Book 1: Unit 5 - Piping And Valves REVIEW Flashcards

1
Q

The threads are cut by using a pipe die or die head, which is held in a frame called a:

Select one:

A. Threader
B. Stock
C. Collet
D. Reamer
E. Ratchet

A

B. Stock

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Gate valves are suitable as _____ valves.

Select one:

A. Stop (or isolating)
B. Throttling
C. Remote controlled
D. Control
E. Diverting

A

A. Stop (or isolating)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

The air present in steam lines and equipment must also be removed to prevent:

Select one:

A. Corrosion from oxygen
B. Rusting from carbon dioxide
C. Pitting from carbon dioxide
D. Caustic embrittlement
E. Corrosion from carbon dioxide

A

E. Corrosion from carbon dioxide

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Valve stem leaks can normally be fixed by:

Select one:

A. Tightening the hand wheel nut
B. Slightly backing off the hand wheel
C. Slightly tightening the packing nut or gland
D. Tightening the hand wheel down
E. Tightening the bonnet connection

A

C. Slightly tightening the packing nut or gland

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

One of the general designs of gaskets is the ______ gasket.

Select one:

A. Hard
B. Fat
C. Round
D. Soft
E. Ring joint

A

E. Ring joint

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

The valve stem connects the:

Select one:

A. Yoke to the wheel
B. Disc to the yoke
C. Bonnet to the body
D. Wheel to the disc
E. Wheel to the bonnet

A

D. Wheel to the disc

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Joining or connecting lengths of piping by the use of threaded pipe and screwed connections is generally used for pipe sizes _____ and smaller for low and moderate pressures.

Select one:

A. 1/2 in
B. 2 in
C. 3/4 in
D. 1 in
E. 3 in

A

B. 2 in

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

The service temperature of Reflective Metal Insulation is above:

Select one:

A. 1000°C (1832°F)
B. 2250°C (4082°F)
C. 1650°C (3000°F)
D. 1040°C (1904°F)
E. 1200°C (2192°F)

A

D. 1040°C (1904°F)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Joining or connecting lengths of piping by the use of threaded pipe and screwed connections has the advantage of:

Select one:

A. Gaskets are not required
B. The piping can be easily assembled or disassembled
C. The strength of the pipe is not reduced
D. There is no chance of leakage
E. A qualified welder must be used

A

B. The piping can be easily assembled or disassembled

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Before installing a trap blow new lines clear of all:

Select one:

A. Carbon dioxide
B. Condensate
C. Air
D. Foreign matter
E. Steam

A

D. Foreign matter

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Ideally with a hot water heating installation the minimum pressure of _____ should be maintained on the highest heating unit in the building.

Select one:

A. 28 kPa (4 psi)
B. 20 kPa (2.9 psi)
C. 50 kPa (7.3 psi)
D. 100 kPa (14.5 psi)
E. 10 kPa (1.5 psi)

A

A. 28 kPa (4 psi)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

All valves must be properly identified with one of the markings indicating the:

Select one:

A. Manufacturers name or trademark
B. Mass of the valve
C. Type of packing used
D. Size of the valve
E. Type of valve

A

A. Manufacturers name or trademark

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

The purpose of the stream trap is to discharge ______ from steam lines and equipment without permitting steam to escape.

Select one:

A. Air and steam
B. Water and air
C. Condensate and air
D. Steam and condensate
E. Water and condensate

A

E. Water and condensate

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

The slip expansion joint requires _____ then the expansion bend.

Select one:

A. Higher pressures
B. Higher temperatures
C. Less space
D. More space
E. Lower temperatures

A

C. Less space

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

One of the different general classes of traps according to their principle of operation is the ______ trap.

Select one:

A. Thermodynamic
B. Pneumatic
C. Electronic
D. Electrical
E. Hydraulic

A

A. Thermodynamic

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

No lubricant is used on the _____ because any excess lubricant is forced into the piping system.

Select one:

A. Outside of the fitting
B. Female fitting threads
C. Inside of the pipe
D. Both male pipe and female fitting threads
E. Male pipe threads

A

B. Female fitting threads

17
Q

The service temperature limit of refractory fiber insulation is:

Select one:

A. 1200°C (2192°F)
B. 2250°C (4082°F)
C. 1650°C (3000°F)
D. 1038°C (1900°F)
E. 1000°C (1832°F)

A

C. 1650°C (3000°F)

18
Q

Joining or connecting lengths of piping by the use of threaded pipe and screwed connections has the disadvantage of:

Select one:

A. The piping can not be easily assembled or disassembled
B. There is no chance of leakage
C. The strength of the pipe is reduced
D. A qualified welder must be used
E. Gaskets are not required

A

C. The strength of the pipe is reduced

19
Q

In the design of a mechanical trap a a/an ______ is used to open and close the trap outlet valve.

Select one:

A. Bellows
B. Temperature difference
C. Pressure difference
D. Bi-Metallic strip
E. Inverted bucket

A

E. Inverted bucket

20
Q

Threaded ______ pipe fittings cannot be used for gas service piping systems.

Select one:

A. Cast Iron
B. Steel
C. Malleable iron
D. Aluminum
E. Copper

A

A. Cast iron