Locating points Flashcards

1
Q

: Good facilities should be provided for locating the work.

A

LOCATING POINTS

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Location 1:
 Location should ensure _______
throughout all sequence of operation.

A

equal distribution of forces

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Location 2: Location should be

A

hard resistant, wear resistant and
high degree of accuracy.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Location 3:
 Movement of workpiece should be ____.

A

restricted

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Location 4: Should be _____ to avoid improper locations of
the workpiece

A

fool proofed

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Location 5:  Should facilitate _____

A

easy and quick loading of workpiece.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Location 6: should be avoided.

A

Redundant Locators

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Location 7:  _____ must be avoided.

A

Sharp corners

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Location 8:  At least______ should be established.

A

one datum surface

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

The devices that restrict a workpiece’s movement are the ____4.

A

locators

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

All twelve degrees of freedom must be ______ of a workpiece.

A

restricted to ensure proper referencing

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

are fixed-height locators. They precisely locate a surface in one axis. Though solid supports may be machined directly into a tool body, a more-economical method is using installed supports, such asrest buttons.

A

Solid Supports

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

are variable-height locators. Like solid supports, they will also precisely locate a surface in one axis. These supports are used where workpiece variations require adjustable support to suit different heights. These supports are used mainly for cast or forged workpieces that have uneven or irregular mounting surfaces.

A

Adjustable supports

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

are a form of adjustable support used when a compensating support is required. Although these supports can be fixed in position, in most cases equalizing supports float to accommodate workpiece variations. As one side of the equalizing support is depressed, the other side raises the same amount to maintain part contact. In most cases adjustable and equalizing supports are used along with solid supports.

A

Equalizing supports

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Locating a workpiece from its ______ is the most-common locating method.

A

external edges

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

The bottom, or primary, locating surface is positioned on three supports, based on the geometry principle that three points are needed to

A

fully define a plane.

17
Q

Two adjacent edges, usually _____ to each other, are then used to complete the location.

A

perpendicular

18
Q

The most-common way to locate a workpiece from its external profile is the _____

A

3-2-1, or six-point, locational method.