Anti-Friction Bearings Flashcards

1
Q

To check the concentricity of a bearing housing bore, check the diameter with a ______ gauge in at least 3 locations.

A

Telescoping

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

You can inspect a shaft for straightness by placing it in a lathe and checking for concentricity with a ______ indicator.

A

Dial

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

If the inside of a bearing is discolored, it is likely due to ______.

A

Overheating

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

If the bearing raceway has tracks that appear as axial lines that have the same spacing as the rolling elements, then the likely cause is _______ acring.

A

Electrical

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Hot mounting a bearing is most practical for bore sizes over _____ mm.

A

20

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Hot mounting a bearing usually involves heating a bearing to ______ degrees C.

A

80

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Never heat a bearing above ________ degrees C.

A

120

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Bearing _______ clearance is the total amount of clearance between the rolling elements and the raceway.

A

Internal

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

_____ clearance is the internal clearance (Radial or axial) before the bearing is mounted

A

Initial

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

_________ clearance is the internal clearance (radial or axial) after the bearing is mounted.

A

Residual

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

_________ clearance is the internal clearance (radial or axial) in a bearing when it is running at its operating temperature.

A

Running

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

When bearing internal cleance is measured by placing a dial indicator on the outer ring and moving it while holding the inner ring, it is called a _______ check.

A

lift

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

_______ is the load that the rolling elements are under before any external load is applied.

A

Preload

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

The surface on which the rolling members roll is called the ______.

A

Raceway

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

The _______ or separator prevents the rolling elements from rubbing against each other.

A

Cage

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

The cage or separator push the rolling elements through the ______ zone.

A

Unloaded

17
Q

Review parts of anti-friction bearing page 3.

A

Page 3

18
Q

Under load, a ball bearing shape changes from spherical to ______.

A

Elliptical

19
Q

If the load on a bearing is at 90 degrees to the shaft centre line, it is called a ______ load.

A

Radial

20
Q

If the load on a bearing is parallel to the shaft centre line, it is called an _______ load.

A

Axial

21
Q

A _____ load on a bearing is both radial and axial.

A

Combination

22
Q

A _____ load bearing had 100% loading on all rolling elements at the same time.

A

Thrust

23
Q

A higher radial load bearing ______. A high radial load bearing _____.

A

Maximum capacity deep groove ball bearing, Deep groove ball bearing.

24
Q

A self-aligning bearing have a _____ seat on the outside of the outer ring.

A

Spherical

25
Q

Match types of loads to each type of bearing.

A

See pic

26
Q

Know each bearing series #. Page 33

A

Page 33

27
Q

A 6210 bearing had a bore diameter of _____ mm.

A

50

28
Q

A bearing with a tapered bore is indicated with the letter _____.

A

K Pg. 34

29
Q

ToF. A C3 bearing had more internal clearance than a C4 bearing.

A

False. C1 Tightest, C5 most clearance Pg. 34

30
Q

Non-rubbing seals are often called _____.

A

Shields pg. 70

31
Q

Rubbing or non-rubbing seal? Sheet metal attached to the outer ring _____.

A

Non-rubbing Pg. 70

32
Q

Rubbing or non-rubbing seal? Sheet metal attached to the outer ring with a synthetic rubbing lip seal contacting the shaft _______.

A

Rubbing seal pg. 70