107 Test Flashcards
A coiled twist wound around itself and secured to its base is called a:
Bantu Knot
A common way to analyze the overall direction of a hairstyle is according to how the hair moves in relation to the:
Face
A diffuser is attached to blow dryer to:
Soften airflow
A fine-tooth tail comb is also known as a:
Drawing comb
A hard press refers to applying the pressing comb:
Twice on each side with more pressure and heat
A Master Sketcher comb is used for:
Backcombing
A molding technique that is based on wrapping hair over the curves of the head and then drying the hair under a hooded dryer is called:
Hair wrapping
A review of client satisfaction occurs during which of the following service essentials?
Complete
A roller set procedure may involve some backbrushing or backcombing for all of the following reasons EXCEPT:
To disconnect shapes
A small round bush would be used to achieve:
Curlier looks on short hair
Adding finishing touches to customize the style, such as piecing the hair for additional texture or combing it smooth for a very polished look, is the process called:
Detailing
Along with the right product, hair molding involves two setting procedures:
Distribute and mold
Always feed the-ends of the hair all the way through the curling iron to avoid crimped or:
Fishhook ends
Ask questions to discover client’s wants and needs during which of the following service essentials?
Consult
Backcombing and backbrushing work best on hair that has been:
Texturized
Base size includes both the width and:
Length of the base
Blow dryers vary in the amount of wattage generally from:
1,000-1,800 watts
Curlier hair effects are produced by using which of the following roller sizes?
Small diameter rollers
Depending on the client’s hair texture, how long does it usually take for a hair to lock to form?
6 months to a year
Disinfected tools and multi-use supplies should be stored in a(n):
Clean, dry, covered container or cabinet
During hair pressing, fine hair requires which of the following actions?
Apply less heat
During the thermal iron procedure what is applied to achieve the intended degree of volume of closeness?
Base controls
Fingerwaves with low ridges are known as:
Shadow waves
Finishing procedures are preformed while the hair is:
Dry
Flat pincurls are used to create:
Closeness
For hair 3” (7.5 cm) or longer, detangle hair starting from the ends working toward the scalp and:
Use a pick for tightly curled textures
Hair can be shampooed immediately without disturbing locks when using which technique?
Latched (interlock) technique
Hair that is held at a 45” angle above the center of the base and rolled to sit in the upper portion of the base, but not on or above the parting, can be referred to as:
Overdirected
Heavily soiled thermal irons/pressing combs may be cleaned first, before disinfecting, with:
Fine steel wool
How do most clients choose to dry the hair after of a molding procedure?
By letting the hair dry
How is the smooth hair effect accomplished during a hair pressing service?
Pressing the heated spine of the comb against the hair
How often should very dry hair be shampooed?
Once a week
Hydrogen bonds are physical bonds that are weakened or broken by water or:
Heat
If the goal is to quickly dry the hair, a barber would chose which of the following brushes?
Vent brush
Immersing in an approved EPA-registered disinfectant after precleaning applies to all of the following items EXCEPT:
Thermal irons
In hairstyling, carving out areas where a specific movement or volume is desired means to section or:
Scale
In the basic level of observation you determine:
where volume is positioned
In the detail level of observation, you identify the types of textures you see such as wavy, curly, tightly curled, combination and:
Straight
In what direction should a blow dryer’s airflow be directed?
Down the hairstrand
In which level of observation do you observe the overall direction the hair is moving?
Abstract
Large diameter tools/brushes produce large waves and are considered:
Slow texture speed
Manipulating wet hair into straight or curved lines to create a pattern is called:
Molding
Optional techniques used to increase expansion and lasting power by creating a hair cushion or mesh at the base are called backcombing and:
Backbrushing
Parallel distribution can be described as straight or curved lines that:
Are distributed from multiple points of origin
Pressing combs are made of stainless steel or:
Brass
Professional curling irons are also referred to as:
Marcel irons
