Quiz - Lubrication Flashcards

1
Q

The measure of oil’s ability to flow is know as…

a) It’s flashpoint
b) It’s pour point
c) It’s emulsibility
d) It’s viscosity

A

d) It’s viscosity

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

The lubrication entry point for an oil lift bearing would be…

a) In the loaded zone
b) 180° opposite to the loaded zone
c) 90° from the unloaded zone in the direction of rotation
d) 90° from the unloaded zone opposite to the direction of rotation

A

a) In the loaded zone

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Of the following, which lubrication system would be best suited for large compressor applications?

a) Air/Oil system
b) Block lubrication system
c) Mechanical lubrication system
d) Oil mist system

A

b) Block lubrication system

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Under general conditions, when applying grease to a bearing in a pillow block housing, the bearing should be packed….

a) Full with the housing left empty
b) Halfway up the bottom rolling element
c) 80% to 100% full, with the housing packed 1/3 to 1/2 full
d) 1/3 to 1/2 full, with the housing also packed 1/3 to 1/2 full

A

c) 80% to 100% full, with the housing packed 1/3 to 1/2 full

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Oil in an anti-friction bearing housing should be….

a) Completely covering the bottom rolling element
b) Completely submerging the bearing
c) Halfway up the bottom rolling element
d) Halfway up the bearing

A

c) Halfway up the bottom rolling element

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Which method of lubrication is frequently recommended for high speed, anti-friction bearings?

a) Oil bath
b) Oil mist lubrication
c) Oil ring
d) Splash lubrication

A

b) Oil mist lubrication

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

A higher viscosity fluid would have ________ than a lower viscosity fluid.

a) Less fluid friction
b) A better viscosity index
c) Greater sealing ability
d) More entrained waxes

A

c) Greater sealing ability

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Of the following which one would probably NOT be a contributor to boundary film lubrication?

a) Low speeds
b) High Viscosity
c) High heat
d) Insufficient amount of lubricant

A

b) High Viscosity

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Which of the following is NOT a characteristic of petroleum based oils?

a) They do not wear out
b) In their pure state they are corrosive free
c) They can be re-refined
d) They have poor demulsibility

A

d) They have poor demulsibility

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Which type of friction would produce the greatest heat?

a) Fluid
b) Rolling
c) Sliding
d) Mixing

A

c) Sliding

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What would be the pour point of oil if it showed no movement when held horizontally for 5 seconds at 12°C?

a) 6°C
b) 9°C
c) 12°C
d) 15°C

A

d) 15°C
Pour point is 3°C above the temperature at which the oil shows no movement from a container held horizontally for 5 seconds.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Which of the following is NOT important when considering the pour point of a lubricant?

a) Lowest temperature it will flow into bearings
b) Lowest start-up temperature
c) Lowest pump operating tempurature
d) Lowest viscosity index

A

d) Lowest viscosity index

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Which of the following is NOT a function of the lubricant?

a) Aids in sealing
b) Flushes away contaminants
c) Reduces friction
d) Retains heat

A

d) Retains heat

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

A bottle lubricator relies on _______ to deliver oil to the lubrication point.

a) Capillary action
b) Centrifugal force
c) Heat
d) Vibration

A

d) Vibration

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Calculate the surface speed, in feet per minute, of a 2” diameter shaft turning at 120 rpm.

a) 62.8 ft/min
b) 82.2 ft/min
c) 94.5 ft/min
d) 101.8 ft/min

A

a) 62.8 ft/min

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Wick feed oilers rely on _______ to deliver oil to the lubrication point.

a) Capillary action
b) Centrifugal force
c) Gravity
d) Heat

A

a) Capillary action

17
Q

Which of the following would be classified as a “soap” thickener for grease?

a) Bentonite clay
b) Calcium
c) Polyurea
d) Silicone

A

b) Calcium