Brainscape's Knowledge GenomeTM

Browse over 1 million classes created by top students, professors, publishers, and experts.


See full index

NATOPS > MAD/SAD/Comp > Flashcards

MAD/SAD/Comp Flashcards

0
Q

Function of the MAD Amplifier power supply.

A
  • Powers magnetic detector and detecting set control
  • Contains all BIT circuitry
  • Amplifies incoming MAD signals and sends them to the detecting set control
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
1
Q

What are the components of the ASQ-81 MAD system?

A
  1. Magnetic Detector
  2. Detecting Set Control
  3. Amplifier Power Supply
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

What is a unit 3 fail?

A

Magnetic Detector

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What is a unit 2 fail?

A

Amplifier Power Supply

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What is a unit 1 fail?

A

Detecting Set Control

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

What does a flashing system ready light on the detecting set control mean?

A

Equipment failure or high magnetic noise level.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

When does the system ready light on the detecting set control illuminate steady?

A

Within 5 minutes if all internal BITE checks are good.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

The altitude compensator switch on the detecting set control permits altitude changes in MAD maneuvers of_________

A

+/- 300 ft.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What two BIT flags are on the MAD Amplifier Power Supply?

A

DETECTOR

AMP PWR SUPPLY

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

What is on the front of the Amplifier Power Supply to aid in troubleshooting?

A

Built-in-Test switch and associated fail light.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What is the warm up time for ASQ-208 digital MAD?

A

3 minutes

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What is a unit 1 fault on ASQ-208?

A

Control/ indicator

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What is an added function of the digital MAD amplifier power supply?

A

Contains circuitry for all compensation functions.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Function of the Selector Control Subassembly?

A

Interfaces with DPS

Routes tone to SS3 ICS each time a SAD mark is generated

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Function of the Magnetic Variation Indicator?

A

Processes mad signal, separating unwanted noise signals from desired MAD anomalies.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What are the components of the ASA-65 Magnetic Compensator Group?

A
  • 9TC
  • MAD Maneuver Programmer
  • Mag Field Indicator
  • Amplifier Power Supply
  • Magnetometer
  • Coil Assembly
16
Q

Function of the Mag Field Computer?

A

Correlates inputs from magnetometer and MAD during maneuvers.
Calculated values are displayed on the mag field indicator.

17
Q

What are the paper speeds of the RO-32?

A

.75
3
12
Inches per minute

18
Q

When does the inhibit light on the MAD Selector Control illuminate?

A

3 or 4 seconds for all roll rates of 10° per second or greater

9 to 10 seconds when a valid MAD signal has been recognized

19
Q

What is the “WPN LOAD” dial on the CGA?

A

Compensates for number of Mk-46 Torpedos loaded on the aircraft.

20
Q

What is located on the side of the MAD Amplifier Power Supply?

A

Resonance Oscillator adjustment control.

NATOPS (30 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2024 Bold Learning Solutions. Terms and Conditions