Premium

Question 1

What is an advantage of implementing inter-VLAN routing on an MX Security Appliance rather than performing inter-VLAN routing on an MS Series Switch?

A.
The MX appliance performs IDS/IPS for inter-VLAN traffic.
B.
The MX appliance performs data encryption for inter-VLAN traffic.
C.
The MX appliance performs content filtering for inter-VLAN traffic.
D.
The MX appliance performs AMP for inter-VLAN traffic.

Answer 1

Correct Answer: B

Question 2

What are two ways peers interact with ports that Auto VPN uses? (Choose two.)

A.
Peers contact the VPN registry at TCP port 9350.
B.
For IPsec tunneling, peers use UDP ports 500 and 4500.
C.
Peers contact the VPN registry at UDP port 9350.
D.
For IPsec tunneling, peers use high TCP ports within the 32768 to 61000 range.
E.
For IPsec tunneling, peers use high UDP ports within the 32768 to 61000 range.

Answer 2

Correct Answer: C,D

Question 3

A packet arrives on the VPN concentrator with source IP 10.168.70.3 and destined for IP 10.116.32.4.
What is the next hop for the packet, based on this concentrator routing table?

A.
The concentrator gateway (10.128.124.62) is the next hop.
B.
The Auto VPN peer "Store 1532 - appliance" is the next hop.
C.
The packet is stopped.
D.
Not enough detail is available to determine the next hop.

Answer 3

Correct Answer: D

Question 4

Which configuration step is necessary when automatic updating is required of iOS apps provisioned through Systems Manager that are found in the App Store?

A.
Create a profile with automatic update enabled and apply it to iOS devices.
B.
Create a security policy that enables automatic updates.
C.
No configuration step is necessary; automatic updating is the default behavior.
D.
Configure automatic updating of iOS devices in the Meraki installed profile.

Answer 4

Correct Answer: B

Question 5

For an AP that displays this alert, which network access control method must be in use?

A.
preshared key
B.
MAC-based access control with RADIUS server
C.
WPA2-enterprise with my RADIUS server
D.
splash page with my RADIUS server

Answer 5

Correct Answer: A

Question 6

When wireless SSIDs are configured in Dashboard, which setting on the Access Control page affects the ability of a 2.4 GHz only client device from associating to the WLAN for the first time?

A.
Dual band operating with Band Steering
B.
Content filtering
C.
802.11r
D.
Bridge mode

Answer 6

Correct Answer: A

Question 7

Air Marshal has contained a malicious SSID.
What are two effects on connectivity? (Choose two.)

A.
New clients can connect.
B.
Currently associated clients are disconnected.
C.
Currently associated clients are affected by restrictive traffic shaping rules.
D.
Currently associated clients stay connected.
E.
New clients cannot connect.

Answer 7

Correct Answer: B,E

Question 8

Which requirement is needed to implement Fast Lane on Cisco Meraki APs?

A.
adaptive 802.11r disabled
B.
wireless profile installed on an Apple iOS device
C.
wireless profile installed on a Cisco iOS access point
D.
traffic shaping rule tagging traffic with a DSCP value of 46 to Apple.com

Answer 8

Correct Answer: B

Question 9

Which three verbs of request are available in the Cisco Meraki API? (Choose three.)

A.
PATCH
B.
PUT
C.
POST
D.
SET
E.
ADD
F.
GET

Answer 9

Correct Answer: B,C,F

Question 10

Where should a network admin navigate to investigate wireless mesh information between Meraki APs?

A.
Wireless > Monitor > RF Spectrum
B.
Wireless > Monitor > Access Points > AP > RF
C.
Wireless > Monitor > Wireless Health
D.
Wireless > Configure > Radio Settings

Answer 10

Correct Answer: B