Brainscape's Knowledge GenomeTM

Browse over 1 million classes created by top students, professors, publishers, and experts.


See full index

AIRLAW > I > Flashcards

I Flashcards

1
Q

During an annual inspection, if a defected which makes the aircraft UN AIRWORTHY the person must

A

Provide a written notice of the defect tp the owner

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

REPAIR MADE ON THE HYDRAULIC/PNEUMATIC systems is concerned

A

Airframe minor repair

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

When major repair alteration results in any changes in the aircraft operating limitations or data contained in approved airplane flight manual appropriate AMENDMENT to the aircraft operating limitations shall be made in

A

The form and manner prescribe by the CAAP

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

A PERMANENT RECORD OF EVERY MAINTENANCE (not including prevent maintenance)repair of building or alterations on any airframe,powerplant, or appliances should be maintained by

A

The registered operator

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Where is the RECORD of compliance with Airworthiness directives or manufacturer SERVICE BULLETINS NORMALLY INDICATED?

A

Aircraft maintenance record

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

ANY REPAIR TO SPAR RIBS,and surface involves

A

Airframe minor repair technique

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Strengthening or reinforcing the fuselage longeron

A

Airframe major repair

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

When, TAXIING AN AIRPLANE with a quartering tailwind, the elevator should be

A

Upwind aileron should be in the down position

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Which is an appliance major repair

A

Overhaul of a hydraulic pump

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Which of the ff is considered to typical preventive maintenance

A

Removal, installation and repair of landing gears tires

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Airframe shall mean

A

Any and any kinds of booms, landing gears, empennages, fairing, or control of any and all kinds of fuselage,booms, empennages, nacells, cowling ,control surfaces

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

AIRWORTHINESS DIRECTIVES are issued primarily to

A

Correct and unsafe condition

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

PRIMARY RESPONSIBILITY for compliance with AIRWORTHINESS DIRECTIVES lies with the

A

Aircraft owner or operator

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

An aircraft TYPE CERTIFICATE DATA SHEETS contains

A

Location of the datum

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

When an AIRWORTHY (AT THE TIME OF SALE) AIRCRAFT IS SOLD, THE AIRWORTHINESS CERTIFICATE

A

Is transferred with the aircraft

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

The ISSUANCE OF AN AIRWORTHINESS CERTIFICATE is governed by

A

14 CFR PART 21

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

Where are TECHNICAL DESCRIPTION OF CERTIFICATED PROPELLER FOUND

A

Propeller type certificate data sheets

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

What information is generally contained in AIRCRAFT SPECIFICATIONS OR TYPE CERTIFICATE DATA SHEETS

A

Control surface movements

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

PLACARDS required on an aircraft are specified in

A

Aircraft specifications or type certificate data sheets

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

Technical information about OLDER AIRCRAFT MODELS ,of which no MORE THAN 50 REMAIN IN SERVICE, can be found in the

A

Aircraft listing

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

Which regulations provide information regarding instrument range MARKINGS FOR AN AIRPLANE CERTIFICATED in the normal category

A

14 CFR part 23

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

Which regulations provide the AIRWORTHINESS STANDARD FOR AN AIRPLANE CERTIFICATED in the normal category

A

14 CFR PART 23

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

What is the MAINTENANCE RECORDING RESPONSIBILITY of the person who complies with an Airworthiness directive

A

Make an entry in the maintenance record of that equipment

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
Q

AVIATION MAINTENANCE ALERTS (formerly general aviation airworthiness alerts)

A

Provide information about aircraft problems and suggested corrective actions

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
25
Q

(refer to figure 62,62a and 62b as necessary) which doubler require HEAT TREATMENT BEFORE INSTALLATION

A

-102

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
26
Q

How many parts will need to be fabricated by the mechanic in the construction and INSTALLATION OF ONE DOUBLER

A

3

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
27
Q

Using only the information given (when BEND ALLOWANCE,set back , etc.have been calculated )which doubler is it possible to construct and install

A

-101

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
28
Q

Type certificate data sheets are issued for which of the ff products

A

Aircraft, engines and propellers

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
29
Q

How long are AD compliance record required to be kept

A

They shall be retained,and then transferred with the aircraft when it is sold

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
30
Q

What does the type certificate data sheets DESIGNATION CODE ‘2 PCSM’ mean

A

Two place(number of seats), closed, sea, monoplane

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
31
Q

Which of the ff includes all the regulatory definitions of ‘maintenance’

A

Overhaul,repair,parts replacement, inspection, and preservation

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
32
Q

What is the maximum penalty for cheating or other unauthorized conduct when taking a FAA mechanic test

A

ineligibility to receive amy certificate or rating for 1 year, and suspension or revocation of any certificate held

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
33
Q

UNDER FEDERAL AVIATION REGULATIONS,an aviation maintenance technician is required to perform maintenance on an aircraft so that it

A

Atleast equal to its original or properly altered condition

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
34
Q

A repair,as performed on an airframe, shall mean

A

The restoration of the airframe to a condition for safe operation after damage or DETERIORATION

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
35
Q

The REPLACEMENT OF FABRIC ON FABRIC COVERED parts such as wings, fuselage, stabilizer, or control surfaces is considered to be a

A

Major repair even though no other alteration or repair is performed

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
36
Q

Which is classified as a major repair

A

The splicing of skin sheets

37
Q

The 100 hrs inspection required by federal aviation regulations for certain aircraft being operated for hire may be performed by

A

Appropriately rated mechanics and approved by them to return to service

38
Q

A person working under the supervision of a certificated mechanic with an airframe and powerplant rating is not authorized to perform

A

100 hrs inspection

39
Q

What is means by which the FAA notifies aircraft owners and other interested persons of unsafe conditions and prescribes the condition under which the product may continue to be operated?

A

Airworthiness directives

40
Q

Which is an appliance major repair

A

Overhaul of hydraulic pressure pump

41
Q

Which maintenance action is an airframe major repair

A

Repair portion of skin sheets by making additional seems

42
Q

Which aircraft record entry is the best description of the replacement of several damaged heli coils in a casting

A

Eight 1/4-20 inch standard heli coils were replaced. The damaged inserts were extracted the tapped holes gaged, then new inserts intalled and tags removed

43
Q

Which statement is true regarding the requirements for maintenance record format?

A

Any format that provides record continuity and includes the required information may be used

44
Q

When a 100 hrs inspection is completed, if separate maintenance records for the airframe, powerplant and propellers are maintained where is the entry for the inspection recorded?

A

In each record

45
Q

For aircraft operated under part 91 when is aircraft total time required to be recorded in aircraft maintenance records?

A

After satisfactory completing maintenance, preventive maintenance, rebuilding, and alterations(including inspection)

46
Q

If more space is needed for a work description entered on FAA form 337, what information should be included on the attached sheets in addition to the rest of the work description?

A

Aircraft nationality and registration mark,and the date the work was accomplished

47
Q

Which aircraft record entry nest describes a repair of a dent in a tubular steel structure dented at a cluster

A

Welded a reinforcing plate over the dented area

48
Q

Who is responsible for making the entry in the maintenance records after an annual, 100 hrs or progressive inspection

A

The person approving or disapproving for return to service

49
Q

A certificated mechanic without an inspection authorization who signs the appropriate block on FAA form 337 is doing what

A

Certifying that the work was done in accordance with the requirements of CFR part 43

50
Q

For aircraft operated under part 91, which of the following records must be retained and transferred with the aircraft when it is sold

A

Records of the current status of applicable AD’s and date and time when recurring AD’S are next due

51
Q

An aircraft owner was provided a list of discrepancies on an aircraft that was not approved for return to service after an annual inspection. Which of the ff statement is/are true concerning who may correct discrepancies
1 Only a mechanic with an inspection authorization
2 an appropriately rated mechanic
3 any certificate repair station

A

2

52
Q

When a discrepancy list is provided to an aircraft owner or operator after an inspection it says in effect that

A

Except for those discrepancies the item inspected is AIRWORTHY

53
Q

In order to reconstruct lost or destroyed aircraft maintenance records, what is it necessary to establish

A

Total time in service of the airframe

54
Q

For aircraft operated under part 91 which of the ff records must be retained for at least one year, or until the work is repeated or superseded?

A

Records of maintenance, alternations, preventive maintenance, 100 hrs ,annual,and progressive inspection

55
Q

For aircraft operated under part 91 which difference is there,if any, between the record entry requirements for maintenance (repair or alteration)and the record entry requirements for inspection (beyond the description of the work performed and the type and extent of inspection)?

A

Aircraft total time is required to be included only in the inspection entry

56
Q

Which maintenance record entry best describes the action taken for a 125 inch deep dent in a straight section of 1/2 inch aluminum alloy tubing

A

Dented section removed and replaced with identical new tubing flared to 37 degrees

57
Q

Which maintenance record entry best describes the action taken for a control cable showing approximately 20 percent wear on several of the individual outer wires at a fairlead

A

Wear within acceptable limits repair not necessary

58
Q

What is/are the appropriate action concerning minor repair performed on a certificated aircraft?
1 FAA form 337’s must be completed
2 entries must be made in the aircraft maintenance record
3 the owner of the aircraft must submit a record of all minor repairs

A

2

59
Q

When work is performed on an aircraft that necessities the use of FAA form 337 who should prepare the form?

A

The person who performs of supervises the work

60
Q

What is the status of data used as a basis for approving minor repairs or alterations for return to service?

A

Data must be FAA approved prior to its use for that purpose

61
Q

Which statement is true regarding the use of FAA form 337

A

FAA form 337 is not authorized for use with other than U S registered aircraft

62
Q

After making a certain repair to an aircraft engine that is to be returned to service, an FAA form 337 is prepared.How many copies are required and what is the disposition of the completed forms

A

Two ; one copy for the aircraft owner and one copy for the FAA

63
Q

Show is responsible for upkeep of the required maintenance records for an aircraft

A

The aircraft owner

64
Q

An aircraft was not approved for return to service after an annual inspection and the owner wanted to fly the aircraft to another maintenance base which statement is correct

A

The owner must obtain a special flight permit

65
Q

Each person performing an annual or 100 hrs inspection shall use a checklist that contains at least those items in the appendix of

A

14 CFR part 43

66
Q

An FAA Form 337 is used to record and documents

A

Major repair and major modification

67
Q

After a mechanic holding an airframe and powerplant rating completes 100 hour inspection, what action is required before the aircraft is returned to service

A

Make the proper entries in the maintenance record

68
Q

Which of the ff may a certified airframe and powerplant mechanic perform on aircraft and approve for return to service
1 A 100hrs inspection
2 an annual inspection,under specified circumstances
3 A progressive inspection under specified circumstances

A

1and 3

69
Q

A cessna 180 aircraft has a McCauley propeller model no. 2A34C50/90A. The propeller is severely damaged in a ground accident and this model propeller is not available for replacement. Which of the following should be used to find an approved alternate replacement?

A

Aircraft specifications/type certificate data sheets

70
Q

Which of the following is used to monitor the mechanical integrity of the turbines as well as to check engine operating conditions of a turbine engine?

A

Exhaust gas temperature

71
Q

On a reciprocating engine aircraft using a shrouded exhaust muffler system as a source for cabin heat the exhaust system should be

A

Visually inspected for any indication of cracks or an operational carbon monoxide detection test should be done

72
Q

Which of the following contains a minimum checklist for 100 hrs inspection of engine

A

24 CFR part appendix D

73
Q

When must an Airworthiness directive (AD) be complied with after it becomes effective

A

As specified in a AD

74
Q

Which of the following contains a table that list the engine to which a given propeller is adaptable

A

Propeller type certificate data sheets

75
Q

Which of the following components inspection is to be accomplished on a 100 hrs inspection?

A

Check cylinder compression

76
Q

You are performing a 100 hrs inspection on an R985-22 aircraft engine. What does the 985 indicate?

A

The total piston displacement of the engine

77
Q

Where would one find type design information for an R1830-92 engine certificated under the civil air regulations (CAR) and installed on DC -3?

A

The aircraft engine specification

78
Q

Straightening nitrided crankshaft is

A

Not recommend

79
Q

The breaking loose of small pieces of metal from coated surfaces usually caused by defective plating or excessive loads is called

A

Flaking

80
Q

Each powerplant installed on an airplane with a standard Airworthiness CERTIFICATE must have been

A

Type certificate

81
Q

A severe condition of chafing or fretting in which a transfer of metal from one part to another occurs is called

A

Galling

82
Q

Indentations on bearing races caused by high STATIC LOADS are known as

A

Brinelling

83
Q

When inspection an aircraft reciprocating engine what documents is used to determine if the proper magnetos are installed

A

Aircraft engine specification or type certificate data sheets

84
Q

Which of the following can inspect and approve an engine major repair for return to service

A

Certificated mechanic with inspection authorization

85
Q

What publication is used for guidance to determine whether a powerplant repair is major or minor

A

FEDERAL AVIATION REGULATIONS Part 43, appendix A

86
Q

The Airworthiness standards for the issue of type certificate for small airplanes with nine or less passenger seats in the normal utility and acrobatic categories may be found in the

A

Federal aviation regulations,part 23

87
Q

Which of the ff contains approved data for performing a major repair to an aircraft engine?

A

Manufacturer maintenance instructions when FAA approved

88
Q

What maintenance records is/are required following a major repair of an aircraft engine?

A

Entries in the engine maintenance record and FAA form 337

89
Q

A ground incident that results in propeller sudden stoppage would require a crankshaft run out inspection. What publication would be used to obtain crankshaft run out tolerance?

A

Current manufacturer maintenance instructions

AIRLAW (5 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2024 Bold Learning Solutions. Terms and Conditions