Wireless Networking Flashcards
You need to install wireless Internet access in an open warehouse environment. After installing the equipment, the technician notices varying signal strengths throughout the warehouse. How do you make sure there is full coverage?
Turn on broadcast key rotation.
Change the encryption method used on all the APs.
Change the antenna placement.
Change the antenna placement.
It is imperative that a good site survey is completed before you install your wireless network. Trying various types of antennas and their placements is the key to covering the whole wireless area
Which of the following uses a certificate on both the server and client to provide the best wireless security with 802.1X (but is hardest to implement)?
AES
TTLS
TLS
TLS
TLS provides really good wireless security, but it’s hard to implement because you need to install a certificate on your server and also on all your clients. TTLS only uses a server-side certificate
What is the frequency range of the IEEE 802.11g standard?
2.4 Gbps
5 Gbps
2.4 GHz
2.4 GHz
The IEEE 802.11b and IEEE 802.11g both run in the 2.4 GHz RF range
Which devices can interfere with the operation of a wireless network because they operate on similar frequencies? (Choose two.)
Copier
Microwave oven
Toaster
Cordless phone
Microwave oven
Cordless phone
If you are running 802.11b/g frequency, which most networks are, then you can receive interference from microwave ovens and cordless phones
Which wireless standard allows you to channel-bond to increase bandwidth and uses both the 2.4 GHz and 5 GHz frequencies?
- 11b
- 11a
- 11n
- 11n
802. 11n uses channel bonding of both the 2.4 GHz range and the 5 GHz range to get increased bandwidth of over 100 Mbps
Which of the following is considered a PAN?
AES
SSID
Bluetooth
Bluetooth
Bluetooth works wirelessly to connect our phones, keyboards, and so on in small areas, also known as personal area networks (PANs)
How many non-overlapping channels are available with 802.11a?
3
12
23
12
The IEEE 802.11a standard provides up to 12 non-overlapping channels, or up to 23 if you add the 802.11h standard
What is the maximum data rate for the 802.11a standard?
11 Mbps
22 Mbps
54 Mbps
54 Mbps
The IEEE 802.11a standard provides a maximum data rate of up to 54 Mbps
You need to install wireless on multiple floors of a large building and maintenance area. What is your first concern before installing the APs?
Authentication
Encryption
Channel overlap
Channel overlap
If you have a large area to cover with wireless, you need to be concerned with channel overlap
What is the maximum data rate for the 802.11b standard?
6 Mbps
11 Mbps
22 Mbps
11 Mbps
The IEEE 802.11b standard provides a maximum data rate of up to 11 Mbps
You connect a new host to your company’s wireless network. The host is set to receive a DHCP address and the WPA2 key is entered correctly. However, the host cannot connect to the network. What can the problem be?
DNS is not configured on the host.
MAC filtering is enabled on the AP.
The network has run out of wireless connections.
MAC filtering is enabled on the AP.
If everything is correctly configured on the host, then MAC filtering would stop the host from connecting to the AP. If you try to connect and can’t, check the AP’s settings
Which is the highest encryption that WPA2 can use?
AES-CCMP
PPK via IV
PSK
AES-CCMP
The IEEE 802.11i standard replaced Wired Equivalent Privacy (WEP) with a specific mode of the Advanced Encryption Standard (AES) known as the Counter Mode Cipher Block Chaining-Message Authentication Code (CBC-MAC) protocol. This allows AES-Counter Mode CBC-MAC Protocol (AES-CCMP) to provide both data confidentiality (encryption) and data integrity
Which additional configuration step is necessary in order to connect to an access point that has SSID broadcasting disabled?
Set the SSID value in the client software to public.
Configure open authentication on the AP and the client.
Set the SSID value on the client to the SSID configured on the AP.
Set the SSID value on the client to the SSID configured on the AP.
If you disable SSID broadcasting, which you should, then you must configure the SSID name on the clients that need to connect to the AP
Which spread-spectrum technology does the 802.11b standard define for operation?
IR
DSSS
FHSS
DSSS
The IEEE 802.11b standard uses Direct Sequence Spread Spectrum (DSSS). If you are running 802.11g, it uses Orthogonal Frequency Division Multiplexing (OFDM)
Which wireless LAN design ensures that a mobile wireless client will not lose connectivity when moving from one access point to another?
Using adapters and access points manufactured by the same company
Overlapping the wireless cell coverage by at least 10 percent
Configuring all access points to use the same channel
Overlapping the wireless cell coverage by at least 10 percent
If you are running an extended service set (meaning more than one AP with the same SSID), you need to overlap the cell coverage by 10 percent or more so clients will not drop out while roaming
