Section 1 Ure

Question 1

What is the rated capacity of the positive displacement meter on the R14C fuel servicing module

Answer 1

600 gpm

Question 2

At what flow rate can fuel be pumped through one 2inch over wing nozzle on the R14C fuel servicing module?

Answer 2

100 gpm

Question 3

What component on the collapsible coated fabric fuel tank allows for removal of water?

Answer 3

Tank vent pipe assembly

Question 4

How far from the parking apron must the tanks be placed if the ABFDS is used to resupply the R14C fuel servicing module?

Answer 4

100 feet

Question 5

What must be taken into consideration when determining a convenient location to set up the R14C fuel servicing module?

Answer 5

Type of aircraft to be serviced

Question 6

Hearing protection must be worn when working within how many feet of the R14C operation?

Answer 6

50 feet

Question 7

What temperature must the engine of the R14C fuel servicing module reach during idle before you can increase the throttle setting?

Answer 7

120 F

Question 8

What is the minimum operating oil pressure for the R14C fuel servicing module at normal operating speed?

Answer 8

40psi

Question 9

When placed in the low mobility position what is the maximum ramp angle the R 14C can negotiate?

Answer 9

15 degrees

Question 10

What is the purpose of the float valve on the R 22 pump assembly?

Answer 10

To fill the engine tank

Question 11

When setting up the R 22 how many sections of 25 foot hose should be used to connect the R22 to the FFU-15E?

Answer 11

3

Question 12

After starting the R 22 how long should the engine be allowed to idle before increasing the throttle setting?

Answer 12

5 min

Question 13

At what flow rate is the FFU-15E filter separator capable of filtering petroleum fuels?

Answer 13

600 gpm

Question 14

How many elements are installed in the FFU-15E filter separator?

Answer 14

6

Question 15

How often should the filter separator elements in the FFU15E be replaced?

Answer 15

WHen the DP reaches 20 or every 3 years, whichever comes first

Question 16

The canisters in the FFU-15E filter separator are constructed of

Answer 16

Aluminum

Question 17

When setting up the FFU-15E how should it be placed in relation to the dike wall?

Answer 17

25 feet in front and centered on the dike wall

Question 18

When preparing the FFU-15E for shipment, complete all of the following except

Answer 18

Remove filter elements

Question 19

The TPI-4T-4A additive injector is capable of simultaneously injecting how many additives?

Answer 19

4

Question 20

What type of meter is installed on the TPI-4T-4A additive injector?

Answer 20

No meter

Question 21

When setting up the TPI-4T-4A additive injector where should the corrosion inhibitor and static dissipater additive tanks be placed?

Answer 21

On top of the injector cage.

Question 22

When must the injectors on the TPI-4T-4A be purged of all additives?

Answer 22

When the unit will be inoperative for more than 72 hours

Question 23

What ppe is required when calibrating the TPI-4T-4A?

Answer 23

Safety goggles

Question 24

All of the following things should be considered before starting a calibration run with the TPI-4T-4A except what?

Answer 24

Amount of additive will be injected

Question 25

The second purpose of the PMU-27M self-priming pump is refueling

Answer 25

Small aircraft

Question 26

What is the rated capacity of the PMU-27M self-priming pump?

Answer 26

50 gpm

Question 27

How many filter elements are installed in the PMU-27M filter separator?

Answer 27

3

Question 28

To facilitate priming, the PMU-27M self-priming pump is provided with a priming

Answer 28

Valve

Question 29

The 117 MRSP kit is equipped with how many 500 gallons sealed drums

Answer 29

4

Question 30

When preparing the PMU-27M for shipment complete all of the following except

Answer 30

Remove filter elements

Question 31

How many tanks are used when the ABFDS is installed on a C-5?

Answer 31

10

Question 32

What ABFDS Component tank Component prevents the buildup of fuel vapors inside the aircraft?

Answer 32

Automatic vapor eliminator

Question 33

On the ABFDS How many wafers valves make up the refuel/defuel manifold of each pumping module

Answer 33

4

Question 34

What is the rated capacity of the filter separator on the ADDS

Answer 34

300 gpm

Question 35

What fuel bladder component is used for removing water from the bladder?

Answer 35

Vertical vent pipe

Question 36

When positioning 50,000 gal fuel bladders Inside a diked area how far apart must the tanks be from each other?

Answer 36

6 feet

Question 37

Sealing clamps used for emergency repair of fuel bladders come in what sizes?

Answer 37

3 inch, 5 inch, 7 1/2 inch

Question 38

The FAM cart is capable of servicing up to how many receiver aircraft at one time?

Answer 38

3

Question 39

The FAM cart engine can run on all of the following fuels except

Answer 39

Gasoline

Question 40

For air shipment the inner tanks of empty cyrotainers of pressurized with dry nitrogen gas at a positive pressure of

Answer 40

15 to 25 psi

Question 41

Fuels personnel identify the tank vent valve by using a locally manufactured

Answer 41

Round aluminum disc

Question 42

During shipment the cryotainer inner tank pressure should not exceed what Maximum psi reading?

Answer 42

40 psi

Question 43

Which fuels can be used to operate the engine on the R14C fuel servicing module

Answer 43

Jet fuel and diesel