Part 3 Flashcards

1
Q

Refer to the exhibit. An engineer is configuring an EtherChannel between Switch1 and Switch2 and notices the console message on Switch2. Based on the output, which action resolves this issue? pic 88 A. Configure more member ports on Switch1. B. Configure less member ports on Switch2. C. Configure the same port channel interface number on both switches. D. Configure the same EtherChannel protocol on both switches.

A

D. Configure the same EtherChannel protocol on both switches

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Refer to the exhibit. A network engineer configures NAT on R1 and enters the show command to verify the configuration. What does the output confirm? A. The first packet triggered NAT to add an entry to the NAT table. B. R1 is configured with NAT overload parameters. C. A Telnet session from 160.1.1.1 to 10.1.1.10 has been initiated. D. R1 is configured with PAT overload parameters. pic 89

A

A. The first packet triggered NAT to add an entry to the NAT table.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Refer to the exhibit. What is the cause of the log messages? A. OSPF area change B. MTU mismatch C. IP address mismatch D. hello packet mismatch pic 90

A

A. OSPF area change

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Refer to the exhibit. An engineer implemented several configuration changes and receives the logging message on Switch1. Which action should the engineer take to resolve this issue? A. Change Switch2 to switch port mode dynamic auto. B. Change the VTP domain to match on both switches. C. Change Switch1 to switch port mode dynamic auto. D. Change Switch1 to switch port mode dynamic desirable. pic 91

A

B. Change the VTP domain to match on both switches.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

pic 92

A

pic 93

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

94

A

95

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

pic 94 Refer to the exhibit. While troubleshooting a routing issue, an engineer issues a ping from S1 to S2. Which two actions result from the initial value of the TTL? (Choose two.) A. The packet reaches R2, and the TTL expires. B. R1 replies with a TTL exceeded message. C. The packet reaches R3, and the TTL expires. D. R2 replies with a TTL exceeded message. E. R3 replies with a TTL exceeded message. F. The packet reaches R1, and the TTL expires.

A

C. The packet reaches R3, and the TTL expires. E. R3 replies with a TTL exceeded message.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Refer to the exhibit. An engineer attempts to configure a trunk between switch SW1 and switch SW2 using DTP, but the trunk does not form. Which command should the engineer apply to switch SW2 to resolve this issue? A. switchport nonegotiate B. no switchport C. switchport mode dynamic desirable D. switchport mode access pic 95

A

C. switchport mode dynamic desirable

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Refer to the exhibit. What does the error message relay to the administrator who is trying to configure a Cisco IOS device? pic 96 A. The device received a valid NETCONF request and serviced it without error. B. The NETCONF running datastore is currently locked. C. A NETCONF request was made for a data model that does not exist. D. A NETCONF message with valid content based on the YANG data models was made, but the request failed.

A

C. A NETCONF request was made for a data model that does not exist.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What is the result when a technician adds the monitor session 1 destination remote vlan 223 command? pic 97 A. The RSPAN VLAN is replaced by VLAN 223. B. RSPAN traffic is sent to VLANs 222 and 223. C. An error is flagged for configuring two destinations. D. RSPAN traffic is split between VLANs 222 and 223.

A

A. The RSPAN VLAN is replaced by VLAN 223.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Refer to the exhibit. An engineer configures monitoring on SW1 and enters the show command to verify operation. What does the output confirm? pic 97 A. RSPAN session 1 is incompletely configured for monitoring. B. RSPAN session 1 monitors activity on VLAN 50 of a remote switch. C. SPAN session 2 monitors all traffic entering and exiting port FastEthernet 0/15. D. SPAN session 2 only monitors egress traffic exiting port FastEthernet 0/14.

A

A. RSPAN session 1 is incompletely configured for monitoring.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Refer to the exhibit. An engineer must add the SNMP interface table to the NetFlow protocol flow records. Where should the SNMP table option be added? pic 99 A. under the interface B. under the flow record C. under the flow monitor D. under the flow exporter

A

D. under the flow exporter

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Refer to the exhibit. An engineer must add the SNMP interface table to the NetFlow protocol flow records. Where should the SNMP table option be added? pic 99 A. under the interface B. under the flow record C. under the flow monitor D. under the flow exporter

A

D. under the flow exporter

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

An engineer must configure a SPAN session. What is the effect of the configuration? pic 100 A. Traffic received on VLANs 10, 11, and 12 is copied and sent to interface g0/1. B. Traffic sent on VLANs 10 and 12 only is copied and sent to interface g0/1. C. Traffic sent on VLANs 10, 11, and 12 is copied and sent to interface g0/1. D. Traffic received on VLANs 10 and 12 only is copied and sent to interface g0/1.

A

A. Traffic received on VLANs 10, 11, and 12 is copied and sent to interface g0/1.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

These commands have been added to the configuration of a switch. Which command flags an error if it is added to this configuration? pic 101 A. monitor session 1 source interface port-channel 6 B. monitor session 1 source vlan 10 C. monitor session 1 source interface FastEthemet0/1 rx D. monitor session 1 source interface port-channel 7, port-channel 8

A

B. monitor session 1 source vlan 10

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Refer to the exhibit. Cisco DNA Center has obtained the username of the client and the multiple devices that the client is using on the network. How is Cisco DNA Center getting these context details? pic 102 A. Those details are provided to Cisco DNA Center by the Identity Services Engine. B. The administrator had to assign the username to the IP address manually in the user database tool on Cisco DNA Center. C. Cisco DNA Center pulled those details directly from the edge node where the user connected. D. User entered those details in the Assurance app available on iOS and Android devices.

A

A. Those details are provided to Cisco DNA Center by the Identity Services Engine.

17
Q

Refer to the exhibit. What is required to configure a second export destination for IP address 192.168.10.1? A. Specify a different UDP port. B. Specify a different TCP port. C. Configure a version 5 flow-export to the same destination. D. Specify a different flow ID. E. Specify a VRF. pic 103

A

A. Specify a different UDP port.

18
Q

Refer to the exhibit. After implementing the configuration, 172.20.20.2 stops replying to ICMP echos, but the default route fails to be removed. What is the reason for this behavior? A. The threshold value is wrong. B. The source-interface is configured incorrectly. C. The destination must be 172.30.30.2 for icmp-echo. D. The default route is missing the track feature. pic 104

A

D. The default route is missing the track feature.

19
Q

Which privilege level is assigned to VTY users? A. 1 B. 7 C. 13 D. 15 pic 105

A

A. 1

20
Q

The login method is configured on the VTY lines of a router with these parameters: ג€¢ The first method for authentication is TACACS ג€¢ If TACACS is unavailable, login is allowed without any provided credentials Which configuration accomplishes this task? pic 107

A

D pic 108

21
Q

Which method does the enable secret password option use to encrypt device passwords? A. MD5 B. PAP C. CHAP D. AES

A

A. MD5

22
Q

On which protocol or technology is the fabric data plane based in Cisco SD-Access fabric? A. VXLAN B. LISP C. Cisco TrustSec D. IS-IS

A

A. VXLAN

23
Q

What is the difference between the enable password and the enable secret password when service password encryption is enabled on an IOS device? A. The enable secret password is protected via stronger cryptography mechanisms. B. The enable password cannot be decrypted. C. The enable password is encrypted with a stronger encryption method. D. There is no difference and both passwords are encrypted identically.

A

A. The enable secret password is protected via stronger cryptography mechanisms.