Random Questions Flashcards

1
Q

What is the first step to perform routine maintenance on mechanical equipment?
A. Isolate and lock all energy sources.
B. Notify supervisor.
C. Isolate energy sources.
D. Read owner’s manual.

A

A. Isolate and lock all energy sources

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

What is required when working from heights?
A. Hard hat.
B. Fall arrest equipment.
C. Safety glasses.
D. Steel-toed work boots

A

B. Fall Arrest Equipment

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What PPE is required when working in a high-traffic area?
A. Hearing protection.
B. Safety glasses.
C. High visibility clothing.
D. Steel-toed work boots.

A

C. High Visibility clothing

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Which type of tool is used to cut 16-gauge galvanized sheet metal?
A. Tin snips.
B. Locking pliers.
C. Side cutters.
D. Slip pliers.

A

A. Tin Snips

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

What is the procedure to drill a 1-in hole in a mild steel plate?
A. Scribe mark material, drill pilot hole, then drill final bit size.
B. Drill pilot hole, then drill final bit size.
C. Make punch mark, drill pilot holes, then drill final bit size.
D. Scribe mark material, then drill final bit size.

A

C. Make punch mark, drill pilot holes, then drill final bit size.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

When using nylon web slings, which type of guard is used on sharp edges?
A. Personalised sleeves.
B. Softeners.
C. 4 plies of cardboard.
D. Plastic angles.

A

A. Personalised sleeves.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Why is coolant or cutting oil used?
A. To speed up drill process.
B. To eliminate heat build-up.
C. To lubricate when drilling cast iron.
D. To contain metal filings when drilling.

A

B. To eliminate heat build-up.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What is done to prepare a vertical surface before using a magnetic drill?
A. Rough up surface to create porosity.
B. Lubricate surface with low viscosity grease.
C. Ensure surface is clean and smooth.
D. Apply continuous spray of water.

A

C. Ensure surface is clean and smooth.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Which tool is used to align rotating mechanical couplings?
A. Vernier calipers and magnetic bases.
B. Outside micrometer.
C. Dial indicator or a laser aligner.
D. Depth micrometer.

A

C. Dial indicator or a laser aligner.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

A conveyer belt is running out of line beneath a chute. What is the cause?
A. Belt tension is unbalanced.
B. Skirting is too close to belt.
C. Skirting is too far away from belt.
D. Scraper is out of alignment.

A

A. Belt tension is unbalanced.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What is the included angle of a drill bit for general drilling?
A. 56°
B. 59°
C. 112°
D. 118°

A

D. 118°

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What is the procedure to replace an oil sight glass on a centrifugal pump?
A. Lock out, isolate, drain, then change oil sight glass.
B. Isolate, lock out, drain, then change oil sight glass.
C. Drain, lock out, isolate, then change oil sight glass.
D. Lock out, drain, isolate, then change oil sight glass.

A

B. Isolate, lock out, drain, then change oil sight glass.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

A diesel engine lacks power. What is the cause?
A. Oil level is excessive.
B. Engine temperature is above normal.
C. Alignment is out of specifications.
D. Valves are incorrectly adjusted.

A

D. Valves are incorrectly adjusted.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

A manual operated pump jack fails to secure a load. What is the cause?
A. Contaminated cylinder oil.
B. Leaking seals.
C. Piston diameter too small.
D. Fully extended piston.

A

B. Leaking seals.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What is an effect of shaft misalignment?
A. Vibrations and damages to components.
B. Oil overheating.
C. Seal bulging.
D. Decrease in rpm.

A

A. Vibrations and damages to components.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

A return oil tank is pressurized. What is the cause?
A. Closed outlet valve.
B. Plugged vent.
C. Closed return valve.
D. Plugged drain.

A

B. Plugged vent.

17
Q

A single-stage compressor is functioning properly, but fails to maintain required air volume. What is the cause?
A. Usage demand too high.
B. Oversized compressor.
C. Excessive piston ring leakage.
D. Low crank case oil level.

A

A. Usage demand too high.

18
Q

A new blower fan is installed in a high temperature environment. Which type of drive is required?
A. Pneumatic drive.
B. Chain drive.
C. Direct drive.
D. Belt drive.

A

C. Direct drive.

19
Q

Which type of tool is used in an oxygen-enriched environment?
A. Chrome tools.
B. Carbon fibre tools.
C. Anti-sparking tools.
D. Rubber-protected tools.

A

C. Anti-sparking tools.

20
Q

A compressor in a dirty environment does not operate correctly and constantly overheats. What is the cause?
A. Plugged discharge.
B. Plugged intake.
C. Slipping belt.
D. Faulty tank input check valve.

A

D. Faulty tank input check valve.

21
Q

Internal components in pneumatic tools are rusting. What is the cause?
A. Incorrect tool oil.
B. Excessive tool oil.
C. Excessive ambient air temperature.
D. Moisture in air system.

A

D. Moisture in air system.

22
Q

A 36-in. pipe wrench is used to rotate a mild steel pipe. The pipe wrench continuously slips. What is the cause?
A. Pipe wrench too small.
B. Material build-up in between teeth.
C. Incorrect thimble setting.
D. Pipe wrench teeth are new.

A

B. Material build-up in between teeth.

23
Q

When welding mild steel plate with a 7018 rod, there is difficulty in maintaining an arc. What is the cause?
A. Damp rod.
B. Incorrect rod diameter.
C. No ground.
D. Wrong polarity.

A

D. Wrong polarity.