NEW Flashcards
1.) serviceability limits for turbine blades are much more stringent than those for turbine nozzles vanes 2.) a limited number of small nicks and dents can usually be permitted in any area of a turbine blade. REGARDING THE ABOVE STATEMANT,
only no. 1 is true
the breaking loose of small pieces of metal from coated surfaces, usually caused by defective plating or excessive loads, is called
Flaking
What publication contains the mandatory replacement time for parts of a turbine engine?
ENGINE MANUFACTURER’S SERVICE INSTRUCTIONS
Which of the following components inspections is to be accomplished on 100-hour inspection?
Check cylinder compression
Each power plant installed on an airplane with a standard airworthiness certificate must have be?
Type certificated
Where would one find type design information for an R1830-92 engine certificated under the Civil Air Regulation (CAR) and installed on a DC-3?
The aircraft engine specification
On a reciprocating engine aircraft using a shrouded exhaust muffler system as a source for cabin heat, the exhaust system should be
VISUALLY INSPECTED FOR ANY INDICATION OF CRACKS OR AN OPERATIONAL CARBON MONOXIDE DETECTION TEST SHOULD BE DONE
Select the Airworthiness Directives applicability statement which applies to an IVO-355 engine, serial number T8164, with 2,100 hours’ total time and 300 hours since rebuilding
APPLIES TO ALL IVO-355 ENGINES, SERIAL NUMBERS T8000 THROUGH T8300, HAVING LESS THAN 2,400 HOURS’ TOTAL TIME
What is ATA iSpec 2200?
STANDARDIZED ELECTRONIC DOCUMENTATION FOR AN AIRCRAFT MODELS
You are performing a 100-hour inspection on an R985-22 aircraft engine. What does the ‘985’ indicate?
THE TOTAL PISTON DISPLACEMENT OF THE ENGINE
Straightening nitrided crankshafts is
Not recommend
Indentations on bearing races caused by high static loads are known as
Brinelling
How is the flow range of the fuel discharge nozzles installed in a fuel injected reciprocating engine indicated?
BY A LETTER STAMPED ON THE HEX OF THE NOZZLE BODY
What section in the instruction for continued airworthiness is FAA approved?
Airworthiness limitations section
The airworthiness standards for the issue of type certificates for small for small airplanes with nine or less passenger seats in the normal, utility, and acrobatic categories may be found in the
FEDERAL AVIATION REGULATIONS, PART 23
What regulations are covered by 14 CFR part 1
Definitions and abbreviation
Change to the hub design is?
Propeller major modification
Fabrication performed in the wing main ribs and compression members is a (IS: 5.1.1.2)
Airframe major repair
Rewinding the field coil of an electrical accessory is an example of?
Appliance major repair
What is the regulatory definition of preventative maintenance?
SIMPLE OR MINOR PRESERVATION OPERATIONS AND THE REPLACEMENT OF SMALL STANDARD PARTS, NOT INVOLVING COMPLEX ASSEMBLY OPERATIONS
A special flight permit may be issued for an aircraft that may not currently meet applicable airworthiness requirement, but is capable of safe flight when: 1. Flying the aircraft to a base where repairs, alterations, or maintenance are to be performed, or to a point of storage. 2. Delivering or exporting the aircraft. 3. Production flight testing new production aircraft. 4. Evacuating aircraft from areas of impending danger. 5. Conducting customer demonstration flights in new production aircraft that have completed production flight tests. WHICH STATEMENTS ARE CORRECT?
ALL OF THE STATEMENT ARE CORRECT
Airworthiness Directives (ADs) are designed to notify the
Aircraft owners and other interested persons of unsafe conditions and prescribes the condition under which the product may continue to be operated
No person or entity, other than the Authority, may approved an aircraft, airframe, aircraft engine, propeller, appliance, or component part for return to service after it has undergone maintenance, preventive maintenance, rebuilding, or modification, except as provided in the following
All of the choices are correct
Conversions of any sort for the purpose of using fuel of a rating or grade other than that listed in the engine specifications is (Part IS 5.1.1.2)
Powerplant major modification
Which is considered to be typical preventive maintenance operations (Part IS 5.1.1.2)
All of the choices are correct
Removal of accessories that are listed as required equipment on the aircraft or engine specification is an example of?
Powerplant major modification
Each person performing a major repair or major modification shall forward a copy of the form to the Authority, in accordance with Authority instructions, after the aeronautical product is approved for return to service within
48 hrs
Removal, installation, and repair of landing gears in PCAR 5.1.1.2 is ?
Preventive maintenance
Which statement is correct regarding an aircraft that is found to be not airworthy after an annual inspection, due to an item requiring a major repair? (assuming the approved data is issued to accomplish the repair
ans: AN APPROPRIATELY RATED MECHANIC MAY ACCOMPLISH THE REPAIR AND AN IA MAY APPROVED THE AIRCRAFT FOR RETURN TO SERVICE
Radio equipment installation made in accordance with the Supplemental Type Certificate data require approval for return to service
ans; BY THE HOLDER OF AN INSPECTION AUTHORIZATION
Who is authorized among the following to perform preventive maintenance, repair, or alteration on civil aircraft of the Philippines registry?
All of the choices are correct
The positive aspects of human factor issues are referred to as the
Magnificent seven
How is the quality system assured?
ans; BY AN INTERNAL REPORTING AND AUDITING SYSTEM
What part of the Federal Aviation Regulation prescribes the requirements for issuing mechanic certificates and associated ratings and the general operating rules for the holders of these certificates and rating?
14CFR PART 65
What is the maximum duration of a temporary airman certificate?
120 days
The “SHEL” model is another human factors tool. The goal is to determine not only what the problem is, but also
ans; WHERE AND WHY IT EXISTS
Instrument repairs maybe performed
ans; BY AN FAA-APPROVED INSTRUMENT REPAIR STATION
Certificated mechanics with a powerplant rating may perform
ans; 100-HOUR INSPECTIONS REQUIRED BY THE FEDERAL AVIATION REGULATION ON POWERPLANT, PROPELLER OR ANY COMPONENTS THEREOF, AND MAY RELEASE THE SAME SERVICE
The replacement of fabric on fabric covered parts such as wings, fuselages, stabilizers, or control surface is considered to be a
ans; MAJOR REPAIR EVEN THOUGH NO OTHER ALTERATION OR REPAIR IS PERFORMED
The three types of human error are
ans; OMISSION, COMMISSION, AND EXTRANEOUS
Which of these publications contains standards for protrusion of bolts, studs, and screws, through self-locking nuts?
ans; AC 43.13.-1B
According to Dr. James Reason, there are two types of human failure that can occur. They are:
Active and latent
How long does the holder of a certificate issued under 14 CFR part 65 have to notify the FAA after any change in permanent mailing address?
30 days
The replacement of a damaged engine mount with a new identical engine mount purchased from the aircraft manufacturer is considered a
Minor repair
Certificated mechanics, under their general certificate privileges, may
ans; PERFORM A 100-HOUR INSPECTION OF INSTRUMENTS
John and Nancy have been tasked with completing a hydraulic pump inspection. John is 5 feet 9 inches tall. Nancy is 5 feet 6 inches tall. What could result if Nancy is not tall enough to accomplish the task?
Human error
Which of the following is an instance when a special flight permit may not be issued?
ans; FLYING PASSENGERS ON A SCHEDULED OPERATION
14 CFR Part 65 contains information for the certification of
ans; AIRMEN OTHER THAN FLIGHT CREWMEMBERS
14 CFR Part 65 Subpart D contains regulation regarding the certification of
Mechanics
You are performing a 100-hour inspection on an R985-22 aircraft engine. What does the ‘985’ indicate?
ans; THE TOTAL PISTON DISPLACEMENT OF THE ENGINE
What is ATA iSpec 2200?
ans; STANDARDIZED ELECTRONIC DOCUMENTATION FOR AIRCRAFT MODELS
Owners for operators of airplane over 5700 kg and helicopters over 3175 maximum take-off weight shall report to the Authority and to the organization responsible for the aircraft type design any failure, malfunction, or defect be made within
3 working days
What does acronym TSO mean regarding a type certificated aircraft part, material, component and/or process?
ans; TECHNICAL STANDARD ORDER
An applicant for an AMT license for Powerplant and Airframe ratings relying solely on practical experience shall provide documentary evidence of
ans; 60 MONTHS OF PRACTICAL EXPERIENCE
What is the regulatory definition of preventive maintenance?
ans; SIMPLE OR MINOR PRESERVATION OPERATIONS AND THE REPLACEMENT OF SMALL STANDARDS PARTS , NOT INVOLVING COMPLEX ASSEMBLY OPERATIONS
Refinishing decorative coating of fuselage, wings, tail groups surfaces (excluding balanced control surfaces), fairings, cowlings, interior when removal or disassembly of any primary structure or operating system is not required is
Preventive maintenance
A holder of an AMT license desiring to renew must accomplish and submit the requirements within how many days prior to the expiry of his/her license?
30 days
Which part of Philippine Civil Aviation Regulation prescribes the requirements for certification of an aircraft and aeronautical components for continuing airworthiness?
PCAR PART 5
Rewinding the field coil of an electrical accessory is an example of?
Appliance major repair
In compliance with the recent experience requirements, a licensed AMT may not exercise the privileges of his/her license or rating unless he/she served as an AMT under his/her licensed and ratings for at least 6 months within the preceding
24 months
All Philippine registered aircraft used for commercial or aerial work operations shall be re-weighted
Every 3 years
All Philippine aircraft used in general aviation shall be re-weighed
Every 5 years
An AMT or specialist who seeks reinstatement of his/her license that has already expired for 24 months from expiration date shall
ans; PASS THE CIVIL AVIATION REGULATIONS TEST AND MUST UNDERGO THE APPROPRIATE RECURRENT TRAINING FROM AN APPROVED MAINTENANCE ORGANIZATION OR ANY SCHOOL OR FACLITY BY THE AUTHORITY FOR SUCH PURPOSE
The Contracting State which approved the original type certificate and any subsequent supplemental type certificate for an aircraft, or which approved the design of an aeronautical product or appliance.
State of design
Who is responsible for ensuring that all maintenance required to be carried out in the hangar plus any defect rectification carried out during base maintenance, is carried out to specified design and quality standards?
Line maintenance
The restoration of an aircraft/ aeronautical product by using methods, techniques, and practices acceptable to the authority, when it has been disassembled, cleaned, inspected as permitted, repaired as necessary, reassembled, and tested to the same limits as a new item, using either, new parts or used parts that conform to new part tolerances and limits
Rebuild
Who is authorized to repair an aircraft instrument?
ans; CERTIFIED REPAIR STATION APPROVED FOR THAT INSTRUMENT
A certification confirming that the maintenance work to which it relates has been complied with in accordance with the applicable standards of airworthiness using approved data
Maintenance release
PCAR’s part for MRO/AMO is
PCAR PART 6
How long is a mechanic certificate with an airframe and/or powerplant ratings valid?
ans; UNTIL SURRENDERED, SUSPENDED, OR REVOKED
The approved maintenance training organization (AMO) shall relive the person performing maintenance functions from all duties for 24 hours after working for
ans; 7 CONSECUTIVE DAYS
Many areas of aviation have shifted their focus from eliminating error to
Preventing and managing error
Why is a mechanic applicant issued a temporary certificate after successful completion of the required tests?
ans; TO ALLOW FOR REVIEW OF HIS/HER APPLICATION SUPPLEMENTARY DOCUMENTS
who is responsible for for determining that materials used in aircraft maintenance and repair are of the proper type and conform to the appropriate standards?
ans; THE INSTALLING PERSON OR AGENCY
