ICE AND RAIN CONTROL SYSTEM Flashcards

1
Q

Prior to installation of a pneumatic surface-bonded type deicer boots, on the leading edge of the wing, you should

A

Remove all paint from the area to be covered by the deicer boot

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Which of the following are found in a laminated integral electrically heated windshield system?
1. Autotransformer.
2. Heat control relay.
3. Heat control toggle switch.
4. 24V dc power supply.
5. Indicating light.

A

1,2,3,5

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What is one check for proper operation of a pitot/static tube heater after replacement?

A

ammeter reading

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What controls the inflation sequence in a pneumatic deicer boot system?

A

distributor valve

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

What is the source of pressure for inflating deicer boots on reciprocating engine aircraft?

A

vane type pump

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Which of the following regulates the vacuum of the air pump to hold the deicing boots deflated when the pneumatic deicing system is off?

A

suction relief valve

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

What may be used to clean deicer boots?

A

soap and water

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Some aircraft are protected against airframe icing by heating the leading edges of the airfoils and intake ducts. When is this type of anti-ice system usually operated during flight?

A

whenever icing conditions are first encountered or expected to occur

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Which of the following indications occur during a normal operational check of a pneumatic deicer system?

A

fluctuating readings on the pressure gauge and relatively steady readings on the vacuum guage

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What method is usually employed to control the temperature of an anti-icing system using surface combustion heaters?

A

thermo cycling switches

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What is the purpose of the distributor valve in a deicing system utilizing deicer boots?

A

to sequence the deicer boots inflations symmetrically

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What is the purpose of the oil separator in the pneumatic deicing system?

A

to protect the deicer boots from oil deterioration

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Where are the heat sensors located on most aircraft with electrically heated windshields?

A

imbedded in the glass

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Two possible sources of heat for the operation of a wing thermal anti-icing system are

A

compressor bleed air and aircraft electrical system

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What maintains normal windshield temperature control in an electrically heated windshield system?

A

thermistors

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Arcing in an electrically heated windshield panel usually indicates a breakdown in the

A

conductive coating

17
Q

Which of the following connects vacuum to the deicer boots when the system is not in operation, to hold the boots tightly against the leading edges in flight?

A

distributor valve

18
Q

How do deicer boots help remove ice accumulations?

A

by breaking up ice formation

19
Q

Why are the tubes in deicer boots alternately inflated?

A

alternate inflation of deicer boot tubes keep disturbance of the airflow to a minimum

20
Q

Carburetor icing may be eliminated by which of the following methods?

A

alcohol spray and heated induction air

21
Q

Why should a chemical rain repellant not be used on a dry windshield?

A

it will restrict visibility

22
Q

What is the principle characteristic of a windshield pneumatic rain removal system?

A

an airblast forms a barrier that prevents raindrops from striking the windshield surface

23
Q

What mixture may be used as a deicing fluid to remove frost from an aircraft surface?

A

ethylene, glycol, and isopropyl alcohol

24
Q

Which of the following is the best means to use when removing wet snow from an aircraft?

A

a brush or a squeegee

25
Q

What are three methods of anti-icing aircraft windshields?
1. Blanket-type heating system.
2. An electric heating element in the windshield.
3. Heated air circulating system.
4. Hot water system.
5. Windshield wipers and anti-icing fluid.
6. Ribbon-type heating system.

A

2,3,5

26
Q

What icing condition may occur when there is no visible moisture present?

A

carburetor ice

27
Q

What should be used to melt the ice in a turbine engine if the compressor is immobile because of ice?

A

hot air

28
Q

What is used as a temperature-sensing element in an electrically heated windshield?

A

thermistor