DIKTA Ch7 Flashcards
Switch SW1 connects its G1/0/1 port to PC1. Both devices use IEEE autonegotiation and have 10/100/1000 ports. Which answer describes how the switch chooses its G1/0/1 speed and duplex settings? (Choose two answers.)
a. Speed by comparing capabilities per received autonegotiation messages
b. Speed by analyzing the electrical signal of incoming Ethernet frames from PC1
c. Duplex by comparing capabilities per received autonegotiation messages
d. Duplex by analyzing the electrical signal of incoming Ethernet frames from PC1
e. Duplex by choosing a default based on the chosen speed
a. Speed by comparing capabilities per received autonegotiation messages
c. Duplex by comparing capabilities per received autonegotiation messages
In which of the following modes of the CLI could you configure the duplex setting for interface Fast Ethernet 0/5?
a. User mode
b. Enable mode
c. Global configuration mode
d. VLAN mode
e. Interface configuration mode
e. Interface configuration mode
Switch SW1 connects its G1/0/1 port to PC1. Both devices are 10/100/1000 ports. While the switch port uses IEEE autonegotiation, PC1 has disabled it. Which answer describes how the switch chooses its G1/0/1 speed and duplex settings?
a. Speed by comparing capabilities per received autonegotiation messages
b. Speed by analyzing the electrical signal of incoming Ethernet frames from PC1
c. Duplex by comparing capabilities per received autonegotiation messages
d. Duplex by analyzing the electrical signal of incoming Ethernet frames from PC1
e. Duplex by choosing a default based on the chosen speed
b. Speed by analyzing the electrical signal of incoming Ethernet frames from PC1
e. Duplex by choosing a default based on the chosen speed
Switch interface G1/0/5 has been cabled correctly in anticipation of some weekend work. However, the engineer needs to prevent the interface from being used until she enables it remotely during a change window this weekend. Which action helps achieve that goal?
a. Unplug the cable.
b. Issue the shutdown g1/0/5 global configuration command.
c. Issue the shutdown interface subcommand under interface g1/0/5.
d. Issue the disable g1/0/5 global configuration command.
e. Issue the enable interface subcommand under interface g1/0/5.
c. Issue the shutdown interface subcommand under interface g1/0/5.
An engineer configures Cisco switch SW1 with the commands interface range G1/0/10-20 and then description connected to endpoint device. The engineer exits configuration mode and issues a show running-config command. Which answers best describe the related output? (Choose two answers.)
a. The output includes the interface range command.
b. The output does not include the interface range command.
c. The output lists one description connected to endpoint device interface subcommand.
d. The output lists 11 description connected to endpoint device interface subcommands.
b. The output does not include the interface range command.
d. The output lists 11 description connected to endpoint device interface subcommands.
The output from the switch command show interfaces status shows interface Fa0/1 in a “disabled” state. Which of the following is true about interface Fa0/1? (Choose three answers.)
a. The interface is configured with the shutdown command.
b. The show interfaces fa0/1 command will list the interface with two status codes of administratively down and line protocol down.
c. The show interfaces fa0/1 command will list the interface with two status codes up and down.
d. The interface cannot currently be used to forward frames.
e. The interface can currently be used to forward frames.
a. The interface is configured with the shutdown command.
b. The show interfaces fa0/1 command will list the interface with two status codes of administratively down and line protocol down.
d. The interface cannot currently be used to forward frames.
Switch SW1 Gigabit 1/0/1 connects to switch SW2’s Gigabit 1/0/2 interface, both 10/100/1000 ports. The switch SW2 configuration includes the speed and duplex commands, the combination of which happens to disable autonegotiation on that port. Which combination of settings in SW2’s speed and duplex commands results in a duplex mismatch between SW1 and SW2? (Choose two answers.)
a. speed 100 and duplex full
b. speed 100 and duplex half
c. speed 10 and duplex full
d. speed 10 and duplex half
a. speed 100 and duplex full
c. speed 10 and duplex full
Switch SW1 connects via a cable to switch SW2’s G1/0/1 port. Which of the following conditions is the most likely to cause SW1’s late collision counter to continue to increment?
a. SW2’s G1/0/1 has been configured with a shutdown interface subcommand.
b. The two switches have been configured with different values on the speed interface subcommand.
c. A duplex mismatch exists with SW1 set to full duplex.
d. A duplex mismatch exists with SW1 set to half duplex.
d. A duplex mismatch exists with SW1 set to half duplex.
