AIT Readiness Flashcards

0
Q

The welder trade in Alberta consists of how many periods of technical training?

A

Currently the apprentice must cover three terms of eight weeks or 240 hours 3x.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
1
Q

What does it mean when a trade is called a compulsory trade?

A

You must be a registered apprentice or a journeyman to work in the trade.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

In order to become an apprentice in Alberta you must enter into a ____________ agreement with your employer.

A

Contractual.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Who is responsible to ensure the apprenticeship record book is kept up-to-date?

A

The apprentice.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

A cover letter should accompany your resume when applying for a job. The purpose of the cover letter is to:

A

Show why you are a good fit for the job and showcase yourself.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

According to the Occupational Health & Safety act of Alberta a rolling scaffold with a minimum base dimension of 3 feet must not exceed ___ feet in height.

A

Three times the minimum base, so 9 feet.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

According to the Occupational Health & Safety act of Alberta an employer must ensure that hot work is not performed:

A

On combustible tanks or areas that are not properly steamed or cleaned.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

According to the Occupational Health & Safety act of Alberta employer must ensure that acetylene tanks are secured:

A

In an upright or vertical position.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Safety screen must be used to protect other workers from ______ & _______ when you were welding.

A

Arc rays and sparks.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

According to the Occupational Health & Safety act of Alberta the __________ ensures that the worksite is kept clean.

A

Employer.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

In compliance with WHMIS, material safety data sheets must be reviewed and updated every ___ years.

A

Three years.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

According to the WHMIS system, material safety data sheets must be kept:

A

The general public and readily available.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Your boss has requested that you perform a weld on a gas tank that is still half-full. You should:

A

Refuse the job. You as a worker have the right to refuse unsafe work.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Before entering the vessel to perform a weld, it is critical that a welder always checks the vessel for:

A

Oxygen levels and explosive levels.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

The container that has contain flammable materials must be properly cleaned before you can weld it.

To properly clean the container, you can:

A

Steam out the container, or use a caustic bath or an inert gas, then sniff for explosive levels.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

The proper order for placement of lens on the front of the welding helmet starting from the outside and working inward is:

A

1) clear plastic or glass lens
2) gasket
3) filter plate
4) clear plastic or glass
5) plastic only in the helmet

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

____________ type of clothing is considered safe for a welder to wear when welding.

A

Nylon, polyester, or rayon.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

On a welding helmet, shade number ___ is recommended for medium to high amperage SMAW.

A

12.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

__________ rays could cause burning of the eyeballs.

A

Ultraviolet.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

Exposure to _________ rays when inspecting welds could cause cancer or damage to body tissues.

A

Gamma rays or x-rays.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

Exposure to these rays when welding could cause retina damage.

A

Infrared rays.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

A welder working for eight hours in a shop where the noise level is over ____ decibels must wear hearing protection.

A

85 dB.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

Gloves made of ______ should be used for welding.

A

Leather.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

Which metal can be a carcinogen when inhaled as a fume?

A

Cadmium.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
What risk increases the welder is welding with wet gloves?
Electrical shock.
25
The ventilation system in a welding shop should have the air completely changed at least __ times every hour.
Four.
26
The main reason for using a wraparound device is to:
Mark a straight line around pipe.
27
Welding pliers have a multifunction design that is specifically applicable to use when completing:
GMAW, FCAW, or SAW processes.
28
The length of the file is determined by measuring from:
Heel to the point of the file.
29
If you wanted a smooth finish, you would use what kind of file?
A single cut file.
30
What kind of wrench is sized the same on both ends?
A combination wrench.
31
When using an adjustable wrench, the wrench must be positioned so force acts:
Against the solid jaw.
32
The peen of a hammer is used:
For removing stress created by welding or riveting work.
33
Bench grinder should have wheel guards that cover at least how much of the wheel?
66.6% or 2/3 of the disc.
34
The tool rest on a bench grinder should be adjusted so that there is no more than ___ millimeters between the grinding wheel and the rest.
3 mm or 1/8 of an inch.
35
The term "dressing" when referring to a grinder wheel means that you are:
Reshaping the stone trueness, also for removing the glaze to recover sharpness.
36
Using the portable grinder to perform a circus grind you should hold the disc out of flat angle of approximately how many degrees to the surface you were grinding?
Approximately 10°.
37
The term "grit" refers to grinding wheels:
Abrasiveness; how much grit per square inch.
38
A portable hand drill will be rated according to the size of its:
Chuck.
39
The main parts of a drillbit are the:
Shank, body and point.
40
The drill point angle of the twist bit is manufactured at how many degrees?
118°.
41
An example of a dimensional weld fault is:
Warping.
42
Weld faults are grouped into three general classes; they are:
Defective properties, dimensional and structural.
43
The term "notching effect"can be described as:
Any change in the cross-section of the material.
44
The term convex city used when referring to a weld normally refers to:
A bulging profile.
45
Excessive concavity is a condition that is often associated with:
Fillet welds.
46
An oxyfuel outfit must have hoses that are made of:
Cotton, neoprene or rubber.
47
Oil and grease must be kept away from oxygen because it:
Can become explosive.
48
If acetylene gas is to be stored at high-pressure it is dissolved in:
Acetone.
49
Regulators are classified as to their:
Service and type.
50
And acetylene cylinder has a safety device called a _____________ that will melt in case of a fire allowing gas to escape thereby preventing an explosion.
A fusible plug.
51
A _________ tube is used to operate the regulator gauge indicator needle.
Bourdon.
52
A carbonizing flame is said to have too much:
Acetylene.
53
The "R" in the AWS classification R65 stands for:
Rod.
54
The only process acceptable for joining __________ cast iron is braze welding.
Malleable.
55
A braze weld cannot stand up to a fusion weld when the product is:
Subjected to intense heat.
56
When referring to welding, a tack is used to:
Hold the components in place.
57
A correctly performed cut should have draglines that are:
Straight.
58
When attempting to cut bolts off flush with the surface of a plate you would use a _________ cutting tip.
Rivet.
59
Metal should be heated until it reaches its ________________ before flame cutting begins.
Kindling point.
60
A number of worksites have instituted a policy where no employee is allowed to lift more than:
23 kg or 50 pounds.
61
A higher ________ setting results in a wider, flatter weld bead with shallower penetration when using a wire feeder system.
Voltage.
62
When using a push system of wire drive it is recommended that it does not exceed a distance of _____ meters.
4.5 m or 15 feet.
63
When selecting a filler wire for use with the GMAW process, the main factor you should consider is:
That the composition will match the base metal.
64
When added in small amounts to an inert gas like argon, oxygen will:
Increase puddle fluidity.
65
Is shielding gas that is primarily used for welding mild steel is:
Carbon dioxide.
66
The weld lead on a machine that is DCEP would be connected to the ______ post.
Positive.
67
The liner used on GMAW system should be cleaned by:
Blowing it out with clean compressed air.
68
When using an FCAW electrode with a classification of E70T-2, the T means:
Tubular wire.
69
Basic type core wires use a ____________ mode of weld transfer.
Globular.
70
Most SAW electrode wires are:
Solid and rigid.
71
And electrode extension of ___ times the diameter of the electrode is a good starting point for SAW.
Eight.
72
With a 60 cycle AC power source, the current changes direction __times per second.
120 times per second.
73
With constant current type welding machines, what voltage range is normally needed to initiate an arc?
50 to 100 Volts.
74
A #3 welding cable is physically larger than a #4 welding cable. True or false?
True.
75
A 1/O welding cable is physically larger then a #1 welding cable. True or false?
True.
76
When using a SMAW welding machine, a normal arc length is ___________ the diameter of the core wire.
Equal to.
77
Using the AWS classification system, the letter E in E6010 stands for:
Electrode.
78
A term used to describe joint alignment is:
Hi – low.