Data Sheet V Flashcards

1
Q

Flanges - Thread engagement acceptance criteria

A

-1 (570:5.12/31.3:335.2.3)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

The ratio of Endurance Limit Stress to Ultimate Tensile Stress for Carbon Steel

A

0.4-0.5 (571:4.2.16.3.b.ii)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Testing - Minimum range of pressure gauge used during a pressure test (multiplied by test pressure)

A

1.5 (Section V:T-1031.a)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Testing - the Preferred range of pressure gauge used during a pressure test (multiplied by test pressure)

A

2 (Section V:T-1031.a

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

NDE - Number of additional welds or joints to examine when a weld defect is found during random examination

A

2 (31.3:341.3.4.a

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

PWHT - minimum number if thermocouples required when performing a local PWHT instead of a 360-degree band

A

2 (570: 8.2.3.3.d)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Weld Qualification - Number of tension test to qualify a WPS

A

2 (Section IX:QW451.1)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Weld Qualification - Number of bend test to qualify a welder or welding operator in welding positions 1G - 4G

A

2 (Section IX:QW452.1.a)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

NDE - Minimum number if exposers to RT 360 degrees of a weld using a double-wall technique, double-wall view

A

2 (Section V:T-271.2.b.1)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

NDE - RT film density range - allowed for the weld and IQI when using a gamma ray source

A

2.0 - 4.0 (Section V:T-282.1)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

NDE - Minimum number of exposures to RT 360 degrees of a weld using a double-wall technique, single wall view

A

3 (Section V:T-271.2.a)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Impact test - Number of test bars in each set

A

3 (31.3:323.3.3)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

NDE - when using a shim under a hole-type IQI, the number of sides of the IQI that must be seen in the RT image

A

3 (Section V:T-277.3)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Testing - Maximum range of pressure gauge used in a pressure test (multiplied be test pressure)

A

4 (Section V:T-1031.a)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Weld Qualification - Number of bend test to qualify a WPS

A

4 (Section IX:QW451.1)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Weld Qualification - number of bend test to qualify a welder or welding operator in the welding positions 5G and 6G

A

4 (Section IX:QW452.1.a Note 1)

17
Q

Design - number of stress cycles needed to become rated as Severe Cyclic Service

A

7000 (31.3:300.2)