Brainscape's Knowledge GenomeTM


Top Flashcards (Certified)
All Flashcards

ET1 SWE - RPQ > ET2 RPQ > Flashcards

ET2 RPQ Flashcards

1
Q

What type of USCG units us the CASREP message to report degradation and operating limitations?

A

Non-modernized assets

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

A casualty is defined as an equipment malfunction or deficiency that cannot be corrected within how many hours?

A

48 Hours

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What are the requirements for drafting a CASREP?

A
  • Submit within 24 of a discovery of an equipment or system that cannot be repaired within 48 hours.
  • Report only a single instance of equipment failure per message
  • Maintain formatting rules for data sets and fields. UPPERCASE lettering and no special characters.
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

CASREPs transmitted with content or format errors; what actions can or cannot be taken?

A
  • Cannot be amended
  • Require the use of cancellation record messages to correct improper formatting or duplicate CASREP ID numbers
  • Require the use of an Update CASREP for all other corrections.
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

What CASREP casualty category does the Coast Guard not use?

A

CAT 1

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

What CASREP casualty category is a deficiency in mission essential equipment that causes a partial degradation in any primary mission, or a major degradation or complete loss of a secondary mission?

A

CAT 2

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

What CASREP casualty category is a major degradation in the current primary mission?

A

CAT 3

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What CASREP casualty category is a total loss of one current mission and unable to operate as directed by TACON and/or significant risk to cutter/crew survivability, which outweighs the gain in mission execution?

A

CAT 4

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

What CASREP type is used to identify the status of the casualty and the parts or assistance required?

A

Initial CASREP

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What CASREP type is used to provide new and more definitive information supporting the Initial CASREP?

A

Update CASREP – Minimally, update every 30 days or within 24 hours of status change.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What CASREP type is used to provide information when equipment is repaired and in operational condition?

A

Correct CASREP

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What CASREP type is used to cancel an Initial CASREP and all subsequent CASREP updates on a single equipment malfunction?

A

Cancel CASREP

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

CASREP heading format consists of four elements. What are they?

A
  • Precedence and date-time-group
  • Unit originating the message
  • Action addressee(s)
  • Information addressee(s)
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Precedence field indicates the importance of the message and the speed of service needed. What are the four categories?

A
  • Routine (R) – Speed of service is 6 hours or less.
  • Priority (P) – Speed of service is 3 hours or less
  • Immediate (O) – Speed of service is 30 minutes or less
  • Flash (Z) – Speed of service is less than 10 minutes
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What precedence do deployed units use for CAT 2, 3, and 4 CASREPS?

A
  • CAT 2 & 3 – (P)

- CAT 4 – (O)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

How many characters are there in the DTG on a CASREP.

A

12

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

CG Units without secure telegraphic capabilities will submit CASREPS with what classification?

A

Unclassified or FOUO

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

What CASREP classification is used when operating with the NAVY or as part of a joint task force for material deficiencies in equipment that reveal a degradation or inability of a unit to perform its operational missions?

A

Confidential Classification

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

What CASREP classification is used if material causalities degrade an overall fleet operational mission?

A

Secret Classification

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

The body of a CASREP can contain up to how many data sets?

A

20

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

From the Functional Area menu in FLS what option would you choose to create a MILSTRIP?

A

Procurement Option

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

What is a Priority 02 or 03 in a MILSTRIP?

A

Emergency Requisitions

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

What is a Priority 05 or 06 in a MILSTRIP?

A

Mission Impaired Requisitions

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
Q

What is a Priority 12 or 13 in a MILSTRIP?

A

Routine Requisitions

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
25
What is the "Free Issue" Code in a MILSTRIP?
00
26
There are two types of DLR items. What are they?
- DoD owned/managed items; identfied by their "7" series cognizant symbol. - Coast guard owned and managed reparable items
27
What is the proper MILSTRIP Advice Code to requisition DLR items?
5_ series
28
CG units shall document and package serviceable DLR items within how many hours?
48 hours
29
Coast Guard units will be charge what if a NRFI carcass is not returned to the appropriate repair or transshipment facilities?
Standard Price
30
Within how many days does a unit need to return the MTI part once replacement arrives?
-within 30 days
31
If a MTI is not returned in time on what day will the unit be billed?
75th day
32
what condition code are MTI's suppose to be when returned back to the AMM?
Condition F
33
True or False - All SPETERL and FSTER items shall have current calibration stickers affixed to the test equipment?
True
34
FSTER equipment shall have a label stating what?
FOR TROUBLESHOOTING ONLY
35
True or False - The ACR submitted will specify if FSTER equipment requires calibration.
True - A NO CALIBRATION REQUIRED sticker shall be affixed to the test equipment
36
What two categories of test equipment are stored together?
GPETE and SPETE
37
What test equipment shall be stored separately from GPETE AND SPETE?
FSTER and Non-Scat coded test equipment
38
How often should a shore unit test antennas and transmission lines?
Quarterly
39
How often should a floating unit test antennas and transmission lines?
Monthly
40
How often should a Submarine cable be tested?
Annually
41
How does a Megger work?
Sends high voltage which is sufficient in many cases to break down faults in the insulation, exposes any weak spots.
42
What form do you use to record your readings when using a Megger?
NAVSEA 9210/19 Resistance Test Record Card
43
When using a Megger to take readings when is maintenance required?
When the reading shows a resistance of 200 megaohms or less
44
You get a resistance of 5 megaohms or less when megging out an antenna. What do you do?
urgent need to correct the problem or replace
45
What length of RG-58 cable do you need to use the TDR?
6ft
46
What form is used to record your information when using a TDR?
NAVSEA 9210/19 Resistance Test Record Card
47
Identify this location (3-125-2)-4P-C
(3-125-2) - Fed from power distribution panel located on third deck, frame 125, port side 4P - 450 volt power cable C - third cable from the panel
48
Identify this cable R-ES4
R - Electronic cable ES - Surface search radar 4 - cable number *If a circuit has two or more cables with identical designations, a circuit differentiating number is placed before the R, such as 1R-ES4, 2R-ES4, and so on.
49
What two stuffing tubes are used in the Coast Guard?
Metal and Nylon stuffing tubes
50
When installing a stuffing tube what are the two requirements?
Airtight & Watertight Integrity
51
What are the 3 types of metal stuffing tubes?
Steel, Brass, and Aluminum
52
When replacing a rubber bushing what degree slit is cut?
30 degree
53
Down conductors bends shall be gradual and not have a radius less than how many inches? The angle of any bend shall not be less than how many degrees?
8 inches | 90 degrees
54
What is the average exposure time limit when working in a Upper Tier (Controlled Environment) for RF exposure?
6 minutes
55
What is the average exposure time limit when working in a Lower Tier (General Public) for RF exposure?
30 minutes
56
What is the width and color of a PEL boundary?
4 inches width and painted red
57
what are the required design specifications for RF RADHAZ warning signs? 4 answers
(a) Base material: Outdoor white vinyl, .004 inch thickness with permanent acrylic adhesive backing. (b) Shape: Diamond. (c) Colors: Red and yellow checked border on upper section of triangle; black lettering on lower section of triangle. (d) Sizes: 5” square size for normal shipboard use; 12” square size for shore installations, flight decks, DGPS, and CAMS/COMMSTA broadcast sites.
58
In steel frame buildings, make all structural members of the building electrically continuous by bonding each joint and interconnection with a welded, brazed, soldered, or high-compression bolted connection. Where direct bonds of these types are not possible, bridge the joint with what size wire able?
a l/0 AWG stranded copper cable both ends of which are brazed, welded, or bolted in place.
59
Equipment cabinets, electrical supporting structures, and utility pipes are to be connected to this structural steel or copper cable grid (equipotential plane) with what size wire?
#6 AWG copper wire.
60
Connect the bonded structural steel network to the earth electrode subsystem with what size copper cable?
1/0 AWG copper cables.
61
Lower Frequency Equipment - With all cables disconnected, measure the resistance between the signal ground terminal and the equipment case with an ohmmeter. The resistance should be greater than?
1M Ohm
62
Lower Frequency Equipment - Measure the resistance between the green safety wire and the case; the resistance reading should be?
0.1 ohm or less
63
Higher Frequency Equipment - Measure the resistance between the connector shell or body and its mounting surface. The resistance should not exceed?
0.001 ohm - one milliohm
64
Lightning Protection - The base insulator ball gap distance should be set approximately what length greater than the maximum arc-over distance under full operating transmitting power?
1/8 inch
65
Lightning Protection - To further discourage travel of lightning into the transmitter building, antenna feedlines should have what shaped bends rather than straight lead to the tower?
vertical Z
66
The basic earth electrode subsystem configuration shall consist of driven ground rods uniformly spaced around the facility and placed how far outside the drip line of structures?
2 to 6 feet
67
The resistance to earth of the earth electrode subsystem should not exceed how many ohms at fixed permanent facilities.
10 ohms
68
Ground rods shall be copper-clad steel, a minimum of how many feet in length? Spaced apart not more than twice the rod length, and shall not be less than 1.9cm (3/4 inch) in diameter.
3m (10 feet)
69
To assure adequate performance under all climatic conditions, resistance measurements of the earth electrode subsystem to earth will be made how often?.
3 month intervals for 12 months. After the 12 month period resistance measurements will be checked every 21 months.
70
Resistance from the workbench metal structure to the hull shall be less than or equal to?
0.1 ohms
71
A ground bus serving a row of workbenches shall be continuous cable not to exceed how many feet in length? The ground bus shall be insulated, stranded wire, size 2 AWG.
50 feet
72
Equipment grounding leads shall be provided for each __?__ feet of workbench installed. Grounding leads shall be insulated, stranded wire, size 10 AWG..
4 feet
73
What 3 aspects along the 11-year sunspot cycle determine what the best radio channel frequency will be for any two stations to communicate?
Time of Day, Time of Year, and position in time
74
What frequency spectrum does ALE HF fall between?
1.6 to 30 MHz
75
All members that will be participating in an ALE Network will have an assigned what, as a net member?
Alphanumeric ID
76
ALE Capabilities: The method used to select the best channel is based on?
Scanning
77
ALE Capabilities: What is the method used by ALE for testing the quality of channels and propagation paths under field conditions.
Sounding
78
1) “$” or “!” HEX 24 or HEX 21 2)
3) [“,”] 4) [“*"] Checksum field 5) Hex 0D 0A
1. Start of Sentence 2. TALKER identifier and sentence formatter 3. data fields 4. Checksum Field 5. End of sentence
79
SPS 50 X-band frequency?
9410 MHz + or - 30 MHz
80
SPS 50 S-Band frequency?
3050 MHz + or - 30 MHz
81
What two lights should be illuminated after start up completion on a PG-500?
STATUS & TRUE
82
Replace direction finder if output level is above what μv?
5uv
83
Replace DF antenna, if resistance remains < (?)MΩ after cleaning
10M Ohms
84
What are the six troubleshooting steps?
``` Symptom Recognition Symptom Elaboration Listing Probable Faulty Functions Localizing The Faulty Function Localizing Trouble To The Circuit Failure Analysis ```
85
ALE HF Spectrum is between what frequency?
1.6 to 30 MHz
86
Senior operational commander, immediate operational commander, and servicing product line manager are required ________ addresses on CASREPs
action
87
What solder alloy do we use for electronics?
63/37 tin/lead
88
When looking at a roxblock what are the numbers on the block?
measurements in milometers and decimals
89
A code plug zone consists of how many channels?
16
90
What are the four precedence categories in a CASREP and there speeds?
Routine - 6 hours Priority - 3 hours (O) Immediate - 30 minutes (Z) Flash - 10 minutes

ET1 SWE - RPQ (3 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2025 Bold Learning Solutions. Terms and Conditions