5-6 gallons per hour
32
E1 Cyclone: Primer Oil
4 qts of 30W
33
E1 Cyclone: Power Steering Fluid
10W40
34
E1 Cyclone:Hose
```
1100' of 4"
300' of 1 3/4"
200' of 2"
200' of 1"
Additional 200' of 2 1/2" (not preconnected)
```
35
E1 Cyclone:What is adequate oil pressure?
40-60 psi (5-10psi @ idle)
36
E1 Cyclone: What is the normal air pressure to operate the parking brake?
90-120psi
37
E1 Cyclone:What is the normal operating temperature?
160-210 F
38
E1 Cyclone:Crank ___ sec, wait ___ sec., attempt to start ____ times.
15-20 sec; 30 sec; 3-4 times
39
E1 Cyclone: Idle engine ___ minutes after stopping.
3-5 minutes
40
E1 Cyclone: Telma Retarder has ___ stages and supplies up to ___% of stopping force?
4; 85%
41
E1 Cyclone: What does the speedometer show in pump gear?
25-35 mph
42
E1 Cyclone: How many large discharges?
5, and #5 is a 3" with stortz
43
E1 Cyclone: The gated relief on the intake is set @ ____.
150 or 250 psi
44
E1 Cyclone: There are ____ preconnects.
Front- 100-150' 1 3/4"
Right- 150-200' 2"
Rear- 200' 1 3/4"
45
E1 Cyclone: Where is the manual pump shift located?
There is no manual pump shift on the E1 Cyclone.
46
E1 Cyclone: What do you pump with foam operations?
200 psi
47
E1 Cyclone: What % foam mix?
1%, 2%, 3%, 6%
48
E1 Cyclone: Flush the foam from all discharges at ____ psi
100 psi
49
E1 Teleboom: Height
12'
50
E1 Teleboom: Weight
43,000 lbs
51
E1 Teleboom: Width
8'; 9'10" with stabilizers
52
E1 Teleboom: Length
32'
53
E1 Teleboom: Oil
32 qts of 30W
54
E1 Teleboom: Transmission Fluid
33 qts of Dextron II
55
E1 Teleboom: Primer Fluid
6 qts of 30W
56
E1 Teleboom: Power Steering Fluid
10W40
57
E1 Teleboom: Ladders
50' Tele
24' Ext
14' Roof
10' Attic
58
E1 Teleboom: Turning Radius
34'-37'
59
E1 Teleboom: Waterway Nozzle capability
300-1000 GPM
60
E1 Teleboom: Tire Pressures
Front 110; Rear 115
61
E1 Teleboom: Hose
1100' of 4"
300' of 1 3/4"
200' of 2"
200' of 1"
62
E1 Teleboom: What is the oil pressure after starting?
40-60psi
63
E1 Teleboom: Idle to increase air pressure to ____ to release the Parking Brake.
90-120 psi
64
E1 Teleboom: Normal Operating Temperature
160-210 F
65
E1 Teleboom: Crank for ___ sec, wait ___ sec, attempt ___ times.
15-20 sec; 30 sec.; 3-4 attempts
66
E1 Teleboom: Allow the engine to idle ___ minutes before stopping.
3-5 minutes
67
E1 Teleboom: Telma is in ___ position before brake is applied.
Position 3
68
E1 Teleboom: What keeps the pump throttle from working?
Park Brake not engaged
69
E1 Teleboom: Wait ___ sec to shift the pump shift from neutral to pump.
2-3 seconds.
70
E1 Teleboom: Speedometer will show ___mph in pump gear.
25-35 mph
71
E1 Teleboom: Don't engage the PTO when ____.
The water pump is in operation
72
E1 Teleboom: List two reasons for no throttle in the cab.
1. Pump is in gear.
| 2. Check Eng Light is pushed in.
73
E1 Teleboom: List three reasons there is no throttle at the pump panel.
1. Pump not engaged.
2. Check Eng Light is pushed in.
3. Park Brake not engaged.
74
E1 Teleboom: Fast idle at ___ RPM.
1200 RPM
75
E1 Teleboom: List three reasons for the fast idle not working.
1. No fast idle if park brake isn't set.
2. No fast idle if pump is engaged.
3. No fast idle if not in neutral.
76
E1 Teleboom: Pump ___psi for 1000gpm
180 psi
77
E1 Teleboom: Don't operate on grades greater than ___%.
6%
78
E1 Teleboom: The only controls on the officers pump panel are?
Intakes and Drains
79
E1 Teleboom: Where are Tele-Boom controls located?
Rear Panel
80
E1 Teleboom: When using the Foam System, when must you reset the metering valve?
Each time the GPM is changed.
81
E1 Teleboom: Foam System suction pressure mustn't exceed ___psi
10 psi
82
E1 Teleboom: Foam System engine pressure ___ to ___ psi?
125-250psi
83
E1 Teleboom: Pressing the check engine light does what?
1. Disengages the foot throttle
| 2. Lights up a flash code
84
E1 Teleboom: What does two then five flashes mean from the check engine light upon testing?
Everything is good.
85
E1 Teleboom: What insulates the Boom/Ladder Assembly?
It is not insulated.
86
E1 Teleboom: What is the air pressure req'd for PTO engagement?
70-140 psi
87
E1 Teleboom: No Boom operations with winds greater than ___mph?
35mph
88
E1 Teleboom: Where is the temperature indicator located on the Boom?
At the tip.
89
E1 Teleboom: What does ice build up do?
Decrease the load and extension capabilities.
90
E1 Teleboom: What drives the auxiliary motor?
12V DC electric motor of of the vehicle batteries.
91
HME 55' Teleboom: Height
11'7"
92
HME 55' Teleboom: Weight
45,000 lbs
93
HME 55' Teleboom: Width
9'6" / 13" with stabilizers
94
HME 55' Teleboom: Length
31'2"
95
HME 55' Teleboom: Oil Capacity
41qts of 15W40
96
HME 55' Teleboom: Transmission Fluid
51qts of Dex II
97
HME 55' Teleboom: Primer Fluid
1 gallon of 30W
98
HME 55' Teleboom: Coolant
39qts of 50/50
99
HME 55' Teleboom: Turning Radius
Left 69'3"
| Right 65'3"
100
HME 55' Teleboom: Tire Pressure
120 psi cold
101
HME 55' Teleboom: Approach/Departure Angles.
12 deg/ 13 deg
102
HME 55' Teleboom: Clearance
9"
103
HME 55' Teleboom: Vertical Reach
55' 5 1/4"
104
HME 55' Teleboom: Horizontal Reach
46'8"
105
HME 55' Teleboom: Flow Capacity
250-1000 GPM
106
HME 55' Teleboom: What gear is used for PTO
Neutral
107
HME 55' Teleboom: How high do you fill the hydraulic fluid reservoir?
Within 2" of lower edge.
108
HME 55' Teleboom: Crank ___ sec, wait ___ sec, repeat ___ times.
15-20 sec, 30 sec, 3-4 attempts
109
HME 55' Teleboom: What is adequate oil pressure?
40-60 psi
110
HME 55' Teleboom: What is adequate air pressure to release parking brake?
90-120psi
111
HME 55' Teleboom: What is the normal operating temperature?
180-190 deg F
112
HME 55' Teleboom: What inhibits shifting (N) to (D)?
If high idle switch is activated.
113
HME 55' Teleboom: What do you do if there is no positive pressure at the pump panel?
Run the primer motor
114
HME 55' Teleboom: How long can you run the primer motor?
60 sec.
115
HME 55' Teleboom: What is the relief valve set at on the drivers side angus valve ___psi; and on the rear operated wheel intake ___psi
200psi; 250psi
116
HME 55' Teleboom: Where is the cab tilt control located?
Right Pump Panel
117
HME 55' Teleboom: What socket size for the manual front intake control?
25/32" socket
118
HME 55' Teleboom: After shifting to neutral, how long must you wait to disengage the pump?
5 seconds
119
HME 55' Teleboom: Where are the aerial controls located?
Upper Right Drivers Pump Panel
| Rear Panel Below Turntable
120
HME 55' Teleboom: The auxiliary pump switch can be ran ___ sec. and then rest ___sec.
30 sec; 60 sec.
121
HME 55' Teleboom: Slow to ___ mph to engage insta-chains.
less than 25mph
122
HME 55' Teleboom: Engage insta-chains between what speeds?
5-25 mph
123
HME 55' Teleboom: Insta chains shouldn't exceed ___mph.
30mph
124
HME 55' Teleboom: Insta-chains in reverse work best at what speeds?
Above 7-10mph
125
HME 55' Teleboom: Insta-chains are not effective when depths exceed ___"
6-8"
126
HME 55' Teleboom: What is req'd before power is sent to rear control panel?
Chassis spring brakes set
| Transmission in N or D.
127
HME 55' Teleboom: What type and how many stabilizers.
Two telescopic tubular welded steel stabilizers
128
HME 55' Teleboom: How many ladder sections with what size handrails?
Two sections with 1" handrails
129
HME 55' Teleboom: Boom Nozzle Range of Elevation ____; Side Sweep ____; and Flow capacity ____, auto adjusts to ___psi
135 deg
180 deg
250-1000 GPM
85-100 psi
130
HME 55' Teleboom: What is the reactive force at 1000GPM with 80psi?
495lbs
131
HME 55' Teleboom: If parked on a slope, spot so work is done on which side?
High side
132
HME 55' Teleboom: Power shift PTO's req less than ___ RPM to engage.
1000RPM
133
HME 55' Teleboom: Raise stabilizers until rear step elevates ___ inches
3-4 inches
134
HME 55' Teleboom: Stabilize which side first?
Downhill
135
HME 55' Teleboom: Open rear butterfly valve to ___ psi, never exceed ___psi, increase speed with throttle at pump panel to ___ psi
120psi
200psi
150psi range
136
HME 55' Teleboom: Pressure at the nozzle varies ___psi between positions
38psi
137
Simon LTI QS-82: Height
11'6"
138
Simon LTI QS-82: Weight
60,000 lbs
139
Simon LTI QS-82: Width
10' / 16' with stabilizers
140
Simon LTI QS-82: Length
37'10"
141
Simon LTI QS-82: Water tank size/material
Polypropylene 150 gallon
142
Simon LTI QS-82: Top Speed
65mph
143
Simon LTI QS-82: Self Lubing system, how many points and how often?
28 pts every 6 hrs
144
Simon LTI QS-82: Turning Radius
35'6"
145
Simon LTI QS-82: Angle of Approach/Departure
12 deg / 11 deg
146
Simon LTI QS-82: Ladder capacity
500 lbs
147
Simon LTI QS-82: Turntable size and rotation
96" X 96" ; 34"
148
Simon LTI QS-82: Pre-piped Waterway ___GPM
1000GPM
149
Simon LTI QS-82: Hose
200' of 1"
150
Simon LTI QS-82: Electric Cable Reels
2 X 250'
151
Simon LTI QS-82: What %/Deg allows full capacity?
Less than 6% or 3.5 deg.
152
Simon LTI QS-82: Capacity decreases by 1/2 at ___.
6-14% or 3.5-8 deg
153
Simon LTI QS-82: How do you compensate for ice/snow accumulation?
Decrease load capacity
154
Simon LTI QS-82: ____ cannot be performed with water tower operations; instead you must ___.
swing; rotate the monitor
155
Simon LTI QS-82: Fast idle at ___
1500-1600 RPM
156
Simon LTI QS-82: What size pressure gauge in outrigger valve bank?
0-5000 psi
157
Simon LTI QS-82: How do you engage the circuit selector
1/4 turn Left or Right
158
Simon LTI QS-82: What type of aerial elevation indicator? Calibrated at ___?
Floating Ball Type; -20 deg to 80 deg
159
Simon LTI QS-82: What activates the rotation limiting system?
There is no rotation limiting system
160
Simon LTI QS-82: What position is the most stable operating position for the ladder?
Over the rear; 45 deg angle to each side
161
Simon LTI QS-82: slow idle
600 RPM
162
Simon LTI QS-82: Leave ___ clearance above locking pins?
1/4"
163
Simon LTI QS-82: Where do you pin the monitor for rescue? what about for water tower operations?
mid-section; fly-section
164
Simon LTI QS-82: In sub-zero temps, operate the pump at slow idle (600 RPM) until hydraulic oil reaches ___.
60 deg F.
165
Simon LTI QS-82: EPU should be ran how often?
Every ten hours of ladder use.
166
Simon LTI QS-82: Grease the ladder with ?
Amsoil and 3" brush
167
Ford LTS 9000: Height
9'6"
168
Ford LTS 9000: Weight
50,000 lbs
169
Ford LTS 9000: Width
9'2"
170
Ford LTS 9000: Length
33'8"
171
Ford LTS 9000: Tank Capacity
2,500 gallons
172
Ford LTS 9000: Floor to running board height
24"
173
Ford LTS 9000: Turning Radius
44'
174
Ford LTS 9000: Tire Pressures
Front- 120
| Rear- 95-105
175
Ford LTS 9000: Fuel Capacity of Engine, Wisconsin, High Pressure?
50 gal, 40 gal, 2 gal
176
Ford LTS 9000: Transmission Fluid
36 pints Dex II
177
Ford LTS 9000: Oil Capacity
36 qts of 15W40
178
Ford LTS 9000: Primer Fluid
4 qts SAE 30
179
Ford LTS 9000: Power Steering Fluid
Merson
180
Ford LTS 9000: Auxiliary pump oil capacity
3.18 qts 10W40
181
Ford LTS 9000: Max Speed in locked position
35 mph
182
Ford LTS 9000: Oil Pressure
20-80psi
183
Ford LTS 9000: Water Temperature
190-195 deg F
184
Ford LTS 9000: In 'D', the transmission operates what gears?
2-5
185
Ford LTS 9000: Wisconsin pump engine shuts off at ___
190 deg F
186
Ford LTS 9000: If both levers are set at 90 deg, the turrett will sweep ___.
180 deg.
187
Ford LTS 9000: Wisconsin pump controls are outlined in ___; while the high pressure controls are outlined in ___.
Black; Red
188
Ford LTS 9000: Where is the choke lever located outside the cab?
There is no choke lever outside the cab.
189
Ford LTS 9000: Throttle the Wisconsin pump to ___ to prime.
1300-1500 RPM
190
Ford LTS 9000: Drafting; The max pump capacity fall off above ___ ft.
10'
191
Ford LTS 9000: Submerge the strainer ___ x the pipe diameter.
4 X
192
Ford LTS 9000: Drafting; If shut down for a short period of time, slow down to ___#
50#
193
Ford LTS 9000: When dumping supply, you can dump ____ gallons in 50 sec and the remainder takes ____ minutes.
2,000 gallons; four minutes
