Domain V Deployment Flashcards

1
Q

Which of the following is performed to complete the Bill of Materials for a project?
a. Material take off
b. Material inspection
c. Material requisition
d. Material procurement

A

a. Material take off

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Which of the following typically shows all electrical and pneumatic devices and wiring and piping details specific to a control function?
a. Schematic diagram
b. Loop diagram
c. Termination diagram
d. Arrangement drawing

A

b. Loop diagram

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

For a rapid and representative measurement, how many pipe diameters downstream of the outlet of an inline neutralizer such as a static mixer should a pH electrode be installed?
a. 0.2
b. 2
c. 20
d. 200

A

c. 20

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Considering a 60Hz power source, at what speed does a 4-pole synchronous motor run?
(Hz x 60 x 2) / number of poles = no-load RPM.
a. 1200 RPM
b. 1800 RPM
c. 2400 RPM
d. 3600 RPM

A

b. 1800 RPM

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

When a large automation project makes significant changes to plant operations, it is BEST to perform operator training?
a. During the startup phase after water batching
b. After acceptance testing and prior to the startup phase
c. After the startup phase is complete and the process has stabilized
d. Six months prior to the startup phase, during control system development

A

b. After acceptance testing and prior to the startup phase

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

If the distance in a sheet line from the thickness gauge to the manipulated diebolt actuators is 200 meters and the line speed is 4 meters per second, what is the dead time (in seconds) due to transportation delay?
a. 0.02
b. 5
c. 50
d. 200

A

c. 50

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

If an exothermic reactor can run away in manual, which method should be used to tune the reactor temperature controller?
a. Lambda tuning method
b. Ziegler-Nichols tuning method
c. Open-Loop, shortcut tuning method
d. General-purpose, closed-loop tuning method

A

d. General-purpose, closed-loop tuning method

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

An increase in which controller setting can compensate for a thermowell lag?
a. Rate
b. Gain
c. Reset
d. Filter time

A

a. Rate

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Increasing the safety integrity level of a system is directly related to which of the following parameter changes?
a. Increasing the MTBE
b. Increasing the MTTR
c. Increasing the PFD
d. Increasing the RRF

A

d. Increasing the RRF

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What type of failure prevents a safety instrumented function from performing its automatic protection function?
a. Fail-safe
b. Fail-danger
c. No effect failure
d. Annunciation failure

A

b. Fail-danger

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What instrument is used to verify a fiber optic splice location, integrity, and power loss in a long length of installed fiber optic cabling?
a. Optical Amplifier
b. Optical spectrum analyzer
c. Optical time domain reflectometer
d. Optical power meter/ light source

A

c. Optical time domain reflectometer

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Which of the following documents includes testing of a unit startup and shutdown procedures?
a. Software module test specifications
b. Software integration specifications
c. System Acceptance Specifications
d. Network Acceptance specifications

A

c. System Acceptance Specifications

How well did you know this?
1
Not at all
2
3
4
5
Perfectly