Laser Alignment Flashcards

1
Q

what are the three basic types of laser alignment systems?

A
  • single reflected beam with single detector
  • dual beam with dual detectors
  • single beam with dual detectors
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

What is dynamic interruption and which systems allow for it?

A

dynamic interruption is where the beam falls outside the range of the detector while you rotate the coupling. the dynamic interruption allows you to readjust the beam back to within the range of the detector without starting over.

  • single reflected beam single detector
  • single beam dual detectors
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What are the key components to a laser detector system?

A
  • Transmitter or detector unit
  • Reflector
  • Bracket
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What part of the laser alignment goes on the shaft of the stationary machine?

A

Laser/Detector

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

What part of the laser alignment goes on the machine to be moved?

A

Prism reflector

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Some units need to be rotated together, some units allow you to take readings at any three of the eight positions located 45 d apart, and on other units you only need to do a ________ degree sweep to get all the information needed for the machine to do its calculations.

A

60-70 degree sweep

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

New laser alignment tools incorporate what features?

A
  • built in inclinometer
  • vibration monitoring
  • backlash detection
  • Bore alignment
  • Thermal growth measurement
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What class laser are used in laser alignment tools?

A

class 2 (visible beam) you can damage your eyes by staring into the beam

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

What can cause beam distortion in laser alignment systems?

A

Extreme heat or steam

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Most micro processors are rated to _____ degrees C

A

Above 0 degrees C

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What are typical dimensions you must enter into the system?

A
  • Laser to prism
  • Laser to coupling center
  • Coupling diameter
  • RPM or default
  • Laser to front foot of motor
  • Front foot of motor to back foot of motor
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Can you check for softfoot with laser alignment?

A

Yes

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

why would you use laser alignment for a bore instead of string alignment?

A

much faster

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q
A
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

The laser beam is emitted from the ?

A

Laser/detector mounted on the stationary machine

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

The prism reflector is mounted where and what does it do?

A

Mounted on the machine to be moved and reflects the laser back to the detector

17
Q

What is used to make sure the laser and shafts are in the exact rotational locations?

A

Inclinometer

18
Q

Laser alignment tool features?

A

Built in inclinometer
- vibration monitoring
- backlash detecting
- bore alignment
- thermal growth measurement
- flatness measurement
- soft foot

19
Q

Heat and steam do what to your laser readings?

A

Cause beam distortion and inaccurate readings