LF Questions Flashcards
Q1. According to STP - What are the 3 Golden rules to follow when applying foam?
- Do not begin to apply foam unless you have enough to extinguish the fire or cover the fuel spill
- Point branch away from fire until good finished foam is being produced
- You cannot mix different foam concentrates
Q2. According to STP - List 3 hazards/considerations when using CAFS at a structure fire.
- CAFS hose lines have a build up of pressure when the branch is closed causing a larger jet reaction than a standard hose
- Slug flow – When the proportion of foam, air and water is wrong causing finished foam to “shudder” or “pulsate” as it is exiting the branch
- Does not contain enough water for internal attack
Q3. According to STP - List 5 actions to take when combatting a natural gas leak with no fire involved.
- Don structural PPE and SCBA
- Evacuate all persons from the immediate area
- Remove all sources of ignition
- Respond Gas company
- Only use intrinsically safe equipment
Q4. According to STP - Acetylene is a very volatile gas, exploding cylinders can penetrate double brick walls or metal freight containers & land 200m away. How many hours after the cylinder is removed from the fire or heat source, if it is not cooled, can this explosion occur?
- 24hrs
Q5. According to STP - When reading a fire, we need indicators to base our decisions on, what are the most important indicators?
- B-SAHF – building, smoke, air track, heat & flame
Q6. According to STP - What techniques enable us to control the interior environment during a structure fire?
- Gas cooling and hose stream techniques
Q7. According to STP - List 2 common hose laying techniques that can be used by firefighters?
- Traditional S lay (flaked).
- Cleveland load/coiled (attack pack)
Q8. Complete the following in relation to the Fire and Rescue NSW Act 1989 Part 3, Division 1, Section 11 Brigades to proceed with speed to suspected fires or hazardous material incident………?
(1) When there is an alarm of fire, a fire brigade must, despite anything to the contrary in any Act, proceed with all speed to the fire and try by all possible means to extinguish it and save any lives and property that are in danger.
(2) When there is a report of a hazardous material incident, a fire brigade must, despite anything to the contrary in any Act proceed with all speed to the site of the incident, and try by all possible means to render the site of the incident safe and save any lives and property that are in danger.
Q9. Complete the following in relation to the Fire and Rescue NSW Act 1989 Part 3, Division 1, Section 12 of the FRNSW Act, Investigation of reported fires and Hazardous material incident ?
(1) The officer in charge may, with or without members of a fire brigade, enter any place—
(a) in respect of which an alarm of fire is raised to ascertain whether there is a fire at the place, or
(b) in respect of which a report of a hazardous material incident has been made to ascertain whether there is any hazardous material at the place that is, or is about to be, the subject of a hazardous material incident.
(2) Reasonable force, whether by breaking down gates or fences or breaking open doors or otherwise, may be used to gain entry.
Q10. Section 13, of the FRNSW Act states the “General Powers of Officers at fires and hazardous material incidents”. State this provision.
(1) At a fire, the officer in charge—
(a) may take such measures as the officer thinks proper for the protection and saving of life and property and for the control and extinguishing of the fire, and
(b) is to control and direct the operations of any fire brigade.
(1A) At the site of a hazardous material incident, the officer in charge—
(a) may take such measures as the officer thinks proper for the protection and saving of life and property, for confining and ending the incident and for rendering the site safe, and
(b) is to control and direct the operations of any fire brigade.
The site is taken to be such area in the vicinity of the incident as is for the time being determined by the officer in charge.
(2) If the fire is a bush fire (including a grass fire), the officer in charge is, as far as practicable, to carry into effect any plan of operations in force under section 52 of the Rural Fires Act 1997 in relation to the place where the fire occurs.
Q11. Section 19 of the FRNSW Act lists the powers at fires and hazardous material incidents. State the provisions of this Section: “General power to remove persons or obstacles.”
- The officer in charge at a fire or hazardous material incident may cause to be removed any person, vehicle, vessel or thing the presence of whom or which at or near a fire or hazardous material incident might, in the officer’s opinion, interfere with the work of any fire brigade or the exercise of any of the officer’s functions.
Q12. At an incident that has been declared a crime scene, a member of the public seeks details from you, the senior firefighter/officer on duty, about the incident. State your response according to the Fire Brigades Regulation (2014) Clause 22, Disclosure of information.
- A firefighter must not disclose any information obtained in the firefighter’s capacity as a firefighter unless the disclosure is made:
(a) in the exercise of the firefighter’s functions, or
(b) about factual matters that are generally available to the public, or
(c) by an approved firefighter to media representatives concerning operations at a fire or other incident, or
(d) at the direction or with the permission of the Commissioner, or
(e) with other lawful excuse.
Q13. Section 17 of the Fire Brigades Regulation (2014) refers to unacceptable behaviour. List five circumstances when a firefighter’s behaviour would be deemed unacceptable.
- A firefighter must not:
(a) come on duty while under the influence of alcohol or a drug,
(b) while on duty, consume, use or possess any alcohol or drug,
(c) while on duty, gamble in circumstances that adversely affect the discipline or efficiency of Fire and Rescue NSW,
(e) smoke in any public place while in uniform,
(f) while off duty, enter or remain on departmental premises without authority
Q14. As stated in the Standing Orders, to avoid serious accidents at intersections when responding to an emergency, What actions should drivers of responding vehicles approaching a stop sign or red signal take?
- Slow down and enter the intersection at 8 kph or less. if safe to proceed, continue across the intersection. If not safe to proceed (would involve the vehicle in an accident), the driver must come to a halt and not move off again until it is safe to proceed.
Q15. According to Standing Orders, when are seatbelts required to be worn when travelling in FRNSW vehicles (including tankers)?
- By all members when travelling in Fire and Rescue NSW vehicles, including a water tanker.
Q16. According to Standing Orders, with no impact of the service delivery, List the procedures to be followed if drivers of FRNSW vehicles are involved in an accident.
- advise the other driver to contact Fire and Rescue NSW’s Fleet Unit to obtain the relevant claim number and contact details for Fire and Rescue NSW’s insurer. The FRNSW vehicle driver is to be suspended from driving for the balance of the shift on duty unless required to continue to maintain service delivery.
- Station Commanders/Supervisors must complete an Agency Member Motor Vehicle Claim Form and submit to their Duty Commander with a covering memo
- Duty Commander must investigate
- Agency Member Motor Vehicle Claim Form then forwarded to Fleet Management Unit to process the insurance claim
- If any injury is involved a NIIENM form must be completed
Q17. Fire Brigades Regulation, Part 3, Section 14: Firefighters to acquire and maintain knowledge of legislation, orders, and functions. List the provisions.
(1) A firefighter must acquire and maintain a thorough knowledge of, and must comply with the requirements of, the Act, this Regulation and the Commissioner’s Orders.
(2) A firefighter must acquire and maintain the knowledge and skills that are relevant to the performance of the firefighter’s functions.
Q18. According to STP -The National Construction Code classes buildings “Class 1” through to “Class 10”. The class of building is a measure of the buildings likely: List these four points.
- use
- fire load
- population
- mobility of the occupants (ie whether they are sleeping or alert)
Q19. According to the Fire Investigation toolkit on the Intranet, when should you request FIRU for assistance?
- A loss of life or expected loss of life at a fire
- The fire is considered major (i.e. 4th Alarm or above, significant community impact or unusual fire behaviour), or
- The Origin and Cause of the fire is not apparent.
Q20. As listed in STP - What form populated by firefighters gives the Fire Investigator a summary of firefighter actions at an incident.
- SOFA form – summary of observations & firefighter actions
Q21. STP - Details how a structure fire will burn within one of two burning regimes. List and describe the regimes.
- Fuel controlled – fires with more than enough oxygen and heat for combustion, but are controlled by the availability of fuel
- Ventilation controlled - where fire development and the Heat Release Rate (HRR) is dictated by the availability of oxygen.
Q22. STP - Identifies the search priority in multi story buildings, list the priorities.
- Search priority starts at the fire floor, then floor above and then the top floor
Q23. STP - Outlines when a working at a task/tactical level and a firefighter becomes trapped, injured missing or overdue. What message should be sent to draw attention to the situation?
- mayday message
Q24. According to STP - When is an Incident Management System required to be used at incidents FRNSW attends?
- It applies at every incident FRNSW attends from when the first FRNSW resource arrives at the incident to when the last resource is released.
Q25. According to STP -There are eight strategic functions of command the Incident Commander needs to address. List all eight.
- Deployment,
- Command,
- Situation evaluation,
- Incident action planning,
- Incident communications,
- Incident structure,
- Review and revision,
- Escalation and de-escalation
Q26. According to STP - At every incident there must be a steady, adequate, and timely stream of resources. Who is the only person to deploy resources at an incident?
- The Incident Commander
Q27. A driver in a road tunnel noticed smoke coming from the engine compartment of their car and immediately pulled into the emergency break down bay and called 000. The Tunnel Control Centre closed the tunnel allowing attending fire crews access to extinguish the fire. Peak hour traffic is starting to build at the entrance to the tunnel and thick smoke is throughout. List the Smoke Management Systems found in road tunnels that could assist in clearing the smoke?
- longitudinal ventilation (jet fans)
- ducted ventilation
- natural ventilation
- a combination of the above.
Q28. According to SOGs -As an incident develops and crews become fatigued, they will need to be rested. Name and describe the two ways crews can be rested.
- Recycle – Crew stops work for a short period just outside the Hot Zone, to rest, rehydrate, and replenish air cylinders if relevant. They remain accountable to IC or Sector, Group or Division commander (SGD Commander), as per the incident structure.
- Full rehabilitation – Crew is released and moves to the rehabilitation area. Once there, they are accountable to a Rehabilitation Officer.
Q29. According to SOGs - List and describe the three incident phases.
- Life at risk phase – where there are savable human lives. The incident is uncontrolled and requires rapid actions to control the risks to life. High level risk acceptable
- Expanding phase – where the incident is uncontrolled and likely to expand. It requires rapid actions to control risks to life and property. Some level risk acceptable
- Contained phase – there are sufficient resources to contain the incident within the defined area. There is no life at risk, or life or property have already been lost. Minimise risk
Q30. According to Standing Orders who are the people authorised to ride on FRNSW appliances?
- firefighters in the course of their duty;
- employees of FRNSW whose duty requires their attendance at an emergency;
- members of other emergency services at the discretion of the member in charge; or
- other persons authorised by the Commissioner.
Q32. According to STP - List and describe three ways foam controls and extinguishes fire.
- Excluding the fire’s supply of oxygen (smothering)
- Suppressing flammable vapours to stop them from igniting
- Cooling the surface temperature to prevent re-ignition
Q33. According to STP – What are the characteristics of liquid petroleum gas?
- Odourless, colourless, heavier than air
Q34. According to STP - What is the term used when a liquid within a container reaches a temperature well above its boiling temperature, boils, expands and the container fails sending flammable gas outwards where it ignites.
- BLEVE - A boiling liquid expanding vapour explosion (BLEVE)
Q35. According to STP - What can be used to conduct a thermal check of an acetylene cylinder.
- TIC, Infrared thermometer, wetting test
Q36. Expand the Acronym - SISIACMR
- Safe approach,
- incident control,
- scene security,
- identify hazardous material,
- assess potential harm and minimize environmental contamination,
- call in resources,
- monitor information,
- render safe & decontaminate
Q37. According to STP - What is the most suitable extinguishing agent for rubber fires?
- water
Q38. According to STP -There are several stages of Lithium-Ion battery failure list and describe the stages.
- Stage 1 – abuse factor (thermal, electrical or mechanical abuse)
- Stage 2 – off gas generation (occurs regardless of cell form factor)
- Stage 3 – smoke generation (catastrophic failure is imminent)
- Stage 4 – fire generation (likelihood of propagation drastically increases)
Q39. According to the Workplace Safety toolkit on the intranet, what should you complete when a work-related injury, near miss, exposure or illness occurs and in what timeframe after the occurrence should it be submitted?
- A Notification of Injury, Illness, Exposure and Near Miss (NIIENM) form submitted within 24 hours of occurrence.
Q40. According to the toolkit on the intranet - If you are unable to submit or fill out a NIIENM who else can submit one for you?
- Supervisor or co-worker.
Q41. In New South Wales, Emergency Services carry out land-based rescues under what Act?
- State Emergency and Rescue Management ACT 1989
Q42. As stated in the SERM Act,1989 who is responsible for coordinating rescue operations and for determining the priorities of action to be taken in rescue operations?
- NSW Police Force
Q43. According to STP - FRNSW uses the YOU principle to establish priorities of safety at a rescue incident. What are these priorities of safety?
- Yourself and other rescuers
- Other persons not involved (bystanders)
- Unfortunate person(s) involved
Q44. According to STP -What is the correct PPC and procedure for fire protection at an MVA?
- One firefighter in structural PPC & SCBA (not donned), charged line of 38mm @ 400kpa, pump with recirculating valve open. If fire occurs charge to 800kpa.
Q45. According to STP - What environments should SCBA be worn in?
- HOTS: Heated or extremely low temperatures, oxygen deficient or enriched atmospheres, toxic atmospheres, smoke.
Q46. Owners and occupiers of premises can deposit keys at their nearest fire station so that firefighters can gain access without causing unnecessary damage. Located in the Forms filing cabinet on the intranet, name the two forms that need to be completed when receiving keys to private premises.
- Keys deposit – station commanders
- Keys to private premises form
Q47. As stated in the Health, Fitness and Wellbeing Toolkit- What is it a mandatory requirement to complete prior to undertaking the annual Fitness Drill?
- Physical activity readiness questionnaire - PARQ
Q48. According to Operations Bulletin 2020-04 - Failure to report damage. When an appliance is found to have unreported damage, the Fleet Operations Officer or Regional Maintenance Officer will notify the Station, Duty, and Zone Commander in writing. The responsible station must submit what form within 8 days?
- Agency Member Motor Vehicle Claim Form
Q49. According to the Fire ePermit policy, a fire permit issued within the ‘Bush Fire Danger’ period will be valid for a period of how many days from the date of issue?
- 7 days maximum
Q50. According to the Fire ePermit policy, what aspect of the planned fire does the permit take into account.
- The safety aspect
Q51. According to STP - Where should Warden Intercom Points be in a building?
- With emergency intercom control and indicating equipment (EICIE)
- Within 4m of an exit: within each emergency zone; within each story
- Within emergency lift shaft
- Adjacent to fire detection control indicating equipment (FDCIE) if remote from EICIE
Q52. According to STP, name the components in an AS 2118.1 sprinkler alarm valve room.
- Main stop valve,
- test drain,
- sprinkler test facility,
- sprinkler alarm valve,
- system pressure gauge,
- deluge valve,
- water supply with water supply pressure gauge
Q53. According to STP, there are two control measures when dealing with live power at an incident. List and describe them.
- Turning off power - Firefighters can turn off the main switch, removing fuses and switching off circuit breakers at the switchboard.
- Isolating power - Energy Authority disconnect power from the network.
Q54. According to STP - Firefighters can ‘turn off’ a solar power system to stop electricity feeding into the structure’s circuits or back to the electricity network if configured to do so. State the recommended procedure.
- On-site consultation: determine whether it is appropriate to turn solar power system off and how best to do so
- Assume switchboard is live: Don electrical safety gloves then over-gloves. Have your helmet visor down and look away
- Follow the shutdown procedure: This may be on or near the switchboard or inverter. If not found, turn off the inverter main switch then turn off the solar panel main switch
- Consider if benefits outweigh risks: Restrict work as far as reasonably practical to that required to protect life or prevent dangerous expansion of the incident
- Isolate the power: If required, have the owner/occupier contact their electrician to isolate the power
Q55. According to STP -When a battery energy storage system is present at a residence, there should be an indicator to alert you to this. What is an example of an indicator, located outside the switchboard.
- energy storage system “ES sticker”- outside the switchboard. There should also be data sheets, or further information about this type of system.
Q56. Operations Bulletin 2023-01- Lists operational actions to follow when dealing with Lithium
- If connected to mains power ensure switched off before applying water
- Knock-down any fire using copious amounts of water.
- Cool the battery with a cooling stream of water.
- Submerge the device in a suitable container of water if safe to do so. Use a tool such as a long-handled shovel to move the device.
- If unable to submerge the device, continue cooling and conduct thermal checks every 15 min until ambient temperature is maintained for 60 min.
- Ensure that all cells are accounted for by searching the area around the device.
- Notify FireCOM that the incident involves a lithium-ion device.
Q57. According to STP - If solar panels, or the attached isolators, are on fire, in addition to the considerations with turning off an alternative power source what actions should firefighters take?
- Conduct firefighting from the ground or an aerial appliance. Do not get onto the roof to extinguish the fire. Do not put a ladder against the roof as the gutter may be electrified.
- Extinguish the fire with a spray nozzle, using a pulse spray in a dispersed pattern
- If the solar panel is at ground level, consider using CO2 to extinguish the fire, ensuring that there is at least 250 mm air gap between the CO2 extinguisher nozzle and any electrified components.
- NSW Fair Trading notification form to be completed at completion of incident
Q59. According to STP - Overhaul is a procedure we follow after we attend an incident and extinguish the fire. For your safety during overhaul what is it essential for you to do?
- Wear SCBA and a full set of firefighting clothing
- Perform atmospheric monitoring using a gas detector
Q60. According to STP - What is the minimum PPE that can be worn at a bush fire?
- Level 2 ppc: multi-porpose helmet, goggles, multipurpose jacket, GP gloves, firefighting gloves (direct attack), duty wear trousers, FF boots, P2.
Q61. According to STP - Property protection is the act of protecting property from the impact of a wildfire. At a major wildfire, FRNSW crews generally engage in property protection roles. We generally have 3 strategies for carrying out property protection. Name and describe them.
- Line defense – protect the perimeter of the property until resources are sufficient for an offensive attack.
- Ember defense – extinguishing small fires that occur in and around buildings, when and as they occur.
- Backstop defense – Firefighters withdraw temporarily a nearby suitable safe refuge. After the main fire front subsides, move forward to put out the property on fire.
Q62. Operations Bulletin 2023-01- Lists the hazards and risks at incidents involving Lithium-ion batteries in small devices. List all as stated in the bulletin.
- Thermal runaway,
- Extreme fire behaviour,
- Release of toxic vapour and gases,
- Hazardous materials and leaked electrolytes,
- Stranded energy,
- Projectiles,
- Secondary ignition
Q63. As described in STP - When conducting ventilation using a fan, what is the most effective inlet/outlet ratio?
- 1:4 – outlet 4x larger than inlet
Q64. According to SOGs - When an LPG container is involved in fire, what area of the container is considered most crucial and a high priority area for cooling?
- The container’s vapour space (area above the liquid)
Q65. As recommended in STP - When conducting ventilation with a fan, the fan should be set back approximately how far from the door.
- Approximately the height of the door.
Q66. According to Work Instruction- “Bagging contaminated gear” What equipment is required for bagging contaminated gear (not PPC) at an incident to minimise the risk presented by hazardous contaminants during storage or transport?
- The appropriate bag for the type of contaminant:
- Asbestos containment bags
- Yellow clinical waste bags
- Clear plastic gear bags for other contaminants, including smoke.
- Cable ties or strong tape to seal the bags.
- A contaminated equipment tag to attach to the bag with relevant details.
Q67. You are responded to a bushfire with four Fire Rescue NSW pumpers two RFS tankers and one inspector, according to SOGs what class is the fire?
- Class 1
Q68. According to the guideline support document for electricity SOGs - Electrical transformers in high density areas of cities maybe situated in underground vaults, if a fire occurs in one of these vaults, CO2 can be injected via a wall mounted or footpath CO2 connection box. What does the number on the connection box indicate?
- The number of CO2 cylinders required to be injected for extinguishment
Q69. According to the guideline support document for electricity SOGs - What factors affect voltage gradient at wires down?
- Composition of the ground
- Moisture content
- Voltage of the electrical source
Q70. According to the guideline support document for electricity SOGs - Conductors allow electricity to easily pass through them. List five conductors.
- Metals
- Human body
- Flame and dense smoke
- Vehicle tyres
- Water – including hose lines
Q71. According to the guideline support document for electricity SOGs - Name four measures to control the risks associated with electricity.
- Stay away from the hazard. Always regard it as live until you know otherwise.
- Assess the risks from at least 8 metres away from the hazard.
- If suspected to be electrically hazardous, establish an Exclusion Zone.
- Have the electricity company isolate power.
Q72. As listed on the SIMS Worksheet: Electrical safety kit - State the inventory stored in the green canvas bag of the electrical safety kit.
- 1x pair insulating gloves
- 1x pair leather overgloves
- 2x non-contact AC voltage detectors, either Modiwark Rescue or GLM Mini Rescue
Q73. According to Recommended practice - When using the gloves from the electrical safety kit, what is the correct donning sequence?
- Put on electrical gloves first.
- Put over-gloves on over the electrical gloves
- The cuff of the electrical glove must extend beyond the cuff of the over-glove.
- The cuff of the electrical glove must be above the cuffs and sleeves of PPC.
Q74. According to SOGs - FRNSW has an interagency notification policy, list the reasons NSW Police are required to be notified.
- Possible terrorist incident
- Crime investigation
- Site, crowd, traffic and evacuation management
- Rescue incidents
Q75. You are responded to fire in a Correctional facility, centre or complex operated by government agencies or private contractors. As stated in FRNSW SOGs on arrival what actions should be taken?
- Identify and liaise with the Emergency Coordinator.
- While waiting to enter start developing IAP by accessing information
- Where entry to the facility is delayed, nominate a staging area and advise FireCOM to inform responding resources.
- Remain at stating area until met by the Emergency Coordinator
- Always remain outside facility on standby if it is unsafe to enter
- At the main entry, access the Red Fire Emergency Plan Box and brief crew about the facility.
- Prepare the appliance and secure equipment before entering the facility. List all equipment to be taken in.
Q76. According to the Preventing and Managing Unreasonable Behaviour and Bullying Policy, what is the definition of workplace bullying?
- Workplace bullying is repeated and unreasonable behaviour directed towards a worker or a group of workers that creates a risk to health and safety.
Q78. According to the ‘Firefighter’ role description found on the Intranet, list 5 Duties/Accountabilities required in this role.
- Contribute to station’s community prevention, risk reduction planning and engagement programs and activities
- Attend fire and other emergency incidents providing expert knowledge and assistance commensurate with rank
- Contribute to station’s operational readiness, including the maintenance of appliances, tools and equipment
- Assist with investigation into the cause of fires
- Support station officer in actions to achieve FRNSW’s goals of protecting life, property and other initiatives under the Plus Plan
Q79. According to STP - What guidelines (general rule) should be followed when tasking crews at a residential structure fire?
- As a general rule, in the absence of visible victims or in situations where victim location is unknown, the first arriving crew will be tasked with Fire Attack.
Q80. According to STP -What is recommended configuration for relay pumping operation?
- Base pump is largest capacity appliance
- 5 lengths 70mm between base and relay
- 7 lengths 70mm relay to relay or fireground pump
- Minimum two lines so in case one is damaged water is still supplied to fireground
Q81. According to STP – ‘Fire Safety and Investigation’ there are four classifications of cause. Name and describe them.
- Accidental - Fire which starts accidently from human activity or influence.
- Incendiary - Fire which starts from deliberate and intentional human act
- Natural - Fire which starts by a natural act without and human influence
- Undetermined - Fire where the cause cannot be identified
Q82. Whilst participating in a community event at the local oval and armed offender attack occurs. According to SOGs, what actions should you take?
- Escape, if safe to do so
- Hide, if can’t escape.
- Tell, FireCom/Police if safe to do so
According to SOGs - There are many duties of the BA Control Operator, list five.
- Establish BA Control as close to the entry/exit point as possible.
- Check and enter all details on the BA Control Board.
- Calculate and monitor entry and exit times.
- Monitor all radio communications within the sector.
- Indicate to exiting BA crews the locations of the BA staging and rehab area.
Q84. According to Firefighters Training Manual - The numbers relayed back from FireCOM for the Hazmat Action Guide (HAG) sheet are used to determine PPE, form, hazards, effect with water, action, firefighting, and personnel decontamination. TX at the end of the transmission means there is text. What does the text usually refer to?
- Usually related to Additional Personal Protection (APP).
Q85. According to SOGs - What can P2 particle masks be used to protect against?
- Known low concentrations of inert dust (ie from cutting wood or metal)
- Concrete, stone and masonry cutting operations where the work piece can be kept wet.
- The particulates in bushfire smoke.
- Contamination by body fluids.
Q86. According to SOGs - At any incident, the Incident Commander will consider the incident phase and the risk that may be accepted. Describe the life at risk phase.
- Life at risk phase, where there are savable human lives. The incident is uncontrolled and requires rapid actions to control the risks to lives. A higher level of risk may be acceptable.
Q87. According to Firefighters Training Manual -You attend a house fire at 2am and on arrival notice a small amount of smoke issuing from the ground level of a 2-storey residence. Two cars are parked in the driveway. What three principles should you keep in mind when forcing entry?
- enter without undue delay;
- enter with the minimum of structural damage;
- enter so as to provide access to as much of the building as possible.
Q88. According to SOGs -You respond to a building fire and the contaminated run- off/pollutant is impacting a canal that runs into a creek. Which agencies are you required to notify?
- Roads and Maritime Services/Transport for NSW
- Environmental Protection Agency
Q90. According to SOGs - What are the three basic principles for communication at incidents?
- to use the principles of ICS and ensure an effective span of control;
- to establish a flow of information at all levels of the incident, without overwhelming the IC or ComCen with superfluous data;
- to ensure the safety of firefighters by using effective communication.
Q92. According to SOGs - Emergency Response Teams have varying levels of skills, equipment, and training. Depending on the hazards involved, the IC must determine, from Pre-Incident Planning and discussion with the Emergency Response Team Leader, their role at an incident. Name three activities Emergency Response Team can participate in.
- Specialist advice to the IC relating to hazards, industrial processes and installed fire systems.
- Operation of valves and other industrial processes.
- Fire attack under the control of FRNSW officers.
Q93. SOGs describe how to de-escalate an incident. What is de-escalation?
- The scaling down of FRNSW involvement at an incident from both a strategic and tactical level. Delegated functions handed back to the IC. The IC determines incident has been contained and resources can be released.
Q94. According to SOGs - The Emergency Control Organisation may consist of people identified by coloured helmets, hats, caps, vests, or tabards. Name the members and the identifying colour.
- White: Chief warden, deputy chief warden, communications officer
- Yellow: Floor warden, area warden
- Red: warden
- White cross on a green background: first air officer
Q95. What are the correct meanings for the numerical codes: Codes 1,3,4,6,7
- Code 1 – Responding to an incident or move-up
- Code 3 – On scene at incident or move-up to station
- Code 4 – Available for response. If not return to station state where.
- Code 6 – indicate that FRNSW is responding to a call in a Rural Fire District
- Code 7 - Unavailable for response. State why and code 4 when available.
Q96. You are completing a pre-incident plan for an occupancy located within your station area. Your priorities are confirming correct keys and swipe cards, along with updating information for the MDT. The SO directs you to inspect the Fire Control Room. According to the SOGs, What features are included in a Fire Control Room?
- a fire isolated room with a 2-hour fire rating and separate ventilation
- two exit points, to the front of the building and directly into a fire exit
- Fire Indicator Panel
- Fire Fan Control Panel
- Master Emergency Control Panel
- controls for fire pumps
- Security Alarm and Control Panels
- telephone (direct line outside)
- whiteboard, corkboard and plan table
- Tactical Fire Plans (maps and schematics).
Q97. You are attending an incident at a large cold storage facility. Your SO has directed you to cut into an Insulated Sandwich Panel (ISP). Prior to cutting the ISP, you conduct a risk assessment. According to the SOGs, list the important issues to consider?
Before cutting any ISP, conduct a risk assessment. Important issues to consider
include:
- if there is sufficient time and resources available.
- leaked refrigerant gas which may be pocketed behind panels or in ducting
- electrical wiring or refrigerant gas pipes that may be located behind the panels
- the potential to generate sparks that could ignite flammable refrigerant gas or ESP panel cores
- Weakening of the structure when multiple panels are cut.
- An increase in fire activity due to the introduction of air;
- Have a charged line of hose in place for protection before cutting ISPs.