121.11 Flashcards
Where is the original copy of tools and appliances checklist kept, and where is the copy kept?
The original copy will be kept on the apparatus and a copy in the company storeroom.
What time will the on duty platoon commander of companies insure inspection of apparatus and tools and appliances? Where is info recorded?
The on duty commander will ensure that the inspection is done daily at 0700. Upon completion, entry to journal will be made stating “checked tools and appliances utilizing checklist”
What are the guidelines for backing department vehicles?
- Department vehicles will be driven around the block rather than be backed or turned around in the street. If it is necessary to back vehicles, the utmost care will be taken. 2. Department vehicles will not be backed without adequate assistance of at least one other member of the Department. 3. When backing up, the apparatus will be watched by the officer in charge and the ambulance will be watched by the ambulance crew person who is not driving. 4. All available members will assist in guiding vehicles into quarters and in such other situations where circumstances dictate the necessity for extreme caution.
When shall all electrically operated devices such as lights, warning signals, AC units, etc be turned off?
Upon arrival on the scene all devices will be turned off as soon as they are no longer serving a useful purpose. In all cases, these devices will be turned off before shutting down the vehicle’s engine.
How often is the oil in the crankcase of apparatus checked?
Daily
What is the proper procedure used to check road transmissions?
To check the fluid level, start at operating temperature and the engine operating at 1000 rpm. Remove the dipstick, clean, reinsert, remove again, and check the fluid level. If the fluid level is low, add fluid to the “full” mark. Do not overfill as foaming may result, causing air bubbles in the fluid which may cause transmission failure due to improper lubrication of parts. Use only approved transmission fluid.
What is the maximum distance hose that may be extended past the foam eductor?
200ft
How often are grease fittings on apparatus lubricated?
They will be lubricated once a month, or on the basis of service performed
How often are priming pumps checked and lubricated?
Checked daily and lubricated after each use according to type of pump.
How often are discharge gates checked and lubricated?
Tested for free operation daily and lubricated when necessary.
How often are relief valves checked and lubricated?
Operated at least daily and lubricated in accordance with the pump operator procedure.
How often are apparatus radiators checked and what is the proper procedure for filling a hot radiator with cold water?
The coolant level in radiators will be checked daily; however, no radiator cap will be removed when the engine is hot and there is a chance that overpressure could release coolant and cause burns. Allow the engine to cool before removing the radiator cap. Cold water will not be placed in the hot radiator of any apparatus, except slowly and with the engine running.
At what temperature do the lug nut indicators overheat and blister and eventually fail.
248F
When a motor vehicle operator’s license is suspended or revoked, what will the member do and to whom is it addressed?
Special Report to the Safety Officer, through their appropriate Division Head,
When refueling apparatus or vehicles what precautions will be taken?
- No open flame will be permitted to burn nearby. 2. Use only the safety type cans provided by the Department. 3. Smoking will not be permitted. 4. During normal refueling, engines of vehicles will not be running.
When should the gaskets in the barrels of tips of play pipes, wagon pipes, monitor nozzles, and ladder pipes be inspected?
Monthly and after each use.
How should the company numbers be stenciled on fabric-covered hose?
will be maintained in a legible condition and will be placed approximately three feet from couplings with paint provided by the Apparatus Division.
How many 1 ½ pre-connected lines will be equipped on wagons? What are their lengths?
3 pre-connect lines. One line will be 350 feet in length, and the two remaining lines may vary from 150 feet to 250 feet in length.
What must members do whenever there is a change in the status of their motor vehicle operator’s license?
Special Report to the Safety Officer, through their appropriate Division Head
What shall be done if Department vehicles receive the incorrect type of fuel?
Company officers will notify AD immediately. Do not start the vehicle until AD decides how to best handle the situation.
How will tire pressure for all apparatus, vehicles, and equipment be maintained?
at the proper level, as marked on the vehicle tire.
Who is responsible for the daily inspection and maintenance of all EMS equipment, and where is the equipment carried on apparatus?
On-duty company officers and members will be responsible for the daily inspection and maintenance of all EMS equipment. will carry the EMS equipment in one of the right side compartments.
Who is responsible for placing apparatus wheel chocks?
Driver
What are the guidelines for cleaning apparatus?
When cleaning apparatus, water will not be applied into cabs of apparatus or vehicles with hose lines. Instead, a mop or sponge will be used. This also applies to compartments as well as floorboards, particularly where they are equipped with floor mats. 2. The underside of apparatus, including engines, chassis, springs, etc., may be steamed cleaned at an approved facility after permission has been received from AD. No steam or detergent will be used on top of engines around the carburetor, air cleaner or electrical wiring. 3. Apparatus will be thoroughly greased immediately after being steam cleaned. Any grease linings that cannot be lubricated will be reported to AD.
