Electronic Fuel System Diagnosis Flashcards

1
Q

The two basic paths for diagnosis/troubleshooting are?

A

Symptom based

Fault code based

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Why must you never touch electronic components when vehicle is running?

A

There is a high voltage present that can cause serious electrical shock and personal injury

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What should be done before the removal of injectors?

A

Its advisable to disconnect the battery cables to power down the engine electronics and cranking system

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

When testing or replacing components in an electronic control system, you should:

A

Ensure the key switch is off before disconnecting any circuit

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

T/F ECM fault code charts will usually tell the technician to replace a component to see if that repairs the problem?

A

False

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Fuel should be drained out of the cylinder head fuel passages before removing injectors to prevent what?

A

Fuel draining into combustion chamber. this can hydraulically lock the engine and result in a bent connecting rod

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

If a special puller tool is not available, an EUI can be safely removed using?

A

A heel bar

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Before replacing an EUI, you should clean the injector tube paying particular attention to the?

A

Combustion seal seat

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Injector o-rings should be lubricated with what before installation?

A

Engine oil

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

When replacing an EUP, failure to purge the fuel supply passages will result in?

A

Engine oil dilution

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

T/F When replacing an EUP, it is an acceptable practice to remove both of the mounting bolts and let the spring tension eject the pump from the cylinder block?

A

False

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Before installing an EUP, you should?

A

Inspect the roller tappet for wear or damage

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

EUP heat shield are installed to?

A

Protect the electronic components

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Before beginning injector removal, it is advisable to:

A

Disconnect the battery cables to power down and engine electronics and cranking system

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

The battery cables should never be disconnected if?

A

The engine is running

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Most systems, normal sensor signals valves range from approximately _____ to _____ DC.

A

0.5 to 4.5 volts DC

17
Q

The thermistors used in temperature sensors have _______ resistance when cold and ________ resistance when hot?

A

high resistance cold

low resistance cold

18
Q

What is the data transfer rate of the j1587/J1708 protocols for multiplexing?

A

10 kbps

19
Q

What is the data transfer rate of theJ1939 protocols for multiplexing?

A

250 kbps

20
Q

The process of converting an analog signal to a digital signal is referred to as __________.

A

encoding

21
Q

There are two type of diagnostic trouble codes which are?

A

a flash code

a blink code