General Knowledge

Question 1

Minimum fuel on board for towing

Answer 1

5000 lb

Question 2

Where can a list of approved tugs be found?

Answer 2

AOM 12.17.2

Question 3

Where is the location of the ELT’s?

Answer 3

Above the door inside the baggage compartment

Question 4

What two types of circuit breakers are used on the Global 6000

Answer 4

Thermal and virtual

Question 5

What is the minimum battery voltage to start the APU?

Answer 5

22V

Question 6

From which DC bus does each display unit receive its power

Answer 6

DU1 - DC Essential
DU2 - BATT Buss
DU3 - DC Bus 1
DU4 - DC Bus 2

Question 7

What is the minimum oil level to start the APU?

Answer 7

4.5 quarts.

Question 8

List the five things that occur during the fire test.

Answer 8

3 fire warning handles light
2 Master Warnings flash
9 CAS Messages appear
2 fire indication on N1
5 aural warnings sound

Question 9

When will the secondary nav lights come on

Answer 9

During power-up
to test.
Or
When the primary nav light becomes INOP.

Question 10

DC power carts should be limited to…

Answer 10

1500 amps

Question 11

If demand is too high, the APU will begin to meter _______ to meet that demand

Answer 11

Bleed air

Question 12

The APU can power how many ACMPs?

Answer 12

Only one at a time.

Question 13

If the APU is powering a bus above 37,000, what must also happen?

Answer 13

The associated ACMP must be powered off.

Question 14

What powers the EMER lights?

Answer 14

They are powered by their own battery packs that are charged by the DC ESS BUS.

Question 15

Fuel imbalance limits
(all)

Answer 15

Airborne = 1100 lb
Ground = 600 lb
Auto transfer starts at 400 lb

Question 16

Requirements for Aux tank fuel to be considered useful

Answer 16

500 lb in the AUX tank min
Wing tanks must be full
Flt planned above 30,000

Question 17

Requirements for AFT tank fuel to be considered usable

Answer 17

500 lb fuel in aft tank
5500 lb fuel in each wing tank
FL planned above 30,000’

Question 18

Will the auto throttles work when using N1 for power

Answer 18

No

Question 19

When operating the pacs in the manual mode, maintain output temps in what range

Answer 19

5°C to 60°C

Question 20

When is TOPI active

Answer 20

80 IAS - 400’ AGL

Question 21

When is LOPI active

Answer 21

200’ AGL to 50 its.

Question 22

Max difference between GNSS positions.

Answer 22

0.02 NM

Question 23

Minimum pressure setting for a huffer cart

Answer 23

40 psi

Question 24

How is an external DC card connected to the Aircraft electrical system?

Answer 24

The APU Start Contactor Assembly (ASCA) checks the DC parameters before connecting it to the APU BATT DIRECT BUSS

Question 25

When can the RAT gen be shut off line?

Answer 25

Once deployed it can only be removed if RAT handle is stowed and the RAT GEN switch is selected OFF.

Question 26

What is the minimum taxiway width needed to perform a 180° turn on a Global 6000 at max gross weight?

Answer 26

68'

Question 27

Minimum oil temperature to taxi

Answer 27

20°C

Question 28

When selecting an engine, bleed, switch to off, how many valves move?

Answer 28

Two The engine HP valve and the PRV.

Question 29

Minimum power for Wing anti-ice bleed

Answer 29

76% N2

Question 30

When do ADC probes heat up?

Answer 30

The perform a test when AC is first applied. They come on steady at engine start.

Question 31

Once triggered how long will an ICE CAS message be displayed

Answer 31

A minimum of 60 seconds provided no additional ice has accumulated

Question 32

When does the windshield hear enter the warm up mode

Answer 32

The first four minutes after selected on. Operates at 33% power Then normal mode.

Question 33

What is the nominal temp of the windshield in flight with the windshield gear selected on

Answer 33

37°C (98°F)

Question 34

With the loss of electrical power the cowl anti-ice valve fail...

Answer 34

Open

Question 35

With the loss of electrical power the wing anti-ice valve fail...

Answer 35

Closed