Misc.

Question 1

Chapter 1

Answer 1

index

Question 2

chapter 2

Answer 2

general info

Question 3

chapter 3

Answer 3

props

Question 4

chapter 4

Answer 4

apu

Question 5

chpt 5

Answer 5

masker emitter belts

Question 6

chpt 6

Answer 6

sub sonar systems

Question 7

chpt 7

Answer 7

ndt

Question 8

chpt 8

Answer 8

spu/spms

Question 9

chpt 9

Answer 9

rubber sonar domes

Question 10

chpt 10

Answer 10

diver tools

Question 11

chpt 11

Answer 11

wet and dry underwater welding

Question 12

chpt 12

Answer 12

cpp

Question 13

chpt 13

Answer 13

shaft lamination

Question 14

chpt 14

Answer 14

csa pods

Question 15

chpt 15

Answer 15

sea chests protection sleeves

Question 16

chpt 16

Answer 16

cofferdams

Question 17

chpt 17

Answer 17

inspections

Question 18

chpt 18

Answer 18

propulsion bearing

Question 19

chpt 19

Answer 19

iccp

Question 20

chpt 20

Answer 20

paint fairing compound

Question 21

chpt 23

Answer 21

pre deployment noise inspection

Question 22

chpt 24

Answer 22

fin stabilizer

Question 23

chpt 25

Answer 23

otaa

Question 24

chpt 26

Answer 24

cutting of sht

Question 25

chpt 27

Answer 25

hydro blasting

Question 26

chpt 28

Answer 26

pollution prevention

Question 27

chpt 29

Answer 27

sub procedures

Question 28

chpt 31

Answer 28

rudders

Question 29

220. Radcon Boundaries on a sub?

Answer 29

sail to the ensign

Question 30

221. Radcon Boundaries on a Carrier?

Answer 30

2 AND 3 ZONES

Question 31

222. What are the radcon requirements on diving on a nuclear vessel?

Answer 31

NO diving0-15min 15min-24 hr. 10 min max with epd and tld

Question 32

223. What side does a Carrier more up on? Why?

Answer 32

Starboard because nuclear discharge is on port side

Question 33

224. What are the Sonar pinging diving distances?

Answer 33

600 yrds hooded 1000yrds unhooded 3000yrds hatted

Question 34

225. What are the types of rudders?

Answer 34

Balanced, semi-balanced, unbalanced

Question 35

226. Where are the drain plugs found?

Answer 35

Bottom of the rudder

Question 36

227. What do you look for if you have bad actuation on the rudder?

Answer 36

The stock is free and clear

Question 37

228. What is the designed clearance for stock fairing on rudder and where do you measure?

Answer 37

3/8” from the 3 oclock and 9 oclock positions

Question 38

231. What are the distances for mooring up for ships and carriers?

Answer 38

4FT from pier and 6ft from bottom/ 20ft from pier 6ft from bottom for carriers

Question 39

232. List the PDR?

Answer 39

10-100

Question 40

233. List the FR?

Answer 40

1-4

Question 41

234. ORM Appendixes?

Answer 41

A 3 levels: deliberate/ time critical/ strategic B Assess the situation C Balance resources D Communicate E Do and debrief

Question 42

235. Advantages and disadvantages of Kerri cable

Answer 42

A: Less training, cut through all metal thickness, longer burn time, no electrical hazards after ingnited, only o2 needed D: tons of o2 needed, Will not cut rock or concrete

Question 43

236. 2 types of Cutting? Explain?

Answer 43

Oxy arc cutting and shielded metal arc cutting

Question 44

237. What polarity is wet welding?

Answer 44

Straight Polarity (electro negative)

Question 45

238. What do you put into cables connections when wet to get rid of water?What cable can you not put it in?

Answer 45

Electron, fiberoptic

Question 46

What is NSTM 091?

Answer 46

Sub Hull Inspect

Question 47

240. How are rope guards attached?

Answer 47

Welded or bolted

Question 48

241. During a shaft Lamination what is the ideal temperature? When do you contact the Nav sea?

Answer 48

73 degrees/ 60 degrees

Question 49

242. What degree do you cut MIP?

Answer 49

45 degree angle

Question 50

243. Safety of the ship definition?

Answer 50

Maintaining watertight integrity. Anything that can prevent the ship to recover from flooding

Question 51

248. What shaft taper? How long can it be exposed?

Answer 51

Shaft taper helps the installation and removal of the shaft. And helps keep the prop seated. Can be exposed 3 days

Question 52

249. How often does a cofferdam need a swim by?

Answer 52

Every 7 days

Question 53

250. How many gallons per min does a grinder push out.

Answer 53

9 gallons

Question 54

251. What are the 3 types of Non destructive testing and what do they do?

Answer 54

Ultrasonic- Measures Metal Thickness Ultravoilet- UV Light Residue Magnetic Particals- Shows Microcracks

Question 55

252. NSTM 245?

Answer 55

PROPS

Question 56

253. What is the position you take out the soft goods on a CPP blade changeout?

Answer 56

6 oclock

Question 57

254. What is the reference cell made out of?

Answer 57

Silver chloride/ anode-Platinum plated tantalum

Question 58

255. Difference between a Deficiency Log and Deficiency Report?

Answer 58

DL- Something that is in the scope of work that prohibits work DR- something reported wrong not in scope of work

Question 59

256. 3 different parts of a main on carrier? How MANY?

Answer 59

Main scoop, Circ, Discharge. 4 SETS

Question 60

257. Who are the 3 people you need sig from on carrier?

Answer 60

RDO, EDO, OOD

Question 61

258. Who are the 2 people you need sig from on sub?

Answer 61

EDO and SDO

Question 62

105. List ingredience for benski? How many rolls can you use per chapt. 16?

Answer 62

Rosin S25/W30 lb Cooking oil 5gal Cheesecloth 6x1 Bees wax 25lb Tallow 2/3lb Paraffin 2lb 1.5 rolls

Question 63

106. How long does it take rank up as an inspector?

Answer 63

Level1: 1 year Level2: 2 years Level3: 3 years

Question 64

79. What type of hydraulic fluid do you use to power tools?

Answer 64

P.R. HOUGHTON 1192

Question 65

80. Operating Temperature for Hydraulic tools?

Answer 65

80-120 degrees

Question 66

81. What is Max Temp?

Answer 66

140