Red River IP Flashcards
1
Q
When using a Hacksaw, how many teeth should be in contact with the material?
A
3
2
Q
What is the procedure for changing the blade on a table saw?
A
Turn off main power
Remove throat plate
loosen nut toward you.
3
Q
When regluing a joint on a pre - 1940 piece of furniture, what kind of glue should be used
A
Hide Glue
4
Q
When setting up a dado set for a rabbet cut what is the procedure order
A
set fence raise blade into auxiliary fence
5
Q
Method used to install pre finished wall paneling
A
French Cleats
6
Q
What is the most conspicuous joint to use when installing wall panels
A
V-Groove
7
Q
When assembling an apron to a leg in furniture construction, what is the preferred method
A
Mortise & Tenon
8
Q
How would you fix or replace the rail on a chair?
A
Cut a scarf in the middle and remove
9
Q
How do you make a taper jig for the shaper
A
MDF and toggle clamps
10
Q
On a butlers table, what configuration is the hinge
A
Hinge with Pin down
11
Q
Quickest way to fasten a face frame?
A
Pocket Screws
12
Q
When attaching a solid surface edge what type of glue do you use?
A
Epoxy
13
Q
What kind of glue should be used for exterior laminations?
A
Resorcinol
14
Q
What method is used to fasten cabinets squarely in production
A
Dowels PVA glue and Case Clamps
15
Q
On a portable belt sander, what is the backing of the sandpaper made from?
A
Resin bond cloth back
16
Q
When truing up two edges on a laminated curve molding, what procedure is used?
A
joint one edge then rip on table saw
17
Q
Smallest piece of stock you should cut on table saw
A
10 x 6 x 300
18
Q
Sequence of operation of the tenon machine?
A
Score shoulder
Tenon
Cope
Cutoff
19
Q
When cutting out a sink hole in a p-lam top, what would you use?
A
Jigsaw downward blade using downward pressure
20
Q
What can be used to remove the latex contact cement off a counter top
A
Water
21
Q
What would be the best joint to use to attach the legs to a pedestal
A
Dovetail
22
Q
When using powder-actuated fasteners, how do you test the base material?
A
Use the fastener as a center punch and hit with hammer
23
Q
When gluing a solid surface table edge to a solid surface top, what must be done before gluing?
A
Wipe with methyl hydrate
24
Q
What kind of cut is used to produce birds eye maple
A
Rotary
25
When installing a warped door on a cabinet, the doors should be installed with the?
Crown out
26
When screwing two cabinets together with 3/4 inch gables together, what should you drill
1" deep hole with a #8 screw
27
How do you attach solid surface end to end?
Butt with epoxy
28
How do you assemble a French door
Frame with Muntins
Glass
Stops
29
How do you assemble a solid plinth to a hutch?
Web frame and screw
30
What is the advantage of a high vol low pressure spray gun (HPLV)
Cheaper
31
When picking P-Lam what should you choose?
GP on horizontal
V32 on vertical
32
How do you protect a cabinet base?
Staple skids
33
Procedure for stripping an antique chair?
Test old finish with appropriate stripper
34
When we make a hole in wood we are
Boring a Hole
35
How do you apply an oil based stain
Apply with brush or pad
Let soak
Wipe off excess
36
How do you apply a water based stain?
Sponge with water
Sand
Apply Stain
37
When using the saw attachment feature on a CNC, how do you reduce chipping?
Decrease Feed Rate
38
When running multiple parts on a CNC, What fields would be the best and fastest use the photo below
A & D
39
When attaching a solid surface to a cabinet, what method is used?
Silicone and Brace
40
After stripping furniture, what should you use to neutralize the stripper
Methyl Hydrate
41
What safety precautions do you use when stripping furniture with a toxic stripper
Goggles, Respi, Rubber gloves
42
Difference between mixing pre-catalyzed lacquer and post-catalyzed lacquer after mixing
Post catalyzed is more resistant to water and has a harder finish
43
What system is used to base CAD systems on?
Cartesian coordinate system
44
How would you make a solid surface edge
1" Solid surface build up, epoxy adhesive and spring clamps
45
When you laminate solid, what do you do to your form?
Allow for spring back
46
When you steam bending, what do you do to your bending form?
Allow for spring back
47
How do you fix a bubble in Veneer
Needle with glue
48
How do you attach a solid surface edge to a normal particle core laminate
Solvent Contact Cement
49
What is done to a cabinet to prepare for delivery?
Check product quality and wrap
50
How do you assemble a counter top with a solid edge?
Biscuit and Glue
51
How do you cut laminate for a finished floor
1/2" oversize.
52
How do you assemble a circular stave column?
Biscuit and Band clamp
53
How do you install a decorative butt hinge
Router door then style
54
When laminating solid with PVA how long do you leave the glue?
30 min
24hrs to fully cure
55
How do you make a post-form countertop?
Contact
Heat
Press
56
How do you clamp a center divider?
Solid Blocks with a slight crown and clamp
57
Steps for a prototype?
Need, Quality, Cost
58
What is used on the bed of a table saw?
Dry Lube
58
Proper maintenance for an air compressor?
Drain fluid
Change filter
59
What do you do everyday to an air nailer?
Oil
60
What are the steps for making a dado on an overhead router
Set depth then fence
61
When do you install crown molding on a free standing unit?
Before Installation
62
What is used in the 32 mm system?
Dowels
Holes
63
What is done when laying up a solid top?
Clamps alternate on the top and bottom of glue up
64
How do you fix a board with a crook?
Table saw with board fixed to auxiliary board
65
How do you glue up blanks
Annual ring direction is alternated
66
When using French cleats to install wall paneling, how are they installed?
30 deg down on panel, 30 deg up on wall
67
How do you attach a leg and rail assembly to a veneer top?
Pocket screws
68
When light sanding what type of back is used on the sandpaper
A
69
What is the angle of the bit when drilling
118 degrees with high rpms
70
How do you make a bow front door
Veneer ply's, form and vacuum press
71
How would you fix this drawer slide that is not level and has bounce to it?
(Incomplete need to post picture)
Raise back right side
72
How do you connect arm rests to legs?
Dowel
73
How do you attach a leg and rail assembly to a solid top?
Angle Bracket
74
When attaching stretchers and rails to legs, what is assembled last?
Leg
75
What causes the stroke sander belt to cup?
To much tension on the belt
75
When making picture frames, how do you add a decorative spline
Table Saw and vertical 45 degree V Jig
76
Honing angle of a chisel?
30 - 35 degrees
77
What causes a snipe on a planer?
Pressure bar to high
78
What is the best drawing to show the location of cabinets?
Plan
79
What causes a snipe on the jointer?
Outfeed to Low
80
Where do the braces go on the ledged, braced and batten door shown below
C
81
How do you increase the speed of the chuck?
Increase size of driver pulley
82
Moisture would most affect which dimension?
Width
83
What part would be sanded last on a 5 piece raised panel door?
Style
84
What type of veneer match is shownl
Slip
85
What kind of abrasive do you use to sand hardwood?
Aluminum Oxide
86
What kind of stain dries the fastest?
NGR stains
87
What is the minimum radius that General Purpose HPDL can be bent to?
100mm
88
What wood has the worst bending quality
Pine
89
What tool is used to make grooves on the lathe
Parting tool
90
What is the best square for gauging?
Combination SQ
91
What is the best way to inlay a vein in a round top table
Veneer top
route out vein
Inlay solid
Trim
92
What type of cutter head for the shaper is the worst?
Clamp type cutter
93
Which way do you move a dovetail bit to tighten the joint?
Raise the bit
94
What is considered a finishing belt on a wide belt sander?
150 - 180 Grit
95
Collars are used on the shaper to control what?
Width of cut
96
Too much clamping pressure will cause what?
Starved joint
97
When using a wooden spline, the grain runs in which direction?
90 Degrees to the joint
98
What diagram shows what a perfectly sharpened chisel looks like?
A
99
Which plane iron has the bevel up?
Block Plane
100
Which part of the molder holds the piece down and reduces tearing of the grain?
Chip Breaker
101
What grit of sandpaper do you use before finishing?
180
102
What is the minimum distance from the edge of a table to the supporting column below it?
18"
103
How much clearance is required above a sink or stove?
30"
104
The wooden block that gets attached to the corner is called what?
Glue block
105
What is the strongest joint for end to end gluing?
Finger
106
When using charges for powder actuated fastening, what is the strongest charge?
Purple
107
What do riving knives do when cutting on a table saw?
Keep the Kerf open
108
What type of joint is being shown?
Stop Dado
109
What kind of joint is being shown
Stop dado no picture on test
110
What is the grinding angle of a plane iron?
25 - 30 Degrees
111
How is a planer size determined?
Length of the Knives
112
What causes hesitation on a planer
Pressure bar to low
113
What causes a taper on a jointer
Outfeed to high
114
What causes a washboard on the jointer?
Feed rate to fast
115
Which rake angle of handsaw teeth would give you a faster cut?
9
116
Which table saw blade would be used to crosscut or rip?
Combination Blade
117
When looking at the overhead router, which drawing is correct?
D
118
How do you get an edge on a hand scraper?
Burnisher
119
What can you use to flatten burl veneer?
Sizing compound
120
What kind of mallet would you use to attach a T Moulding?
Rubber
121
What kind of Glue would you use to glue wood to metal?
Epoxy
122
What type of veneer match is shown?
Random Match
123
When you want to see 3 equal spaces on a sliding door unit, what are the sizes of the doors?
2 doors are bigger than 1
124
When there is a discrepancy on a job, what document over rules?
Specifications
125
Before installing millwork, what site conditions must be stable.?
Temperature and humidity
126
What is the best way to layout veneer for a board room table?
C
127
Redish Orange is what kind of colour
Tertiary
128
Which grain is best for painting to avoid telegraphing
Edge Grain
129
Name of auto fed multiblade saw?
Gang Saw
130
What kind of hand sander is best for finishing?
Straight Line
131
What is the best drill bit to drill flat bottom holes?
Forsner
132
How do you determine the size of a drill press?
Throat depth X 2
133
When using a belt sander, what kind of sanding is done to level the surface?
Cross sanding
134
How do you determine the size of a belt sander
Width of belt
135
How do you determine the size of a portable power drill?
Largest bit it will accommodate
136
Pigment oil stains uses what as a binder?
Boiled linseed oil
137
What is the easiest finish to repair?
Scandinavian Oil
138
What kind of screws should be used with oak?
Brass
139
Stain should be removed with what?
Oxilalic acid
140
What are vanishes and lacquers?
Top coats
141
What type of sander is used for irregular curves?
Spindle sander
142
What is the best method for attaching veneers together in high production?
Tapeless splicer
143
When installing 2 pieces of crown molding to an inside corner, what type of joint is used on the second piece?
Cope
144
How do you align dowel holes from rails to legs?
Dowel point or centres
145
What kind of door requires grooves or tracks?
Tambour
146
Which of the following woods has open grain?
Brasswood
Maple
Birch
Walnut
Walnut
147
How is the surface of open grain wood leveled?
Filler
148
How are stains classified?
Solvents used to make trhem
149
First basic step in finishing wood
Sanding
150
What is an abrasive often used for polishing varnished surfaces?
Rotten Stone
151
Best grade for Hard Lumber
FAS
152
Which of the following statements concerning pigment oil stains is correct?
They are transparent
Dry quickly
Remain on the surface
They penetrate deeply into the wood
They remain on the surface
153
How long should you wait before wiping a pigment oil stain?
2 - 8 minutes
154
What is the procedure for making a tack rag
cheesecloth dipped in thinned varnish
155
Which of the following finishes dries the most rapidly
Varnish
Polyurethane
Colored Paint
Lacquer
Lacquer
156
How is lumber from most needle-leaved trees rated?
Non porous
157
A list of hardwood would NOT include which of the following?
Ash
Oak
Walnut
Hemlock
Hemlock
158
How do you color a filler
Adding a stain
159
Woods that have small cells are best filled with what?
Liquid Filler
160
Primary purpose of filling?
Level the surface
161
If the work has been carefully filled and sealed, how many coats will produce a good finish?
Two Coats
162
To stop the wood from absorbing the oil from the putty, when do you fill the nail holes and cracks in the wood?
Between the sealer and first coat
163
What consistency do you apply paste filler?
Texture of cream
164
The brush recomended for application of varnish is a regular tapered or wedge-shaped brush, how many inches wide?
3" - 4"
165
Only one of these woods require a filler which is it?
Birch
Alder
Redwood
Chestnut
Chestnut
166
A list of hardwood would not include which of the following
Ash
Oak
Walnut
Hemlock
Hemlock
167
Close grain hardwood does not require what?
Filling
168
What is sheen the result of?
Rubbing
169
What is the fastest and most common route by which chemicals can enter the body?
Inhalation
170
When spraying, how much should you overlap each stroke?
50%
171
Recommended distance between the surface and the spray gun?
6" - 8"
172
Pulling the spray trigger back only slightly on a non bleeder results in the release of what?
Air Only
173
What is the function of a "spreader adjusting valve"
Control size of spray pattern
174
Orange peel is a finish defect cause by the material having?
To low of atomizinge air pressure on the spray gun
175
Which type of air and fluid mixture is recommended for fast drying materials?
External
176
What is the pebbly condition which occurs if very dry atomized particles fail to level properly and land on the surface?
Overspray
177
Which part of the spray gun is used to control the amount of paint that is released into the spray?
Fluid tip
