Chapter 2 Flashcards
What is the max vehicle weight of the A/S32A-32 Spotting dolly?
11,500 lbs
What is the A/S32A-32?
SD-2 Spotting dolly
What is the draw bar pull of the
A/S32A-32 Spotting dolly?
14,000 lbs
What is the max lifting capacity of the A/S32A-32 spotting dolly?
16,000 lbs
What is the max speed of the A/S32A-32 spotting dolly?
Loaded 2mph
Unloaded 5 mph
What is the ground clearance and turning radius of the A/S32A-32 spotting dolly?
Ground clearance: 5 inches
Turning radius: 0 inches
What is the A/S32A-31A?
Tow tractor
The A/S32A-31A has a break warning light that will illuminate when the pressure falls below?
1350 psi
What is the tire pressure for the A/S32A-31A?
Front: 70 psi
Rear: 60psi
What gear should the A/S32A-31A tow tractor be in while tow an air craft?
1st or Reverse
What is the gross vehicle weight of the A/S32A-31A tow tractor?
12,400 lbs
What is the draw bar pull of the A/S32A-31A?
8,500 lbs
The engine/transmission warning light on the A/S32A-31A will illuminate when?
- The torque converter reaches temperatures above 300 F
- Engine Temperature goes above 215 F
- Engine oil pressure falls below 6 psi
All tow tractor operators must be licensed in accordance with?
OPNAVINST 4790.2
The Areo high power tie down has a working load of?
30,000 lbs
What is the working load for the MXU-657?
45,000 lbs
Before using any non skid compound, you should consult which chapter of the naval Ship’s tech manuel (NSTM), NAVSEA S9086-VG-STM-010, concerning deck coverings?
634
Nonskid materials in the federal supply system are assigned a non-extendable shelf life of how many months?
12
At what range, in degrees Fahrenheit, should nonskid coatings be stored until used?
55 to 100
Name some precautions you must follow prior to deck preparation and nonskid application.
- Drop clothes and masking must be use to prevent damage from abrasive materials
- Deck opening must be covered with strips of sponge rubber, adhesive plates/circles or similar material
- One tie crossbar near the refueling area should be cleaned to bare metal and masked prior to nonskid application
What causes the majority of nonskid failure?
Improper application or application over a poorly prepared deck
Composition G nonskid is used in the arresting gear wire run out areas. True or False?
False, composition L is used
Which composition of nonskid should be used on the flight deck and hanger deck areas( except beneath the arresting cables and run out areas)
Type 1 or 2, composition G
What is a sign that nonskid should be resurfaced?
Patches of the nonskid surface are easily removed by chipping or scrapping
What is the best method to applying nonskid to heavy wear areas, such as flight decks?
Rolling or troweling
What is the general cure time range of surface primer?
6 to 12 hours
What should you do before using the solvent degreasing method to prepare a steel deck for priming?
Make sure the deck surface is absolutely clean
What is the only authorized nonskid coating to be used in carrier landing and arresting gear cable run out areas?
Type 1 or 2, composition L
Nonskid epoxy primers may be applied by what methods?
Brushing, roller coating or spraying
What equipment must you perform preventive maintenance on?
Tie-down and chains
Tractors
Chocks and tow bars
What determines the maneuverability and ease of handling a tractor?
Dimensions, turning radius and transmission
What factor determines the amount of force a tractor can exert?
The type and condition of the surface on which it is being used