T7 - Station equipment [4 Exam Questions - 4 Groups] Flashcards

1
Q

Which term describes the ability of a receiver to detect the presence of a signal?

A. Linearity

B. Sensitivity

C. Selectivity

D. Total Harmonic Distortion

A

B. Sensitivity

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

What is a transceiver?

A.A type of antenna switch

B. A unit combining the functions of a transmitter and a receiver

C. A component in a repeater which filters out unwanted interference

D. A type of antenna matching network

A

B. A unit combining the functions of a transmitter and a receiver

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Which of the following is used to convert a radio signal from one frequency to another?

A. Phase splitter

B. Mixer

C. Inverter

D. Amplifier

A

B. Mixer

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Which term describes the ability of a receiver to discriminate between multiple signals?

A. Discrimination ratio

B. Sensitivity

C. Selectivity

D. Harmonic Distortion

A

C. Selectivity

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

What is the name of a circuit that generates a signal of a desired frequency?

A. Reactance modulator

B. Product detector

C. Low-pass filter

D. Oscillator

A

D. Oscillator

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

What device takes the output of a low-powered 28 MHz SSB exciter and produces a 222 MHz output signal?

A. High-pass filter

B. Low-pass filter

C. Transverter

D. Phase converter

A

C. Transverter

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

What is meant by term ‘‘PTT’’?

A. Pre-transmission tuning to reduce transmitter harmonic emission

B. Precise tone transmissions used to limit repeater access to only certain signals

C. A primary transformer tuner use to match antennas

D. The push to talk function which switches between receive and transmit

A

D. The push to talk function which switches between receive and transmit

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Which of the following describes combining speech with an RF carrier signal?-

A. Impedance matching

B. Oscillation

C. Modulation

D. Low-pass filtering

A

C. Modulation

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Which of the following devices is most useful for VHF weak-signal communication?

A. A quarter-wave vertical antenna

B. A multi-mode VHF transceiver

C. An omni-directional antenna

D. A mobile VHF FM transceiver

A

B. A multi-mode VHF transceiver

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What device increases the low-power output from a handheld transceiver?

A. A voltage divider

B. An RF power amplifier

C. An impedance network

D. All of these choices are correct

A

B. An RF power amplifier

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Where is an RF preamplifier installed?

A. Between the antenna and receiver

B. At the output of the transmitter’s power amplifier

C. Between a transmitter and antenna tuner

D. At the receiver’s audio output

A

A. Between the antenna and receiver

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What can you do if you are told your FM handheld or mobile transceiver is over-deviating?

A. Talk louder into the microphone

B. Let the transceiver cool off

C. Change to a higher power level

D. Talk farther away from the microphone

A

D. Talk farther away from the microphone

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

What would cause a broadcast AM or FM radio to receive an amateur radio transmission unintentionally?

A. The receiver is unable to reject strong signals outside the AM or FM band

B. The microphone gain of the transmitter is turned up too high

C. The audio amplifier of the transmitter is overloaded

D. The deviation of an FM transmitter is set too low

A

A. The receiver is unable to reject strong signals outside the AM or FM band

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Which of the following may be a cause of radio frequency interference?

A. Fundamental overload

B. Harmonics

C. Spurious emissions

D. All of these choices are correct

A

D. All of these choices are correct

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Which of the following is a way to reduce or eliminate interference by an amateur transmitter to a nearby telephone?

A. Put a filter on the amateur transmitter

B. Reduce the microphone gain

C. Reduce the SWR on the transmitter transmission line

D. Put a RF filter on the telephone

A

D. Put a RF filter on the telephone

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

How can overload of a non-amateur radio or TV receiver by an amateur signal be reduced or eliminated?

A. Block the amateur signal with a filter at the antenna input of the affected receiver

B. Block the interfering signal with a filter on the amateur transmitter

C. Switch the transmitter from FM to SSB

D. Switch the transmitter to a narrow-band mode

A

A. Block the amateur signal with a filter at the antenna input of the affected receiver

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

Which of the following actions should you take if a neighbor tells you that your station�s transmissions are interfering with their radio or TV reception?

A. Make sure that your station is functioning properly and that it does not cause interference to your own radio or television when it is tuned to the same channel

B. Immediately turn off your transmitter and contact the nearest FCC office for assistance

C. Tell them that your license gives you the right to transmit and nothing can be done to reduce the interference

D. Install a harmonic doubler on the output of your transmitter and tune it until the interference is eliminated

A

A. Make sure that your station is functioning properly and that it does not cause interference to your own radio or television when it is tuned to the same channel

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

Which of the following may be useful in correcting a radio frequency interference problem?

A. Snap-on ferrite chokes

B. Low-pass and high-pass filters

C. Band-reject and band-pass filters

D. All of these choices are correct

A

D. All of these choices are correct

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

What should you do if something in a neighbor�s home is causing harmful interference to your amateur station?

A. Work with your neighbor to identify the offending device

B. Politely inform your neighbor about the rules that prohibit the use of devices which cause interference

C. Check your station and make sure it meets the standards of good amateur practice

D. All of these choices are correct

A

D. All of these choices are correct

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

What is a Part 15 device?

A. An unlicensed device that may emit low powered radio signals on frequencies used by a licensed service

B. A type of amateur radio that can legally be used in the citizen�s band

C. A device for long distance communications using special codes sanctioned by the International Amateur Radio Union

D. A type of test set used to determine whether a transmitter is in compliance with FCC regulation 91.15

A

A. An unlicensed device that may emit low powered radio signals on frequencies used by a licensed service

21
Q

What might be the problem if you receive a report that your audio signal through the repeater is distorted or unintelligible?

A. Your transmitter may be slightly off frequency

B. Your batteries may be running low

C. You could be in a bad location

D. All of these choices are correct

A

D. All of these choices are correct

22
Q

What is a symptom of RF feedback in a transmitter or transceiver?

A. Excessive SWR at the antenna connection

B. The transmitter will not stay on the desired frequency

C. Reports of garbled, distorted, or unintelligible transmissions

D. Frequent blowing of power supply fuses

A

C. Reports of garbled, distorted, or unintelligible transmissions

23
Q

What might be the first step to resolve cable TV interference from your ham radio transmission?

A. Add a low pass filter to the TV antenna input

B. Add a high pass filter to the TV antenna input

C. Add a preamplifier to the TV antenna input

D. Be sure all TV coaxial connectors are installed properly

A

D. Be sure all TV coaxial connectors are installed properly

24
Q

What is the primary purpose of a dummy load?

A. To prevent the radiation of signals when making tests

B. To prevent over-modulation of your transmitter

C. To improve the radiation from your antenna

D. To improve the signal to noise ratio of your receiver

A

A. To prevent the radiation of signals when making tests

25
Q

Which of the following instruments can be used to determine if an antenna is resonant at the desired operating frequency?

A. A VTVM

B. An antenna analyzer

C. A Q meter

D. A frequency counter

A

B. An antenna analyzer

26
Q

What, in general terms, is standing wave ratio (SWR)?

A. A measure of how well a load is matched to a transmission line

B. The ratio of high to low impedance in a feed line

C. The transmitter efficiency ratio

D. An indication of the quality of your station�s ground connection

A

A. A measure of how well a load is matched to a transmission line

27
Q

What reading on an SWR meter indicates a perfect impedance match between the antenna and the feed line?

A. 2 to 1

B. 1 to 3

C. 1 to 1

D. 10 to 1

A

C. 1 to 1

28
Q

What is the approximate SWR value above which the protection circuits in most solid-state transmitters begin to reduce transmitter power?

A. 2 to 1

B. 1 to 2

C. 6 to 1

D. 10 to 1

A

A. 2 to 1

29
Q

What does an SWR reading of 4:1 indicate?

A. Loss of -4dB

B. Good impedance match

C. Gain of +4dB

D. Impedance mismatch

A

D. Impedance mismatch

30
Q

What happens to power lost in a feed line?

A. It increases the SWR

B. It comes back into your transmitter and could cause damage

C. It is converted into heat

D. It can cause distortion of your signal

A

C. It is converted into heat

31
Q

What instrument other than an SWR meter could you use to determine if a feed line and antenna are properly matched?

A. Voltmeter

B. Ohmmeter

C. Iambic pentameter

D. Directional wattmeter

A

D. Directional wattmeter

32
Q

Which of the following is the most common cause for failure of coaxial cables?

A. Moisture contamination

B. Gamma rays

C. The velocity factor exceeds 1.0

D. Overloading

A

A. Moisture contamination

33
Q

Why should the outer jacket of coaxial cable be resistant to ultraviolet light?

A. Ultraviolet resistant jackets prevent harmonic radiation

B. Ultraviolet light can increase losses in the cable�s jacket

C. Ultraviolet and RF signals can mix together, causing interference

D. Ultraviolet light can damage the jacket and allow water to enter the cable

A

D. Ultraviolet light can damage the jacket and allow water to enter the cable

34
Q

What is a disadvantage of air core coaxial cable when compared to foam or solid dielectric types?

A. It has more loss per foot

B. It cannot be used for VHF or UHF antennas

C. It requires special techniques to prevent water absorption

D. It cannot be used at below freezing temperatures

A

C. It requires special techniques to prevent water absorption

35
Q

Which of the following is a common use of coaxial cable?

A. Carrying dc power from a vehicle battery to a mobile radio

B. Carrying RF signals between a radio and antenna

C. Securing masts, tubing, and other cylindrical objects on towers

D. Connecting data signals from a TNC to a computer

A

B. Carrying RF signals between a radio and antenna

36
Q

What does a dummy load consist of?

A. A high-gain amplifier and a TR switch

B. A non-inductive resistor and a heat sink

C. A low voltage power supply and a DC relay

D. A 50 ohm reactance used to terminate a transmission line

A

B. A non-inductive resistor and a heat sink

37
Q

Which instrument would you use to measure electric potential or electromotive force?

A. An ammeter

B. A voltmeter

C. A wavemeter

D. An ohmmeter

A

B. A voltmeter

38
Q

What is the correct way to connect a voltmeter to a circuit?

A. In series with the circuit

B. In parallel with the circuit

C. In quadrature with the circuit

D. In phase with the circuit

A

B. In parallel with the circuit

39
Q

How is an ammeter usually connected to a circuit?

A. In series with the circuit

B. In parallel with the circuit

C. In quadrature with the circuit

D. In phase with the circuit

A

A. In series with the circuit

40
Q

Which instrument is used to measure electric current?

A. An ohmmeter

B. A wavemeter

C. A voltmeter

D. An ammeter

A

D. An ammeter

41
Q

What instrument is used to measure resistance?

A. An oscilloscope

B. A spectrum analyzer

C. A noise bridge

D. An ohmmeter

A

D. An ohmmeter

42
Q

Which of the following might damage a multimeter?

A. Measuring a voltage too small for the chosen scale

B. Leaving the meter in the milliamps position overnight

C. Attempting to measure voltage when using the resistance setting

D. Not allowing it to warm up properly

A

C. Attempting to measure voltage when using the resistance setting

43
Q

Which of the following measurements are commonly made using a multimeter?

A. SWR and RF power

B. Signal strength and noise

C. Impedance and reactance

D. Voltage and resistance

A

D. Voltage and resistance

44
Q

Which of the following types of solder is best for radio and electronic use?

A. Acid-core solder

B. Silver solder

C. Rosin-core solder

D. Aluminum solder

A

C. Rosin-core solder

45
Q

What is the characteristic appearance of a cold solder joint?

A. Dark black spots

B. A bright or shiny surface

C. A grainy or dull surface

D. A greenish tint

A

C. A grainy or dull surface

46
Q

What is probably happening when an ohmmeter, connected across an unpowered circuit, initially indicates a low resistance and then shows increasing resistance with time?

A. The ohmmeter is defective

B. The circuit contains a large capacitor

C. The circuit contains a large inductor

D. The circuit is a relaxation oscillator

A

B. The circuit contains a large capacitor

47
Q

Which of the following precautions should be taken when measuring circuit resistance with an ohmmeter?

A. Ensure that the applied voltages are correct

B. Ensure that the circuit is not powered

C. Ensure that the circuit is grounded

D. Ensure that the circuit is operating at the correct frequency

A

B. Ensure that the circuit is not powered

48
Q

Which of the following precautions should be taken when measuring high voltages with a voltmeter?

A. Ensure that the voltmeter has very low impedance

B. Ensure that the voltmeter and leads are rated for use at the voltages to be measured

C. Ensure that the circuit is grounded through the voltmeter

D. Ensure that the voltmeter is set to the correct frequency

A

B. Ensure that the voltmeter and leads are rated for use at the voltages to be measured