Brainscape's Knowledge GenomeTM

Browse over 1 million classes created by top students, professors, publishers, and experts.


See full index

B737 > SV - Fire Protection/Warning System > Flashcards

SV - Fire Protection/Warning System Flashcards

1
Q

Fire detection and extinguishing systems are located at which of the following areas?

A

Engines, APU, Lavatories, Cargo Compartments

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

The _________ powers engine overheat and fire detection:

A

battery bus

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What happens when the engine fire warning switch is pulled up?

A

Closes fuel, hydraulic shutoff, and engine bleed air valves. Disables the reverser, trips the respective generator control circuit breaker, and deactivates the engine-driven hydraulic pump.

FH-BARGE
F - Fuel Shutoff Valves (Spar and HMU)
H - Hydraulic Shutoff Valve
B - Bleed Air Valve
R - Disable Reverser
G - Disable Generator
H - Deactivate Hydraulic Pump
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

When the FAULT/INOP and OVHT/FIRE TEST Switch is placed in the OVHT/FIRE position, should the FAULT
light illuminate?

A

No

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

If you are on the ground, what additional indications of an APU fire occur?

A

The wheel well APU fire warning horn sounds

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

The APU ground control panel contains an APU fire warning light, an APU BOTTLE DISCHARGE switch, an APU fire control handle, and an APU HORN CUTOUT switch and is located in the __________ .

A

main wheel well

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

The Cargo Compartment Fire Suppression System contains how many fire extinguisher bottle(s)?

A

two

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What should happen when pushing the Cargo Fire TEST Switch?

A

Both Extinguisher (EXT) Test Lights should illuminate green

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

If the Overheat Detector Select (OVHT DET) switches is in the NORMAL position, _______.

A

detection loop A and B are active

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

The ______light illuminates when both loops in one or both cargo compartments have failed?

A

DETECTOR FAULT

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

If the Cargo Fire Bottle Discharge (DISCH) light is illuminated (amber), what does it mean?

A

Indicates either extinguisher bottle has discharged

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What happens on the B737-800, after the Cargo Fire System is armed, if the Cargo Fire Discharge (DISCH)
Switch is pushed, and the first extinguisher bottle is discharged.

A

A timer is then set for 60 minutes to discharge the second bottle.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

When smoke is detected in the lavatory, what is the flight deck indication?

A

There is no flight deck indication

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

The Lavatory Fire Extinguisher would indicate what color to indicate that the Heat Activated Nozzle has been discharged? (CHECK)

A

Aluminum

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

With the If the OVHT DET switch is in normal and one engine overheat and fire detection loop fails, what
happens?

A

The failed loop is automatically deactivated and the remaining loop functions as a single loop detector

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

What does an illuminated amber FAULT light on the overheat fire protection panel indicate with the OVHT
DET switch in normal?

A

Both detector loops for an engine have failed

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

What does an illuminated amber FAULT light on the overheat fire protection panel indicate with the OVHT
DET switch selected to A?

A

The A detector loop for an engine has failed

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

A _____ has occurred if both MASTER CAUTION lights, the OVHT/DET system annunciator light, and the related ENG OVERHEAT light illuminate.

A

An engine overheat

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

The indications of an engine fire are:

A

All related engine overheat alert indications illuminate

The fire warning bell sounds, both master FIRE WARNING lights illuminate, the related engine fire
warning switch illuminates

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

The engine fire warning switches are unlocked by?

A

Illumination of an engine fire warning switch, illumination of an ENG OVERHEAT light, or manually by
pushing the fire warning switch override

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

What occurs to the engine fuel system when pulling the engine fire warning switch up?

A

Closes both the engine fuel shutoff valve at the HMU and the spar fuel shutoff valve

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

What occurs to the respective hydraulic system when pulling the engine fire warning switch up?

A

Closes the hydraulic fluid shutoff valve and deactivates the engine driven hydraulic pump LOW PRESSURE light

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

When the Fire Warning BELL CUTOUT Switch is pushed it extinguishes both master FIRE WARN lights, silences the fire warning bell and ___________.

A

resets system for additional warnings

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
Q

When positioning the EXT TEST Switch to 1 or 2, circuit continuity from the squib to __________ is verified.

A

both engines and APU fire switches

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
25
Q

What happens when placing the Fault/Inoperative (FAULT/INOP) and Overheat/Fire (OVHT/FIRE) TEST
Switch to the FAULT/INOP position?

A

Tests the fault detection circuits for both engines and the APU

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
26
Q

What happens when placing the Fault/Inoperative (FAULT/INOP) and Overheat/Fire (OVHT/FIRE) TEST
Switch to the OVHT/FIRE position?

A

Tests overheat and fire detection loops on both engines and APU, and wheel well fire detector

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
27
Q

What happens when there is an illuminated APU Fire Warning Switch, in the down position?

A

Unlocks the APU fire warning switch

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
28
Q

_____ lights will illuminate during a number 1 engine overheat?

A

ENG 1 OVERHEAT, MASTER CAUTION, and OVHT/DET system annunciator

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
29
Q

What does an illuminated red WHEEL WELL Fire Warning Light indicate?

A

A fire in the main gear wheel well

30
Q

An illuminated engine BOTTLE DISCHARGE light indicates _____.

A

the related fire extinguisher bottle has discharged

31
Q

An illuminated APU DET INOP light indicates_____.

A

APU detector loop has failed

32
Q

An illuminated APU BOTTLE DISCHARGE light indicates_____.

A

the APU extinguisher bottle has discharged

33
Q

Pushing the Master Fire Warning (FIRE WARN BELL CUTOUT) on the glareshield have the same results as
pushing the fire warning bell cutout switch on the overheat/fire protection panel?

A

True

34
Q

What happens when pushing the FWD Cargo Fire ARM Switch?

A

Arms the extinguisher for the forward cargo compartment

35
Q

What happens when pressing either MASTER CAUTION light after both lights are extinguished?

A

Resets the annunciator light for further cautions

36
Q

Single failures in dual/redundant systems do not illuminate MASTER CAUTION light. How do you recall the system failure?

A

Pressing either system annunciator light panel

37
Q

If ____________________are pressed, both Master Fire Warning lights are extinguished, the fire warning bell is silenced, and the system is reset for additional warnings.

A

either MASTER FIRE WARNING light or the fire warning bell cutout switch

38
Q

What do the Cabin Altitude and Takeoff Configuration Warnings commonly use when activated?

A

the same intermittent tone

39
Q

What conditions cause the takeoff configuration warning horn to sound?

A

Trailing edge flaps skew or asymmetry, speed brake lever not in the DOWN position, or spoiler control valve is open providing pressured hydraulic fluid to the ground spoiler interlock valve

Stabilizer trim not set in the takeoff range, flaps not in the takeoff range, LE devices are not configured
for takeoff, or the parking brake is set.

SSS-FLP 
Speed brake lever not DOWN
Spoiler control valve open/ground spoiler interlock valve pressurized
Stabilizer Trim not set for takeoff
Flaps (TE) skew/asymmetry
Flaps (TE) not set for takeoff
LE devices not configured for takeoff
Parking brake set
40
Q

What happens anytime the aircraft is below 800 feet RA, in landing configuration and any gear not down and locked?

A

A steady horn sounds

41
Q

During which conditions does pushing the Landing Gear Warning Cutout Switch silence landing gear configuration warning aural?

A

Flaps up through 10 and below 800 feet RA

42
Q

What does the The Proximity Switch Electronic Unit (PSEU) monitor?

A

Takeoff and landing configuration warnings

Landing gear and air / ground sensing

43
Q

On the ground, what does an illuminated Proximity Switch Electronic Unit (PSEU) indicate.

A

A fault is detected in the PSEU, or an overwing exit flight lock fails to disengage when commanded

44
Q

The Proximity Switch Electronic Unit (PSEU) _____________ in flight.

A

is inhibited from thrust lever advance for takeoff until 30 seconds after landing

45
Q

As the throttles are advanced, what does it mean if the Takeoff Configuration Warning Light illuminates red?

A

The airplane is not configured correctly for takeoff

46
Q

What does an illuminated Cabin Altitude Warning Light indicates?

A

At 10,000 feet if the cabin has not been pressurized

47
Q

What happens when the maximum operating airspeed of Vmo/Mmo is exceeded?

A

The Mach / airspeed warning system provides an aural warning (clacker)

48
Q

The indication of an impending stall is_____?

A

an artificial stall warning device (stick shaker)

49
Q

Which is true in regard to the MACH AIRSPEED WARNING TEST switches and the STALL WARNING TEST switches?

A

are inhibited while airborne

50
Q

When is altitude alerting inhibited?

A

When the trailing edge flaps are extended to 25 or greater, or while G/S is captured

51
Q

At what point prior to reaching the selected altitude does a white box shows around the selected altitude display, the box around the current altitude becomes bold and a momentary tone sounds?

A

900 feet

52
Q

If the selected altitude is deviated by ____ feet, a momentary tone sounds, the current altitude box turns amber and ____________.

A

300; begins to flash

53
Q

What inhibits Ground Proximity Warning System look ahead terrain and radio altitude based alerts?

A

Actual windshear warning

54
Q

Approximately how far from the projected impact will the look ahead terrain alert “Terrain, terrain, pull up” sound with the terrain shown in solid red on the navigation display?

A

20 to 30 secs

55
Q

Approximately how far from projected impact will the look ahead terrain alert “Caution, terrain” will sound with terrain shown in solid amber on the navigation display?

A

40 to 60 secs

56
Q

In what speed realm does “Too low, terrain” aural alert occurs if the aircraft is at an unsafe terrain clearance with either the landing gear not down or flaps not in the landing configuration?

A

high speed

57
Q

If the aircraft experiences excessive altitude loss after a takeoff or go-around, the “__________” aural alert occurs.

A

“DON’T SINK”

58
Q

The Volume and repetition of the “GLIDESLOPE” aural alert rate ____________ as deviation _______________ below the glideslope

A

increase; increases

59
Q

When are new predictive windshear warning alerts are inhibited During takeoff and landing?

A

Between 100 knots and 50 ft RA

60
Q

What does an illuminated Inoperative (INOP) light on the Ground Proximity panel alert the pilot to?

A

A GPWS computer malfunction or power loss has occurred.

61
Q

In flight, the Ground Proximity System Test (SYS TEST) Switch is ______.

A

inhibited

62
Q

What does placing the Ground Proximity FLAP INHIBIT Switch to FLAP INHIBIT, inhibit?

A

Ground proximity TOO LOW FLAPS alert

63
Q

What does placing the Ground Proximity TERRAIN INHIBIT Switch to TERRAIN INHIBIT, inhibit?

A

Look-ahead terrain alerts and terrain displays

64
Q

When does the weather radar automatically begins scanning for windshear?

A

all answers are correct

65
Q

A(n) ____________ aural and a message is annunciated on the traffic display for Traffic advisories.

A

“TRAFFIC TRAFFIC”

66
Q

Resolution advisories provide ________and an aural warning to maintain or increase separation from traffic.

A

maneuver guidance

67
Q

What does placing the Transponder Mode Selector to TA (traffic advisory) ONLY do?

A

Enables the display of traffic advisory targets

68
Q

What does placing the Transponder Mode Selector to TA/RA do?

A

Enables the display of traffic advisory targets and resolution advisory (RA) targets

69
Q

What does pressing the Absolute Altitude Display Selector on the TCAS Controls (Transponder Panel) do?

A

Displays absolute altitude of TCAS targets

70
Q

In which TCAS Altitude Range Switch position sets TCAS display from 2700 feet below to 7000 feet above own aircraft?

A

Above (ABV)

71
Q

On the cartridge assembly (Tail Skid) on the -800 and -900 series, if the warning decal is ______, the cartridge must be replaced.

A

All red

B737 (15 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2024 Bold Learning Solutions. Terms and Conditions