Misc Equipment

Question 1

Leica DISTRO D330i is programmed to measure from the back of the unit? T/F

Answer 1

True

Question 2

Correct Menu settings for the Lumix Point and Shoot Camera Menu are?

Answer 2

5M (Picture Size), Fine (Quality), and LED Light Off (Motion Picture menu).

Question 3

Lumix Point and Shoot Camera Low-Light Procedure is:

Answer 3

Tripod required, SCN on dial, Starry Sky with cursor, select either 30 or 60 seconds.

Question 4

FLIR i60 can be used as a digital camera? T/F

Answer 4

True (Select Digital Camera under Menu).

Question 5

FLIR i60 is set to the following defaults by the technician:

Answer 5

Camera: Infrared
Measurement: Temperature
Color palette: Iron
Settings: F, 24h, High, and 32-662 (Temperature range)

Question 6

360 Camera System setting are:

Answer 6

Manual Exposure (M), Large Image (L), White Balance on Auto (A), Focus Mode Switch to Manual (M)

Question 7

The Focus Mode Switch on the 360 Camera System is located near the display? T/F

Answer 7

F- Camera front by the lens.

Question 8

To set the exposure on the 360 Camera System rotate the _____ ____ while observing the exposure scale in either the ________ _________ or Viewfinder.

Answer 8

Control Dial; Control Panel; Viewfinder

Question 9

PTGui Pro software requires the lens type to be set to ___ ____ and Field of View to ___degrees.

Answer 9

Circular Fisheye; 185

Question 10

The proper format for the file produced by PTGui Pro software is ______ __ ___.

Answer 10

Quicktime VR (.mov)

Question 11

The MiniMIRAIII detects what signals on MULTIBAND?

Answer 11

Microwave (S, C, X, & K), Ultrasonic (U)

Question 12

WIFI can cause false signals on which two bands on the MIRA?

Answer 12

S and C

Question 13

On the MIRA, X and K may falsely indicate positive due to?

Answer 13

Police Radar

Question 14

EMR Detector batteries are installed with the positive terminal toward the front of unit? T/F

Answer 14

True

Question 15

To calibrate the EMR Detector, the unit is placed between the Item of Interest and other potential EMR sources, then turned on. After verifying lamp test, ensure the orange/blue “Heartbeat” LED pulses every _ seconds. Ensure detector enters “Calibration” mode lasting ____ seconds and ending with rapid ___-tone pulse.

Answer 15

2; 10; 4.

Question 16

Suggested rate of scan with the EMR Detector after locating a source is _ in/sec.

Answer 16

2

Question 17

On the Mini MIRAIII pressing the letter button on the left does what?

Answer 17

Enters Single Band Mode for the selected band.

Question 18

On the Mini MIRAIII pressing the speaker button on the right does what?

Answer 18

Disables audio indicator for selected band.

Question 19

The 2 LED’s on top of the IR Wand handle indicate what?

Answer 19

One for each side of wand; Color indicates signal strength (green, amber, and red); Indicates direction of transmitter.

Question 20

How do you adjust screen brightness on the MiniMIRAIII?

Answer 20

Press and hold center of MULTI BAND or SINGLE BAND screens and a slider bar will appear; Continue to press screen and slide your finger up or down to adjust brightness.

Question 21

The Peep Sight should be placed no closer than _ foot in front of the Grid Aim board?

Answer 21

1 foot

Question 22

The Stingray requires _ of water with the SiC packet or _ of water without the SiC packet.

Answer 22

1 liter, 1.4 liters.

Question 23

The Peep Sight can be placed closer the 1 foot to the Grid Aim board if necessary. T/F

Answer 23

True (8 inches)

Question 24

More than one length of hose maybe used between the water pressurized water source and the eductor. T/F

Answer 24

True

Question 25

How many lengths of hose can be added to the outlet of the eductor?

Answer 25

2.

Question 26

Angus Foaming requires the eductor knob to be set at _% not __% __?

Answer 26

6, 6 AR.

Question 27

The maximum IPC size that fits under the 8 foot Cube is _x_x_?

Answer 27

4',4',5'.

Question 28

Gelled Water Blocks weight __lbs when filled?

Answer 28

40.

Question 29

The software used to create stitch 360 photos is ____?

Answer 29

PTGui

Question 30

The Ricoh 360 camera can be used in low light? T/F

Answer 30

False, the Nikon camera must be used.

Question 31

The PSI required at the nozzle to achieve foam is?

Answer 31

35psi

Question 32

MIRA stands for?

Answer 32

Microwave, Infrared, and Acoustic

Question 33

The MIRA handheld unit detects ________ and ______.

Answer 33

Microwave; Acoustic

Question 34

The MIRA wand detects ______.

Answer 34

Infrared and can indicated the direction of the transmitter.

Question 35

The EMR detector alarms by ____, ____, and ____ LEDs accompanied by audio of varying ____ and ______.

Answer 35

Gren, Amber, Red; Speed, Intensity

Question 36

_____ non-linear reference points are seletected prior to the target when using Grid Aim.

Answer 36

5

Question 37

To verifiy Grid Aim target: XTK>Help>View Grid Board Map. T/F

Answer 37

True

Question 38

Do not use the vector adjustment on the tripod when aiming Grid Aim. T/F

Answer 38

True

Question 39

The Gimble Laser and copper hemisphere are used in precision targeting. T/F

Answer 39

True

Question 40

The Non-Newtonian fluid does what to Stingray velocity?

Answer 40

Slows

Question 41

The fastest smooth bore projectile for the PAN is?

Answer 41

X9