ECS Study Guide Flashcards
What are the 3 methods of emplacement?
Survey - within 10m from location
Provides UTM, Altitude, Azimuth
Modify survey - with in 10-40m from location
Provides UTM and Altitude
Map - within 40-120m from Location
Provides RS Location
TAB 96 allows crew members to enter 10 _____ and _____ Points to assist in mapping?
Bearing
And
Elevation
True or False Manually bypassing the PCF force class is done by hooking the general point and applying the identity through switch action. This method of identifying is recommended because it aids EDWA in determining the target classification.
False
True or false
The fault scenario will be automatically run on search mode and set to search mode 1 or search mode 3?
False
Who serves as the BDE link between the AADC and DCA operations, and land base ADA systems for engagement operations?
ADAFCO
Track Data shows you what?
Altitude of the track
And
Threat levels
What TABs do TAB 71 correlate with?
Weapons control
And
Identification areas
True or false
RS must locate missile in flight immediately after launch?
True
What entry on TAB 9 causes rapid clutter map update without reorienting the RS?
Zero degree slow
You can change the ballistic trajectory prediction values for a diving TBM.
Which page of what TAB can these values be adjusted?
TAB 1
Page 4
What is your distance for a RL 1 site?
1.3 to 10k
(VHF comms)
(45 degree LS Limit to PTL)
(60 degree RS Limit to PTL)
Mils elevation can not exceed?
140 mils
What are your left and right limits of ISLB?
5250
And
1150
What is your distance for A RL 3 site?
6 to 30k (VHF Comms) (LCS Controlled) (10 degrees RS Limit to PTL) (Minimum Of 2 PAC 3’s for an LS farm)
What is the AMG roll and cross roll?
5 degrees roll
and
10 degrees cross roll
What is the clearance angle for a local LS?
2 degrees
What is the clearance angle for a remote LS?
.5 degrees
What manual provides the firing battery personnel with information necessary to fault isolate the system based on the status monitor operations and operator observed faults in the firing battery system equipment?
TM 9-1425-1602-12-2
How many threat Launch Areas (TLA’s) can be inputted into TAB 56?
8
What switch indicator (S/I) works with TAB 55?
Alternate Sector 1
Alternate Sector 2
Drop short range
Drop long range
What are the four types of Initialization?
Short term
Long term
Standard
Standard with database read
How many units and points are in TAB 71?
55 units
And
250 points
How many pages are in TAB 72?
20 pages
True or false
TOD master syncs with the lowest battery?
True
And
Can be found in TAB 2 page 1
What is the difference between the KAA-63 table (TAB 73 and Compass rose table (TAB 74)?
KAA 63 uses time (24Hr)
And
Compass rose uses heading (24Hr)
What are the four major tasked of air defense function for ECS operation?
Friendly protect
Equipment control
Weapons control
Electronic counter counter measures (ECCM) Assist
What are some passive counter arm measures?
Emplaced on a hardened site
Cover and concealment
Use an external air picture
The authority assigning identify
Friend, Hostile, or Neutral
Is what?
Identification authority
IDA
When should you use short term Initialization?
For minor updates to the database
And
When accessing TAB’s that are not available in the tactical operates
True or false
When Syncing communication with other units, it is called synchronous?
False
It is called Asynchronous
What are the 3 levels of an arm alert warning?
General arm threat
Arm carrier alert
Arm attack
The nine most threatening targets to be engaged are listed in what TAB?
Engagement data
Describe the three types of weapons control statuses.
Hold - self defense or if directed by a higher E unit
Tight - stops auto engagement of a hostile track
Free - engage anything not positively identified as friendly
What type of operation involves conduct of the air battle by defeating enemy missile air crafts and missile attacks?
Engagement operations
The fault alert filter is enabled or disabled by pressing the ____ switch indicator (s/I) and when it’s enabled, the RS faults that are stable for over 3 minutes are reported.
Equipment control
What does RLRIU stand for?
Routing Logic Radio Interface Unit
Fix or fight categorizes significant faults into what categories?
Decision required
Fight now fix later
Must fix faults
What are the four Must Fix Faults?
System Hang or Crash
Map System Error
RS Isolate
Reorientation Nogo
How many trails can you have per man-station?
4
What are the 3 methods of control?
Autonomous
Decentralized
Independent
What are the 5 search modes in TAB 1 page 2?
ABT
ABT/TBM
ABT/CM
ABT/CM/TBM-self
TBM
What are the 8 Authorization in TAB 1?
ECM Pop up Minimum safe velocity Slow target engage Mode 4 friend SIF friend ARM classification Assumed friend
UTM world model (WGS 84) is used for what?
RS auto emplacement
In TAB 81, how long does it take for the GPS to find the location of the RS?
10 minutes
RHI consists of ____ horizontal beams in TAB 97
21
To prevent interference between fire unit RS’s, TAB ____ allows the operator to specify radio frequency signals to operate specific frequencies. This is also know as what?
TAB 54
And
Frequency diversity
The purpose of ____ is to point out terrain features that can mask and aircraft.
MTM (Masked Terrain Maps)
What is RL3 primary function?
TBM’s
What are the TCO responsibilities?
Friendly protect
ECCM assist
What are the engagement overrides?
Cease fire - stops farther engagements
Hold fire - self districts missile
Engagement hold - stops automatic engagements
What are the ID weight sets?
- Peace
- Transition
- War
And can be found in TAB 1 page 1
What is TAB 70?
Assets
What is TAB 71?
Volumes
Where can you fine the To be engaged queue?
TAB 78 Page 5
What are the TCA responsibilities?
Weapons control
Equipment control
What are the TADWs?
White - engagement not probable
Yellow - engagement probable
Red - engagement in progress
What are the sub categories of Fix or Fight?
Fix while fight
Must fix
Decision required
What is ULALT?
Urban Low Altitude Trajectory Control
Where can you find comm net status?
Fault data TAB S/l page 2
What does TIVS stand for?
Thermal
Integrated
Vented
System
What are the phases of RSOP?
Preparation
Movement
Survey
Emplacement