Practice Tests Flashcards

1
Q

List 3 types of measuring tools used in the shop:

A

Rules, tapes, specialty measuring devices

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

To adjust the blanks and patterns for growth, what do you remove ?

A

1/16th per joint

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

The net pattern lines are created on a blank that has been cut to size by:

A

Marking the allowances

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What are the 2 adjustments that need to be checked when using the break?

A

The distance between the top leaf and folding leaf.

The clamping pressure

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

When using the box and pan break, the operator should always what?

A

Check the alignment of the fingers to ensure that’s they are straight

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Over bending of material in the break is done to compensate for what?

A

Spring back

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

The allowances on curved cheeks are:

A

3/16”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Cheeks with straight sides may have the male Pittsburgh allowance of:

A

1/4”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

To properly notch the allowance of a runner that will be broken, the notch should be:

A

To the net pattern

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

On a slip and roll forming machine, the roll is set to form the amount of curve is the:

A

Rear roll

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Y-Branches and larger fittings may require a ____

A

2 piece heel

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

When folding the 1/2” fold on fittings to accept a drive cleat, a ______ may not be used

A

Cheek bender

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

To prevent damage to the folding leaf when forming a hammerlock, it is necessary to relieve the material used for the _____ of the Pittsburgh lock

A

Pocket

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

What are 4 advantages that the proprietary duct connection offers over a standing drive connection

A

Fabrication is simplified.

The joint has more rigidity

The joint makes a better seal

Net patterns are only required

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Before attempting to assemble the Pittsburgh lock, it is important to ensure that:

A

The lock is open and loose enough to accept the hook

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Tacking a Pittsburgh seam refers to what?

A

Folding the flange over at intervals

17
Q

When assembling a slip and drive joint, the drive cleat goes in the what?

A

Folded side

18
Q

When bending over the hammerlock flange, the flange should be _____ by placing the project on a bench

19
Q

Flexible duct connection is used to:

A

Isolate HVAC equipment from ductwork

20
Q

What is the maximum length of a fire damper sleeve with breakaway connections ?

A

Fire separation wall plus 6” on both sides

21
Q

A fire damper may be adjusted or modified to fit odd sized ductwork if:

A

Never, they are all ULC rated

22
Q

A fire damper sleeve required for a 8X8 duct line. What size does the damper need to be?

23
Q

Edge distance refers to the distance between the edge of the material and the ______ of the fastener that will be used to secure the seam

24
Q

The minimum recommended edge distance for fasteners is:

A

2 times the fastener diameter

25
Thicker metal will allow a ______ pitch to be used
Larger
26
Why are lap seams not spot welded at the ends first to hold them in place while fabricating the seam?
Buckling may occur
27
What is the advantage of rivets over screws or bolts ?
They are a more permanent manner
28
The pop rivet is a type of:
Blind rivet
29
What is the allowance for grooved seams which are lighter than 22Gauge?
(3W) three times the width of the seam
30
When setting the fingers of the barfolder, the fingers should be set at:
The width of the seam minus 2 metal thicknesses
31
After hooking the folded edges of the grooved seam together, you should:
Set the seam tight
32
How many breaks on a rectangular hammerlock ?
3
33
The pocket will not change with the adjustment of the feed guide. The pocket will always be what size?
3/8” deep