Auto

Question 1

The component of a water cooled engine that dissipates heat is the?

Answer 1

Radiator

Question 2

A carburetor has the same function As a?

Answer 2

Fuel injection system

Question 3

An engines rotational energy is stored by using which mechanical device

Answer 3

Flywheel

Question 4

A Catalytic converter?

Answer 4

Creates chemical reaction

Question 5

Which of the following is not normally part of a routine automotive tuneup?
A. Replace the air filter.
B. Replace the spark plugs
C. Replace the CV axles.
D. Check the fluids.

Answer 5

C. Replace the CV axles.

Question 6

Antifreeze is used to?
A. Prevent the engine from overheating
B. Prevent water in the cooling system from freezing.
C. Prevent damage to the engine block.
D. All of the above.

Answer 6

D.. All of the above.

Question 7

Why might you be hesitant to offer a jumpstart to another vehicle?

Answer 7

One of the vehicles has a digital ignition system

Question 8

What is most likely to occur a spark plugs gap is too wide?

Answer 8

It could misfire

Question 9

What is the primary purpose of an intake manifold?

Answer 9

To distribute the air – fuel mixture

Question 10

What engine component keeps running power to a vehicles electronics when the engine is running?

Answer 10

Alternator

Question 11

This system that controls how much power goes to a vehicle’s wheels is it?

Answer 11

Transmission

Question 12

A catalytic converter reduces?

Answer 12

Toxic emissions

Question 13

What part of the vehicle supports its weight?

Answer 13

Struts

Question 14

Overheating the engine can cause all of the following problems except?
A. Burning engine bearings.
B. Enlarge pistons.
C. Melted engine parts.
D. Improved fuel efficiency.

Answer 14

D. improve fuel efficiency

Question 15

The device that converts in automobiles, mechanical energy to electrical energy is called the?

Answer 15

Alternator

Question 15

A primary advantage of the electronic ignition system over conventional ignition system is that?

Answer 15

The electronic ignition system requires a lower voltage to provide a higher voltage for spark

Question 16

The primary purpose of a piston rings is too?

Answer 16

Seal the combustion chamber and allow the pistons to move freely

Question 17

The crankshaft typically connects to a?

Answer 17

Flywheel

Question 18

What component allows the left and right wheels to turn at different speeds when cornering?

Answer 18

Differential

Question 19

If a car is ignition system, lights, and radio don’t work, the part that’s probably manufactured is The?

Answer 19

Battery

Question 20

A good tool to cut electrical shapes in wood would be a?

Answer 20

Coping saw

Question 21

A two strike engine will normally be found on?

Answer 21

Snowmobiles, chainsaws, and some motorcycles

Question 22

A belt sander would best be used to?

Answer 22

Finish wood

Question 23

Big block engines generally have?

Answer 23

More than 5.9 L of displacement

Question 24

A car equipped with limited slip differential?

Answer 24

Transfers, the most driving force to the wheel with the greatest amount of traction

Question 25

A good tool for spreading shaping mortar would be a

Answer 25

Trowel

Question 26

Plump bobs are used to?

Answer 26

Check vertical references

Question 27

Rebar Is used to?

Answer 27

Reinforce concrete

Question 28

Annual ring, clout, and spring head are types of?

Answer 28

Nails

Question 29

A ripsaw cuts?

Answer 29

With the grain of the wood

Question 30

A Cam belt is also known as?

Answer 30

Timing belt

Question 31

To check for horizontal tunes, the best tool to use is a?

Answer 31

Level

Question 32

A bucking Bar is used to?

Answer 32

Form rivet bucktails

Question 33

A two – penny nail is? A. Thicker Then a 10d Nail B. Shorter than a 10 d Nail C. The same thing as a 10d Nail D.Harder Than a 10d nail

Answer 33

B. Shorter than a 10d nail

Question 34

A hacksaw is used to cut?

Answer 34

Metal

Question 35

To drive a cold chisel, the best object to use would be?

Answer 35

A hammer

Question 36

The best tool for cutting curves or shapes in wood is a?

Answer 36

Coping saw

Question 37

What is the next step after filling in a hole with plastic filler and letting it dry?

Answer 37

In the area was medium grain sandpaper

Question 38

Why is a cross shaft Lug wrench better than a single shaft wrench

Answer 38

It gives more leverage

Question 39

What is the strongest way to permanently join Two pieces of metal

Answer 39

Welding

Question 40

Without a key, what tool would you use to remove a padlock from a gate?

Answer 40

Bolt cutters