Chapter 11 - Online Quiz Flashcards

1
Q

In slip critical connections, the bolts grip the two steel components so tightly together that the load is transferred between them by friction.

A

True

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Which of the following is primarily responsible for preparing structural steel shop drawings, which show details of connections, exact spacing of bolt holes, anchor bolt sizes and locations, etc and for the site steel components that are ready to be assembles without further processing?

A

steel fabricator

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

The width of the flange of a W12x14:

A

must be looked up in a handbook

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Open web steel joints are made by cutting the web of a wide flange section along a zigzag path, then rejoining the two halves in a greater depth by welding. T/F

A

False

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Plumbing up refers to the process of rasising sections of steel from the ground to their position in the building. T/F

A

False

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Shear studs are often welded to the top of a steel beam. These studs serve to:

A

bond the beam to the concrete and cause them to act as a single unit

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Which of the following’s principal function is to provide lateral stability to a steel frame?

A

all of the above (shear connections, diagonal bracing, anchor bolts, high-strength bolts)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Riveting of steel building frames is obsolete. T/F

A

True

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Tensile structures made of steel cables can be made rigid against wind uplift. T/F

A

True

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Plate girders are available from stock in a variety of sizes and spans. T/F

A

False

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

The one distinguishing characteristic of a welded moment connection is:

A

the beam flanges are attached with full-depth welds

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Open-webbed steel joists are usually used in a commercial steel-framed building to support

A

roof decks

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Most steel beams are I beam shapes. T/F

A

False

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Rigid frames are economical for low cost manufactures steel buildings. T/F

A

True

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Which of the following terms is not associated with achieving longer spans in steel?

A

backup bar

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Standard steel structural shapes are produced by:

A

rolling

17
Q

Shear panels or shear walls are sometimes used in steel-framed buildings. Which component of wood light-frame construction serves the same function as a shear panel/wall?

A

wall sheathing

18
Q

On a drawing, a building element is referred to as W10x33. This element could be a

A

beam

19
Q

Column baseplates for small columns are usually attached to the columns in the fabricators shop. T/F

A

True

20
Q

Which of the following is not an acceptable means of making a steel column fire-resistant?

A

all are acceptable (wrap with drywall, apply paint, encase in concrete, use water-filled column)

21
Q

The following materials are suitable for fireproofing steel columns:

A

all of the above

22
Q

You would be most likely to find leveling nuts near which item?

A

column base plate

23
Q

A member on a steel drawing is identified as L 5x4 x 3/8. This member is:

A

an angle