Practical Techniques Flashcards
Why is refluxing done?
It allows flammable substances in slow reactions to continue reacting without losing any of the products.
What would happen to substances that need to be refluxed if they were heated in a beaker instead?
They would evaporate or catch fire.
Describe the structure of refluxing equipment.
- Round-bottomed flask with anti-bumping granules in the reaction mixture
- Heat is applied from the bottom
- Liebig condenser attached to the top -> Water flows in at the bottom and leaves at the top
When refluxing, what type of heating is usually used?
Electrical (e.g. hot plates), so as to avoid naked flames that might ignite the compounds.
Describe the structure of distillation equipment.
- Round-bottomed flask
- Thermometer at the top near the junction with a Liebig condenser
- Heat is applied to the bottom of the flask
- Conical flask at the end of the Liebig condenser to collect the products
When might distillation be used?
- Separating substances with different boiling points
* Separating off a product of lower boiling point as it forms (e.g. an aldehyde)
What piece of equipment is used to separate aqueous and organic mixtures?
Separating funnel
Describe how you can remove traces of water from a mixture.
- Add an anhydrous salt, such as MgSO₄ or CaCl₂ -> This binds to any of the water
- At first, the organic layer will be lumpy.
- Add more until the mixture looks like a snow globe when swirled.
- Filter to remove the drying agent.
Give two examples of drying agent.
- MgSO₄
* CaCl₂
How can you remove a drying agent from an organic mixture?
Filtration
What is a good physical way of determining the purity of a liquid organic product?
Measuring the boiling point using distillation apparatus. See the range at which it boils too.
Why might simple distillation not always be suitable for separating organic products? What is the solution?
Some organic liquids:
• Have high boiling points
• Decompose when they’re heated
Instead, steam distillation can be used.
What is steam distillation and why is it used?
- It is normal distillation, except steam is pumped into the immiscible product
- This lowers the boiling point of the organic product so that it can be distilled out of the mixture and before it decomposes
Will steam distillation work with all products?
No, the product must be immiscible with water.
Describe the setup for steam distillation.
Normal distillation setup, except:
• Conical flask with water being heated
• This is connected to a tube that feeds steam into the organic product
(See diagram pg 224 of revision guide)
In steam distillation, what happens if the product you are trying to collect is less volatile (higher boiling point) than the other components?
- The organic product and the steam will evaporate out of the impure mixture together.
- These can then be separated using separating funnel or solvent extraction.
What technique is used to separate an organic product from an impurity when both are soluble in water?
Solvent extraction
Describe solvent extraction.
There is an organic product and impurity, both of which are soluble in water:
1) Add the impure compound to a separating funnel and add some water. Shake well.
2) Add an organic solvent in which the product is more soluble than in water. Shake well. This will dissolve the product into the organic solvent.
3) You can also add a salt to the mixture, which causes the organic product to move into the organic layer.
4) Open the tap and run each layer off into a separate container.
In solvent extraction, why might a salt be added? How does this work?
- The salt causes the organic product (which is also soluble in water) to move more into the organic layer.
- This is because the salt makes the water even more polar, so the organic product is less soluble in it.
What is washing?
Adding another liquid to an impure liquid and shaking.
Does washing have to be with water?
No
What is washing used for?
Removing impurities that cannot be removed by solvent extraction (i.e. impurities that are also in the organic layer when you want the organic product).
How can you remove an organic acid impurity from the organic layer in a separating funnel?
“Washing”:
• Add aqueous sodium hydrogencarbonate
• This reacts to give CO₂ and a salt of the acid, which dissolves in the aqueous layer
• The organic product remains in the organic layer and can be separated from the aqueous layer using a separating funnel
What are the two types of filtration?
- Gravity filtration
* Filtration under reduced pressure