Random 3 Flashcards
What are the two types of surface preparation power cleaning tools used for small nonskid repair areas
The tenant, the descobrader
How long is the ALBAR 8
9 feet
How long is the ALBAR 15
15 feet
How long is the ALBAR 20
20 feet
How long is the ALBAR 24
25 feet
What is the ALBAR 8 used for
Shipboard movement and spotting H – 46 aircraft
What is the ALBAR 15 used for
Moving most land-based and shipboard aircraft weighing to 90,000 pounds
What length can the ALBAR 15 be extended to
To make the 20 & 24 ALBARs
The 20 ALBAR Was designed to handle what type of aircraft
RH-53D
CH-53E
AV-8B
FA-18 ashore
The 24 ALBAR Was designed to handle what type of aircraft
SH-60 B helicopter
What ALBAR Can be used aboard ship with the AS/ 32-31 tow tractor to tow the FA-18 safety
The 15 ALBAR Due to the lower height of the tractor
What is the Navair 00-80T-105
CVN natops Manuel
What is the Navair 00-80T-106
The natops for LHA & LHDs
Overall responsibility of the aircraft elevators belong to who
V-1 flight deck
V-3 hanger deck
A Division
When should elevator stanchions be placed in automatic
Never
How are the stanchions lowered
Automatically by action of hydraulic engine mounted limit switches
With all pumps in use and elevator loaded to capacity how long is the duty cycle
60 seconds
In the event of a loss of electric power at any point in the cycle what will happen
The capacity of the pressure tanks will permit the returning of the load to flightdeck level
How long will be residual power last
30 minutes of the loss of power
The Control station for the elevator contains what
Master switch, horn button, horn cut out, power available light, control energized light
What is the replacement of the NC-2A
A/S 37-3 MEPP
When will automatic shutdown of the MEPP occur
Engine exceeds 2400 rpm, pressure drops below 10 psi, engine temperature rises above 220°
How many parts does the GSE training and licensing program have
2
Phase 1
Phase 2
What does phase 1 of the GSE training in licensing program consist of
Learning about the GSE, pre-and post op procedures, safety, operating procedures
What does phase 2 of the GSE training program consist of
Using GSE on aircraft, on the job training, servicing, maintenance
What is the proper name of the yellow license
OPNAV form 4790.102
What is the cure time of primer
Between six and 12 hours depending on weather
How wide should wheel stop coaming be marked
12 inches wide
Bulkhead markings or placed how high from the deck and at what intervals
14 feet up from the deck at 10 frame intervals
What is the only aircraft the NWC-4 is not approved for
H-2
What wheel chock is designed for the H-2
NWC-4A
What type of chock is not authorized for shore use
Metal chocks
What three sizes are approved for shore use
Up to 33 inches in diameter, over 33 inches in diameter, dual wheel chock
What is the safe working load of the TD – 1A
10,000 pounds
How much does TD – 1A weigh
12 pounds
What is the safe working load of the aero tiedown assembly
30,000 pounds
How much does the aero tiedown assembly weigh
102 pounds
When using bolt cutters what two types of metal should be avoided
Spring metal, tempered metal
What are the two types of Sanders used in the Navy
Electric and pneumatic
What portable tool should you used to scale out a corner
Needle impact scaler
What are the five types of PPE
Foot, Eye, hand, hearing, head
What tow tractor is found on the flight deck
A/S 32A-31A
